[people/ms/u-boot.git] / include / ns87308.h

/*
 * (C) Copyright 2000
 * Rob Taylor, Flying Pig Systems. robt@flyingpig.com.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef _NS87308_H_
#define _NS87308_H_

#include <asm/pci_io.h>

/* Note: I couldn't find a full data sheet for the ns87308, but the ns87307 seems to be pretty
   functionally- (and pin-) equivalent to the 87308, but the 308 has better ir support. */

void initialise_ns87308(void);

/*
 * The following struct represents the GPIO registers on the NS87308/NS97307
 */
struct GPIO
{
  unsigned char dta1;  /* 0 data port 1 */
  unsigned char dir1;  /* 1 direction port 1 */
  unsigned char out1;  /* 2 output type port 1 */
  unsigned char puc1;  /* 3 pull-up control port 1 */
  unsigned char dta2;  /* 4 data port 2 */
  unsigned char dir2;  /* 5 direction port 2 */
  unsigned char out2;  /* 6 output type port 2 */
  unsigned char puc2;  /* 7 pull-up control port 2  */
};

/*
 * The following represents the power management registers on the NS87308/NS97307
 */
#define PWM_FER1 0  /* 0 function enable reg. 1 */
#define PWM_FER2 1  /* 1 function enable reg. 2 */
#define PWM_PMC1 2  /* 2 power mgmt. control 1 */
#define PWM_PMC2 3  /* 3 power mgmt. control 2 */
#define PWM_PMC3 4  /* 4 power mgmt. control 3 */
#define PWM_WDTO 5  /* 5 watchdog time-out */
#define PWM_WDCF 6  /* 6 watchdog config. */
#define PWM_WDST 7  /* 7 watchdog status  */

/*PNP config registers:
 * these depend on the stated of BADDR1 and BADDR0 on startup
 * so there's three versions here with the last two digits indicating
 * for which configuration their valid
 * the 1st of the two digits indicates the state of BADDR1
 * the 2st of the two digits indicates the state of BADDR0
 */


#define IO_INDEX_OFFSET_0x 0x0279  /* full PnP isa Mode */
#define IO_INDEX_OFFSET_10 0x015C  /* PnP motherboard mode */
#define IO_INDEX_OFFSET_11 0x002E  /* PnP motherboard mode */
#define IO_DATA_OFFSET_0x  0x0A79  /* full PnP isa Mode */
#define IO_DATA_OFFSET_10  0x015D  /* PnP motherboard mode */
#define IO_DATA_OFFSET_11  0x002F  /* PnP motherboard mode */

#if defined(CONFIG_SYS_NS87308_BADDR_0x)
#define IO_INDEX (CONFIG_SYS_ISA_IO + IO_INDEX_OFFSET_0x)
#define IO_DATA  (CONFIG_SYS_ISA_IO + IO_DATA_OFFSET_0x)
#elif defined(CONFIG_SYS_NS87308_BADDR_10)
#define IO_INDEX (CONFIG_SYS_ISA_IO + IO_INDEX_OFFSET_10)
#define IO_DATA  (CONFIG_SYS_ISA_IO + IO_DATA_OFFSET_10)
#elif defined(CONFIG_SYS_NS87308_BADDR_11)
#define IO_INDEX (CONFIG_SYS_ISA_IO + IO_INDEX_OFFSET_11)
#define IO_DATA  (CONFIG_SYS_ISA_IO + IO_DATA_OFFSET_11)
#endif

/* PnP register definitions */

#define SET_RD_DATA_PORT    0x00
#define SERIAL_ISOLATION    0x01
#define CONFIG_CONTROL      0x02
#define WAKE_CSN            0x03
#define RES_DATA            0x04
#define STATUS              0x05
#define SET_CSN             0x06
#define LOGICAL_DEVICE      0x07

/*vendor defined values */
#define SID_REG             0x20
#define SUPOERIO_CONF1      0x21
#define SUPOERIO_CONF2      0x22
#define PGCS_INDEX          0x23
#define PGCS_DATA           0x24

