[people/ms/u-boot.git] / include / linux / mii.h

/*
 * linux/mii.h: definitions for MII-compatible transceivers
 * Originally drivers/net/sunhme.h.
 *
 * Copyright (C) 1996, 1999, 2001 David S. Miller (davem@redhat.com)
 */

#ifndef __LINUX_MII_H__
#define __LINUX_MII_H__

/* Generic MII registers. */

#define MII_BMCR	    0x00	/* Basic mode control register */
#define MII_BMSR	    0x01	/* Basic mode status register  */
#define MII_PHYSID1	    0x02	/* PHYS ID 1		       */
#define MII_PHYSID2	    0x03	/* PHYS ID 2		       */
#define MII_ADVERTISE	    0x04	/* Advertisement control reg   */
#define MII_LPA		    0x05	/* Link partner ability reg    */
#define MII_EXPANSION	    0x06	/* Expansion register	       */
#define MII_CTRL1000	    0x09	/* 1000BASE-T control	       */
#define MII_STAT1000	    0x0a	/* 1000BASE-T status	       */
#define MII_ESTATUS	    0x0f	/* Extended Status */
#define MII_DCOUNTER	    0x12	/* Disconnect counter	       */
#define MII_FCSCOUNTER	    0x13	/* False carrier counter       */
#define MII_NWAYTEST	    0x14	/* N-way auto-neg test reg     */
#define MII_RERRCOUNTER     0x15	/* Receive error counter       */
#define MII_SREVISION	    0x16	/* Silicon revision	       */
#define MII_RESV1	    0x17	/* Reserved...		       */
#define MII_LBRERROR	    0x18	/* Lpback, rx, bypass error    */
#define MII_PHYADDR	    0x19	/* PHY address		       */
#define MII_RESV2	    0x1a	/* Reserved...		       */
#define MII_TPISTATUS	    0x1b	/* TPI status for 10mbps       */
#define MII_NCONFIG	    0x1c	/* Network interface config    */

/* Basic mode control register. */
#define BMCR_RESV		0x003f	/* Unused...		       */
#define BMCR_SPEED1000		0x0040	/* MSB of Speed (1000)	       */
#define BMCR_CTST		0x0080	/* Collision test	       */
#define BMCR_FULLDPLX		0x0100	/* Full duplex		       */
#define BMCR_ANRESTART		0x0200	/* Auto negotiation restart    */
#define BMCR_ISOLATE		0x0400	/* Disconnect DP83840 from MII */
#define BMCR_PDOWN		0x0800	/* Powerdown the DP83840       */
#define BMCR_ANENABLE		0x1000	/* Enable auto negotiation     */
#define BMCR_SPEED100		0x2000	/* Select 100Mbps	       */
#define BMCR_LOOPBACK		0x4000	/* TXD loopback bits	       */
#define BMCR_RESET		0x8000	/* Reset the DP83840	       */

/* Basic mode status register. */
#define BMSR_ERCAP		0x0001	/* Ext-reg capability	       */
#define BMSR_JCD		0x0002	/* Jabber detected	       */
#define BMSR_LSTATUS		0x0004	/* Link status		       */
#define BMSR_ANEGCAPABLE	0x0008	/* Able to do auto-negotiation */
#define BMSR_RFAULT		0x0010	/* Remote fault detected       */
#define BMSR_ANEGCOMPLETE	0x0020	/* Auto-negotiation complete   */
#define BMSR_RESV		0x00c0	/* Unused...		       */
#define BMSR_ESTATEN		0x0100	/* Extended Status in R15 */
#define BMSR_100HALF2		0x0200	/* Can do 100BASE-T2 HDX */
#define BMSR_100FULL2		0x0400	/* Can do 100BASE-T2 FDX */
#define BMSR_10HALF		0x0800	/* Can do 10mbps, half-duplex  */
#define BMSR_10FULL		0x1000	/* Can do 10mbps, full-duplex  */
#define BMSR_100HALF		0x2000	/* Can do 100mbps, half-duplex */
#define BMSR_100FULL		0x4000	/* Can do 100mbps, full-duplex */
#define BMSR_100BASE4		0x8000	/* Can do 100mbps, 4k packets  */