/* values above 30 are different for each logical device
   but I can't be arsed to enter them all. the ones here
   are pretty consistent between all logical devices
   feel free to correct the situation if you want.. ;)
   */
#define ACTIVATE            0x30
#define ACTIVATE_OFF        0x00
#define ACTIVATE_ON         0x01

#define BASE_ADDR_HIGH      0x60
#define BASE_ADDR_LOW       0x61
#define LUN_CONFIG_REG		0xF0
#define DBASE_HIGH			0x60	/* SIO KBC data base address, 15:8 */
#define DBASE_LOW			0x61	/* SIO KBC data base address,  7:0 */
#define CBASE_HIGH			0x62	/* SIO KBC command base addr, 15:8 */
#define CBASE_LOW			0x63	/* SIO KBC command base addr,  7:0 */

/* the logical devices*/
#define LDEV_KBC1           0x00	/* 2 devices for keyboard and mouse controller*/
#define LDEV_KBC2           0x01
#define LDEV_MOUSE          0x01
#define LDEV_RTC_APC        0x02	/*Real Time Clock and Advanced Power Control*/
#define LDEV_FDC            0x03	/*floppy disk controller*/
#define LDEV_PARP           0x04	/*Parallel port*/
#define LDEV_UART2          0x05
#define LDEV_UART1          0x06
#define LDEV_GPIO           0x07    /*General Purpose IO and chip select output signals*/
#define LDEV_POWRMAN        0x08    /*Power Managment*/

#define CONFIG_SYS_NS87308_KBC1	(1 << LDEV_KBC1)
#define CONFIG_SYS_NS87308_KBC2	(1 << LDEV_KBC2)
#define CONFIG_SYS_NS87308_MOUSE	(1 << LDEV_MOUSE)
#define CONFIG_SYS_NS87308_RTC_APC	(1 << LDEV_RTC_APC)
#define CONFIG_SYS_NS87308_FDC		(1 << LDEV_FDC)
#define CONFIG_SYS_NS87308_PARP	(1 << LDEV_PARP)
#define CONFIG_SYS_NS87308_UART2	(1 << LDEV_UART2)
#define CONFIG_SYS_NS87308_UART1	(1 << LDEV_UART1)
#define CONFIG_SYS_NS87308_GPIO	(1 << LDEV_GPIO)
#define CONFIG_SYS_NS87308_POWRMAN	(1 << LDEV_POWRMAN)

/*some functions and macro's for doing configuration */

static inline void read_pnp_config(unsigned char index, unsigned char *data)
{
    pci_writeb(index,IO_INDEX);
    pci_readb(IO_DATA, *data);
}

static inline void write_pnp_config(unsigned char index, unsigned char data)
{
    pci_writeb(index,IO_INDEX);
    pci_writeb(data, IO_DATA);
}

static inline void pnp_set_device(unsigned char dev)
{
    write_pnp_config(LOGICAL_DEVICE, dev);
}

static inline void write_pm_reg(unsigned short base, unsigned char index, unsigned char data)
{
    pci_writeb(index, CONFIG_SYS_ISA_IO + base);
    eieio();
    pci_writeb(data, CONFIG_SYS_ISA_IO + base + 1);
}

/*void write_pnp_config(unsigned char index, unsigned char data);
void pnp_set_device(unsigned char dev);
*/

#define PNP_SET_DEVICE_BASE(dev,base) \
   pnp_set_device(dev); \
   write_pnp_config(ACTIVATE, ACTIVATE_OFF); \
   write_pnp_config(BASE_ADDR_HIGH, ((base) >> 8) & 0xff ); \
   write_pnp_config(BASE_ADDR_LOW, (base) &0xff); \
   write_pnp_config(ACTIVATE, ACTIVATE_ON);

#define PNP_ACTIVATE_DEVICE(dev) \
   pnp_set_device(dev); \
   write_pnp_config(ACTIVATE, ACTIVATE_ON);

#define PNP_DEACTIVATE_DEVICE(dev) \
   pnp_set_device(dev); \
   write_pnp_config(ACTIVATE, ACTIVATE_OFF);


static inline void write_pgcs_config(unsigned char index, unsigned char data)
{
    write_pnp_config(PGCS_INDEX, index);
    write_pnp_config(PGCS_DATA, data);
}