/* Advertisement control register. */
#define ADVERTISE_SLCT		0x001f	/* Selector bits	       */
#define ADVERTISE_CSMA		0x0001	/* Only selector supported     */
#define ADVERTISE_10HALF	0x0020	/* Try for 10mbps half-duplex  */
#define ADVERTISE_1000XFULL	0x0020	/* Try for 1000BASE-X full-duplex */
#define ADVERTISE_10FULL	0x0040	/* Try for 10mbps full-duplex  */
#define ADVERTISE_1000XHALF	0x0040	/* Try for 1000BASE-X half-duplex */
#define ADVERTISE_100HALF	0x0080	/* Try for 100mbps half-duplex */
#define ADVERTISE_1000XPAUSE	0x0080	/* Try for 1000BASE-X pause    */
#define ADVERTISE_100FULL	0x0100	/* Try for 100mbps full-duplex */
#define ADVERTISE_1000XPSE_ASYM 0x0100	/* Try for 1000BASE-X asym pause */
#define ADVERTISE_100BASE4	0x0200	/* Try for 100mbps 4k packets  */
#define ADVERTISE_PAUSE_CAP	0x0400	/* Try for pause	       */
#define ADVERTISE_PAUSE_ASYM	0x0800	/* Try for asymetric pause     */
#define ADVERTISE_RESV		0x1000	/* Unused...		       */
#define ADVERTISE_RFAULT	0x2000	/* Say we can detect faults    */
#define ADVERTISE_LPACK		0x4000	/* Ack link partners response  */
#define ADVERTISE_NPAGE		0x8000	/* Next page bit	       */

#define ADVERTISE_FULL (ADVERTISE_100FULL | ADVERTISE_10FULL | \
			ADVERTISE_CSMA)
#define ADVERTISE_ALL (ADVERTISE_10HALF | ADVERTISE_10FULL | \
		       ADVERTISE_100HALF | ADVERTISE_100FULL)

/* Link partner ability register. */
#define LPA_SLCT		0x001f	/* Same as advertise selector  */
#define LPA_10HALF		0x0020	/* Can do 10mbps half-duplex   */
#define LPA_1000XFULL		0x0020	/* Can do 1000BASE-X full-duplex */
#define LPA_10FULL		0x0040	/* Can do 10mbps full-duplex   */
#define LPA_1000XHALF		0x0040	/* Can do 1000BASE-X half-duplex */
#define LPA_100HALF		0x0080	/* Can do 100mbps half-duplex  */
#define LPA_1000XPAUSE		0x0080	/* Can do 1000BASE-X pause     */
#define LPA_100FULL		0x0100	/* Can do 100mbps full-duplex  */
#define LPA_1000XPAUSE_ASYM	0x0100	/* Can do 1000BASE-X pause asym*/
#define LPA_100BASE4		0x0200	/* Can do 100mbps 4k packets   */
#define LPA_PAUSE_CAP		0x0400	/* Can pause		       */
#define LPA_PAUSE_ASYM		0x0800	/* Can pause asymetrically     */
#define LPA_RESV		0x1000	/* Unused...		       */
#define LPA_RFAULT		0x2000	/* Link partner faulted        */
#define LPA_LPACK		0x4000	/* Link partner acked us       */
#define LPA_NPAGE		0x8000	/* Next page bit	       */

#define LPA_DUPLEX		(LPA_10FULL | LPA_100FULL)
#define LPA_100			(LPA_100FULL | LPA_100HALF | LPA_100BASE4)

/* Expansion register for auto-negotiation. */
#define EXPANSION_NWAY		0x0001	/* Can do N-way auto-nego      */
#define EXPANSION_LCWP		0x0002	/* Got new RX page code word   */
#define EXPANSION_ENABLENPAGE	0x0004	/* This enables npage words    */
#define EXPANSION_NPCAPABLE	0x0008	/* Link partner supports npage */
#define EXPANSION_MFAULTS	0x0010	/* Multiple faults detected    */
#define EXPANSION_RESV		0xffe0	/* Unused...		       */

#define ESTATUS_1000_XFULL	0x8000	/* Can do 1000BX Full */
#define ESTATUS_1000_XHALF	0x4000	/* Can do 1000BX Half */
#define ESTATUS_1000_TFULL	0x2000	/* Can do 1000BT Full */
#define ESTATUS_1000_THALF	0x1000	/* Can do 1000BT Half */

/* N-way test register. */
#define NWAYTEST_RESV1		0x00ff	/* Unused...		       */
#define NWAYTEST_LOOPBACK	0x0100	/* Enable loopback for N-way   */
#define NWAYTEST_RESV2		0xfe00	/* Unused...		       */

/* 1000BASE-T Control register */
#define ADVERTISE_1000FULL	0x0200	/* Advertise 1000BASE-T full duplex */
#define ADVERTISE_1000HALF	0x0100	/* Advertise 1000BASE-T half duplex */

/* 1000BASE-T Status register */
#define LPA_1000LOCALRXOK	0x2000	/* Link partner local receiver status */
#define LPA_1000REMRXOK		0x1000	/* Link partner remote receiver status */
#define LPA_1000FULL		0x0800	/* Link partner 1000BASE-T full duplex */
#define LPA_1000HALF		0x0400	/* Link partner 1000BASE-T half duplex */

/* Flow control flags */
#define FLOW_CTRL_TX		0x01
#define FLOW_CTRL_RX		0x02

/**
 * mii_nway_result
 * @negotiated: value of MII ANAR and'd with ANLPAR
 *
 * Given a set of MII abilities, check each bit and returns the
 * currently supported media, in the priority order defined by
 * IEEE 802.3u.  We use LPA_xxx constants but note this is not the
 * value of LPA solely, as described above.
 *
 * The one exception to IEEE 802.3u is that 100baseT4 is placed
 * between 100T-full and 100T-half.  If your phy does not support
 * 100T4 this is fine. If your phy places 100T4 elsewhere in the
 * priority order, you will need to roll your own function.
 */
static inline unsigned int mii_nway_result (unsigned int negotiated)
{
	unsigned int ret;

	if (negotiated & LPA_100FULL)
		ret = LPA_100FULL;
	else if (negotiated & LPA_100BASE4)
		ret = LPA_100BASE4;
	else if (negotiated & LPA_100HALF)
		ret = LPA_100HALF;
	else if (negotiated & LPA_10FULL)
		ret = LPA_10FULL;
	else
		ret = LPA_10HALF;

	return ret;
}

/**
 * mii_duplex
 * @duplex_lock: Non-zero if duplex is locked at full
 * @negotiated: value of MII ANAR and'd with ANLPAR
 *
 * A small helper function for a common case.  Returns one
 * if the media is operating or locked at full duplex, and
 * returns zero otherwise.
 */
static inline unsigned int mii_duplex (unsigned int duplex_lock,
				       unsigned int negotiated)
{
	if (duplex_lock)
		return 1;
	if (mii_nway_result(negotiated) & LPA_DUPLEX)
		return 1;
	return 0;
}

/**
 * mii_resolve_flowctrl_fdx
 * @lcladv: value of MII ADVERTISE register
 * @rmtadv: value of MII LPA register
 *
 * Resolve full duplex flow control as per IEEE 802.3-2005 table 28B-3
 */
static inline u8 mii_resolve_flowctrl_fdx(u16 lcladv, u16 rmtadv)
{
	u8 cap = 0;

	if (lcladv & rmtadv & ADVERTISE_PAUSE_CAP) {
		cap = FLOW_CTRL_TX | FLOW_CTRL_RX;
	} else if (lcladv & rmtadv & ADVERTISE_PAUSE_ASYM) {
		if (lcladv & ADVERTISE_PAUSE_CAP)
			cap = FLOW_CTRL_RX;
		else if (rmtadv & ADVERTISE_PAUSE_CAP)
			cap = FLOW_CTRL_TX;
	}