/* these macrose configure the 3 CS lines
   on the sandpoint board these controll NVRAM
   CS0 is connected to NVRAMCS
   CS1 is connected to NVRAMAS0
   CS2 is connected to NVRAMAS1
   */
#define PGCS_CS_ASSERT_ON_WRITE 0x10
#define PGCS_CS_ASSERT_ON_READ  0x20

#define PNP_PGCS_CSLINE_BASE(cs, base) \
  write_pgcs_config((cs) << 2, ((base) >> 8) & 0xff ); \
  write_pgcs_config(((cs) << 2) + 1, (base) & 0xff );

#define PNP_PGCS_CSLINE_CONF(cs, conf) \
  write_pgcs_config(((cs) << 2) + 2, (conf) );


/* The following sections are for 87308 extensions to the standard compoents it emulates */

/* extensions to 16550*/

#define MCR_MDSL_MSK    0xe0 /*mode select mask*/
#define MCR_MDSL_UART   0x00 /*uart, default*/
#define MCR_MDSL_SHRPIR 0x02 /*Sharp IR*/
#define MCR_MDSL_SIR    0x03 /*SIR*/
#define MCR_MDSL_CIR    0x06 /*Consumer IR*/

#define FCR_TXFTH0      0x10    /* these bits control threshod of data level in fifo */
#define FCR_TXFTH1      0x20    /* for interrupt trigger */

/*
 * Default NS87308 configuration
 */
#ifndef CONFIG_SYS_NS87308_KBC1_BASE
#define CONFIG_SYS_NS87308_KBC1_BASE	0x0060
#endif
#ifndef CONFIG_SYS_NS87308_RTC_BASE
#define CONFIG_SYS_NS87308_RTC_BASE	0x0070
#endif
#ifndef CONFIG_SYS_NS87308_FDC_BASE
#define CONFIG_SYS_NS87308_FDC_BASE	0x03F0
#endif
#ifndef CONFIG_SYS_NS87308_LPT_BASE
#define CONFIG_SYS_NS87308_LPT_BASE	0x0278
#endif
#ifndef CONFIG_SYS_NS87308_UART1_BASE
#define CONFIG_SYS_NS87308_UART1_BASE	0x03F8
#endif
#ifndef CONFIG_SYS_NS87308_UART2_BASE
#define CONFIG_SYS_NS87308_UART2_BASE	0x02F8
#endif