	return cap;
}

#endif /* __LINUX_MII_H__ */
Commit	Line	Data
91975b0f HS	1	/*
	2	* linux/mii.h: definitions for MII-compatible transceivers
	3	* Originally drivers/net/sunhme.h.
	4	*
	5	* Copyright (C) 1996, 1999, 2001 David S. Miller (davem@redhat.com)
	6	*/
	7
	8	#ifndef __LINUX_MII_H__
	9	#define __LINUX_MII_H__
	10
	11	/* Generic MII registers. */
	12
d177e444 WD	13	#define MII_BMCR 0x00 /* Basic mode control register */
	14	#define MII_BMSR 0x01 /* Basic mode status register */
	15	#define MII_PHYSID1 0x02 /* PHYS ID 1 */
	16	#define MII_PHYSID2 0x03 /* PHYS ID 2 */
	17	#define MII_ADVERTISE 0x04 /* Advertisement control reg */
	18	#define MII_LPA 0x05 /* Link partner ability reg */
	19	#define MII_EXPANSION 0x06 /* Expansion register */
	20	#define MII_CTRL1000 0x09 /* 1000BASE-T control */
	21	#define MII_STAT1000 0x0a /* 1000BASE-T status */
7ea23555	22	#define MII_ESTATUS 0x0f /* Extended Status */
d177e444 WD	23	#define MII_DCOUNTER 0x12 /* Disconnect counter */
	24	#define MII_FCSCOUNTER 0x13 /* False carrier counter */
	25	#define MII_NWAYTEST 0x14 /* N-way auto-neg test reg */
	26	#define MII_RERRCOUNTER 0x15 /* Receive error counter */
	27	#define MII_SREVISION 0x16 /* Silicon revision */
	28	#define MII_RESV1 0x17 /* Reserved... */
	29	#define MII_LBRERROR 0x18 /* Lpback, rx, bypass error */
	30	#define MII_PHYADDR 0x19 /* PHY address */
	31	#define MII_RESV2 0x1a /* Reserved... */
	32	#define MII_TPISTATUS 0x1b /* TPI status for 10mbps */
	33	#define MII_NCONFIG 0x1c /* Network interface config */
91975b0f HS	34
91975b0f HS	35	/* Basic mode control register. */
d177e444 WD	36	#define BMCR_RESV 0x003f /* Unused... */
	37	#define BMCR_SPEED1000 0x0040 /* MSB of Speed (1000) */
	38	#define BMCR_CTST 0x0080 /* Collision test */
	39	#define BMCR_FULLDPLX 0x0100 /* Full duplex */
	40	#define BMCR_ANRESTART 0x0200 /* Auto negotiation restart */
	41	#define BMCR_ISOLATE 0x0400 /* Disconnect DP83840 from MII */
	42	#define BMCR_PDOWN 0x0800 /* Powerdown the DP83840 */
	43	#define BMCR_ANENABLE 0x1000 /* Enable auto negotiation */
	44	#define BMCR_SPEED100 0x2000 /* Select 100Mbps */
	45	#define BMCR_LOOPBACK 0x4000 /* TXD loopback bits */
	46	#define BMCR_RESET 0x8000 /* Reset the DP83840 */
91975b0f HS	47
91975b0f HS	48	/* Basic mode status register. */
d177e444 WD	49	#define BMSR_ERCAP 0x0001 /* Ext-reg capability */
	50	#define BMSR_JCD 0x0002 /* Jabber detected */
	51	#define BMSR_LSTATUS 0x0004 /* Link status */
	52	#define BMSR_ANEGCAPABLE 0x0008 /* Able to do auto-negotiation */
	53	#define BMSR_RFAULT 0x0010 /* Remote fault detected */
	54	#define BMSR_ANEGCOMPLETE 0x0020 /* Auto-negotiation complete */
	55	#define BMSR_RESV 0x00c0 /* Unused... */
7ea23555	56	#define BMSR_ESTATEN 0x0100 /* Extended Status in R15 */
d177e444 WD	57	#define BMSR_100HALF2 0x0200 /* Can do 100BASE-T2 HDX */
	58	#define BMSR_100FULL2 0x0400 /* Can do 100BASE-T2 FDX */
	59	#define BMSR_10HALF 0x0800 /* Can do 10mbps, half-duplex */
	60	#define BMSR_10FULL 0x1000 /* Can do 10mbps, full-duplex */
	61	#define BMSR_100HALF 0x2000 /* Can do 100mbps, half-duplex */
	62	#define BMSR_100FULL 0x4000 /* Can do 100mbps, full-duplex */
	63	#define BMSR_100BASE4 0x8000 /* Can do 100mbps, 4k packets */
91975b0f HS	64
91975b0f HS	65	/* Advertisement control register. */
d177e444 WD	66	#define ADVERTISE_SLCT 0x001f /* Selector bits */
	67	#define ADVERTISE_CSMA 0x0001 /* Only selector supported */
	68	#define ADVERTISE_10HALF 0x0020 /* Try for 10mbps half-duplex */
	69	#define ADVERTISE_1000XFULL 0x0020 /* Try for 1000BASE-X full-duplex */
	70	#define ADVERTISE_10FULL 0x0040 /* Try for 10mbps full-duplex */
	71	#define ADVERTISE_1000XHALF 0x0040 /* Try for 1000BASE-X half-duplex */
	72	#define ADVERTISE_100HALF 0x0080 /* Try for 100mbps half-duplex */
	73	#define ADVERTISE_1000XPAUSE 0x0080 /* Try for 1000BASE-X pause */
	74	#define ADVERTISE_100FULL 0x0100 /* Try for 100mbps full-duplex */
	75	#define ADVERTISE_1000XPSE_ASYM 0x0100 /* Try for 1000BASE-X asym pause */
	76	#define ADVERTISE_100BASE4 0x0200 /* Try for 100mbps 4k packets */
	77	#define ADVERTISE_PAUSE_CAP 0x0400 /* Try for pause */
	78	#define ADVERTISE_PAUSE_ASYM 0x0800 /* Try for asymetric pause */
	79	#define ADVERTISE_RESV 0x1000 /* Unused... */
	80	#define ADVERTISE_RFAULT 0x2000 /* Say we can detect faults */
	81	#define ADVERTISE_LPACK 0x4000 /* Ack link partners response */
	82	#define ADVERTISE_NPAGE 0x8000 /* Next page bit */
91975b0f HS	83
	84	#define ADVERTISE_FULL (ADVERTISE_100FULL \| ADVERTISE_10FULL \| \
	85	ADVERTISE_CSMA)
	86	#define ADVERTISE_ALL (ADVERTISE_10HALF \| ADVERTISE_10FULL \| \
d177e444	87	ADVERTISE_100HALF \| ADVERTISE_100FULL)
91975b0f HS	88
91975b0f HS	89	/* Link partner ability register. */
d177e444 WD	90	#define LPA_SLCT 0x001f /* Same as advertise selector */
	91	#define LPA_10HALF 0x0020 /* Can do 10mbps half-duplex */
	92	#define LPA_1000XFULL 0x0020 /* Can do 1000BASE-X full-duplex */
	93	#define LPA_10FULL 0x0040 /* Can do 10mbps full-duplex */
	94	#define LPA_1000XHALF 0x0040 /* Can do 1000BASE-X half-duplex */
	95	#define LPA_100HALF 0x0080 /* Can do 100mbps half-duplex */
	96	#define LPA_1000XPAUSE 0x0080 /* Can do 1000BASE-X pause */
	97	#define LPA_100FULL 0x0100 /* Can do 100mbps full-duplex */
	98	#define LPA_1000XPAUSE_ASYM 0x0100 /* Can do 1000BASE-X pause asym*/
	99	#define LPA_100BASE4 0x0200 /* Can do 100mbps 4k packets */
	100	#define LPA_PAUSE_CAP 0x0400 /* Can pause */
	101	#define LPA_PAUSE_ASYM 0x0800 /* Can pause asymetrically */
	102	#define LPA_RESV 0x1000 /* Unused... */
	103	#define LPA_RFAULT 0x2000 /* Link partner faulted */
	104	#define LPA_LPACK 0x4000 /* Link partner acked us */
	105	#define LPA_NPAGE 0x8000 /* Next page bit */
91975b0f HS	106
	107	#define LPA_DUPLEX (LPA_10FULL \| LPA_100FULL)
	108	#define LPA_100 (LPA_100FULL \| LPA_100HALF \| LPA_100BASE4)
	109
	110	/* Expansion register for auto-negotiation. */
d177e444 WD	111	#define EXPANSION_NWAY 0x0001 /* Can do N-way auto-nego */
	112	#define EXPANSION_LCWP 0x0002 /* Got new RX page code word */
	113	#define EXPANSION_ENABLENPAGE 0x0004 /* This enables npage words */
	114	#define EXPANSION_NPCAPABLE 0x0008 /* Link partner supports npage */
	115	#define EXPANSION_MFAULTS 0x0010 /* Multiple faults detected */
	116	#define EXPANSION_RESV 0xffe0 /* Unused... */
7ea23555	117
de1d786e CC	118	#define ESTATUS_1000_XFULL 0x8000 /* Can do 1000BX Full */
de1d786e CC	119	#define ESTATUS_1000_XHALF 0x4000 /* Can do 1000BX Half */
7ea23555 ML	120	#define ESTATUS_1000_TFULL 0x2000 /* Can do 1000BT Full */
7ea23555 ML	121	#define ESTATUS_1000_THALF 0x1000 /* Can do 1000BT Half */
91975b0f HS	122
91975b0f HS	123	/* N-way test register. */
d177e444 WD	124	#define NWAYTEST_RESV1 0x00ff /* Unused... */
	125	#define NWAYTEST_LOOPBACK 0x0100 /* Enable loopback for N-way */
	126	#define NWAYTEST_RESV2 0xfe00 /* Unused... */
7ea23555 ML	127
7ea23555 ML	128	/* 1000BASE-T Control register */
d177e444 WD	129	#define ADVERTISE_1000FULL 0x0200 /* Advertise 1000BASE-T full duplex */
d177e444 WD	130	#define ADVERTISE_1000HALF 0x0100 /* Advertise 1000BASE-T half duplex */
91975b0f	131
7ea23555	132	/* 1000BASE-T Status register */
d177e444 WD	133	#define LPA_1000LOCALRXOK 0x2000 /* Link partner local receiver status */
	134	#define LPA_1000REMRXOK 0x1000 /* Link partner remote receiver status */
	135	#define LPA_1000FULL 0x0800 /* Link partner 1000BASE-T full duplex */
	136	#define LPA_1000HALF 0x0400 /* Link partner 1000BASE-T half duplex */
7ea23555 ML	137
	138	/* Flow control flags */
	139	#define FLOW_CTRL_TX 0x01
	140	#define FLOW_CTRL_RX 0x02
91975b0f HS	141
	142	/**
	143	* mii_nway_result
	144	* @negotiated: value of MII ANAR and'd with ANLPAR
	145	*
	146	* Given a set of MII abilities, check each bit and returns the
	147	* currently supported media, in the priority order defined by
	148	* IEEE 802.3u. We use LPA_xxx constants but note this is not the
	149	* value of LPA solely, as described above.
	150	*
	151	* The one exception to IEEE 802.3u is that 100baseT4 is placed
	152	* between 100T-full and 100T-half. If your phy does not support
7ea23555	153	* 100T4 this is fine. If your phy places 100T4 elsewhere in the
91975b0f HS	154	* priority order, you will need to roll your own function.
	155	*/
	156	static inline unsigned int mii_nway_result (unsigned int negotiated)
	157	{
	158	unsigned int ret;
	159
	160	if (negotiated & LPA_100FULL)
	161	ret = LPA_100FULL;
	162	else if (negotiated & LPA_100BASE4)
	163	ret = LPA_100BASE4;
	164	else if (negotiated & LPA_100HALF)
	165	ret = LPA_100HALF;
	166	else if (negotiated & LPA_10FULL)
	167	ret = LPA_10FULL;
	168	else
	169	ret = LPA_10HALF;
	170
	171	return ret;
	172	}
	173
	174	/**
	175	* mii_duplex
	176	* @duplex_lock: Non-zero if duplex is locked at full
	177	* @negotiated: value of MII ANAR and'd with ANLPAR
	178	*
	179	* A small helper function for a common case. Returns one
	180	* if the media is operating or locked at full duplex, and
	181	* returns zero otherwise.
	182	*/
	183	static inline unsigned int mii_duplex (unsigned int duplex_lock,
	184	unsigned int negotiated)
	185	{
	186	if (duplex_lock)
	187	return 1;
	188	if (mii_nway_result(negotiated) & LPA_DUPLEX)
	189	return 1;
	190	return 0;
	191	}
	192
1c1e3700 YO	193	/**
	194	* mii_resolve_flowctrl_fdx
	195	* @lcladv: value of MII ADVERTISE register
	196	* @rmtadv: value of MII LPA register
	197	*
	198	* Resolve full duplex flow control as per IEEE 802.3-2005 table 28B-3
	199	*/
	200	static inline u8 mii_resolve_flowctrl_fdx(u16 lcladv, u16 rmtadv)
	201	{
	202	u8 cap = 0;
	203
	204	if (lcladv & rmtadv & ADVERTISE_PAUSE_CAP) {
	205	cap = FLOW_CTRL_TX \| FLOW_CTRL_RX;
	206	} else if (lcladv & rmtadv & ADVERTISE_PAUSE_ASYM) {
	207	if (lcladv & ADVERTISE_PAUSE_CAP)
	208	cap = FLOW_CTRL_RX;
	209	else if (rmtadv & ADVERTISE_PAUSE_CAP)
	210	cap = FLOW_CTRL_TX;
	211	}
	212
	213	return cap;
	214	}
	215
91975b0f	216	#endif /* __LINUX_MII_H__ */