#endif /*_NS87308_H_*/
Commit	Line	Data
e85390dc WD	1	/*
	2	* (C) Copyright 2000
	3	* Rob Taylor, Flying Pig Systems. robt@flyingpig.com.
	4	*
1a459660	5	* SPDX-License-Identifier: GPL-2.0+
e85390dc WD	6	*/
	7
	8	#ifndef _NS87308_H_
	9	#define _NS87308_H_
	10
	11	#include <asm/pci_io.h>
	12
	13	/* Note: I couldn't find a full data sheet for the ns87308, but the ns87307 seems to be pretty
	14	functionally- (and pin-) equivalent to the 87308, but the 308 has better ir support. */
	15
	16	void initialise_ns87308(void);
	17
	18	/*
	19	* The following struct represents the GPIO registers on the NS87308/NS97307
	20	*/
	21	struct GPIO
	22	{
	23	unsigned char dta1; /* 0 data port 1 */
	24	unsigned char dir1; /* 1 direction port 1 */
	25	unsigned char out1; /* 2 output type port 1 */
	26	unsigned char puc1; /* 3 pull-up control port 1 */
	27	unsigned char dta2; /* 4 data port 2 */
	28	unsigned char dir2; /* 5 direction port 2 */
	29	unsigned char out2; /* 6 output type port 2 */
	30	unsigned char puc2; /* 7 pull-up control port 2 */
	31	};
	32
	33	/*
	34	* The following represents the power management registers on the NS87308/NS97307
	35	*/
	36	#define PWM_FER1 0 /* 0 function enable reg. 1 */
	37	#define PWM_FER2 1 /* 1 function enable reg. 2 */
	38	#define PWM_PMC1 2 /* 2 power mgmt. control 1 */
	39	#define PWM_PMC2 3 /* 3 power mgmt. control 2 */
	40	#define PWM_PMC3 4 /* 4 power mgmt. control 3 */
	41	#define PWM_WDTO 5 /* 5 watchdog time-out */
	42	#define PWM_WDCF 6 /* 6 watchdog config. */
	43	#define PWM_WDST 7 /* 7 watchdog status */
	44
	45	/*PNP config registers:
	46	* these depend on the stated of BADDR1 and BADDR0 on startup
	47	* so there's three versions here with the last two digits indicating
	48	* for which configuration their valid
	49	* the 1st of the two digits indicates the state of BADDR1
	50	* the 2st of the two digits indicates the state of BADDR0
	51	*/
	52
	53
	54	#define IO_INDEX_OFFSET_0x 0x0279 /* full PnP isa Mode */
	55	#define IO_INDEX_OFFSET_10 0x015C /* PnP motherboard mode */
	56	#define IO_INDEX_OFFSET_11 0x002E /* PnP motherboard mode */
	57	#define IO_DATA_OFFSET_0x 0x0A79 /* full PnP isa Mode */
	58	#define IO_DATA_OFFSET_10 0x015D /* PnP motherboard mode */
	59	#define IO_DATA_OFFSET_11 0x002F /* PnP motherboard mode */
	60
6d0f6bcf JCPV	61	#if defined(CONFIG_SYS_NS87308_BADDR_0x)
	62	#define IO_INDEX (CONFIG_SYS_ISA_IO + IO_INDEX_OFFSET_0x)
	63	#define IO_DATA (CONFIG_SYS_ISA_IO + IO_DATA_OFFSET_0x)
	64	#elif defined(CONFIG_SYS_NS87308_BADDR_10)
	65	#define IO_INDEX (CONFIG_SYS_ISA_IO + IO_INDEX_OFFSET_10)
	66	#define IO_DATA (CONFIG_SYS_ISA_IO + IO_DATA_OFFSET_10)
	67	#elif defined(CONFIG_SYS_NS87308_BADDR_11)
	68	#define IO_INDEX (CONFIG_SYS_ISA_IO + IO_INDEX_OFFSET_11)
	69	#define IO_DATA (CONFIG_SYS_ISA_IO + IO_DATA_OFFSET_11)
e85390dc WD	70	#endif
	71
	72	/* PnP register definitions */
	73
	74	#define SET_RD_DATA_PORT 0x00
	75	#define SERIAL_ISOLATION 0x01
	76	#define CONFIG_CONTROL 0x02
	77	#define WAKE_CSN 0x03
	78	#define RES_DATA 0x04
	79	#define STATUS 0x05
	80	#define SET_CSN 0x06
	81	#define LOGICAL_DEVICE 0x07
	82
	83	/vendor defined values /
	84	#define SID_REG 0x20
	85	#define SUPOERIO_CONF1 0x21
	86	#define SUPOERIO_CONF2 0x22
	87	#define PGCS_INDEX 0x23
	88	#define PGCS_DATA 0x24
	89
	90	/* values above 30 are different for each logical device
	91	but I can't be arsed to enter them all. the ones here
	92	are pretty consistent between all logical devices
	93	feel free to correct the situation if you want.. ;)
	94	*/
	95	#define ACTIVATE 0x30
	96	#define ACTIVATE_OFF 0x00
	97	#define ACTIVATE_ON 0x01
	98
	99	#define BASE_ADDR_HIGH 0x60
	100	#define BASE_ADDR_LOW 0x61
	101	#define LUN_CONFIG_REG 0xF0
	102	#define DBASE_HIGH 0x60 /* SIO KBC data base address, 15:8 */
	103	#define DBASE_LOW 0x61 /* SIO KBC data base address, 7:0 */
	104	#define CBASE_HIGH 0x62 /* SIO KBC command base addr, 15:8 */
	105	#define CBASE_LOW 0x63 /* SIO KBC command base addr, 7:0 */
	106
	107	/* the logical devices*/
	108	#define LDEV_KBC1 0x00 /* 2 devices for keyboard and mouse controller*/
	109	#define LDEV_KBC2 0x01
	110	#define LDEV_MOUSE 0x01
	111	#define LDEV_RTC_APC 0x02 /Real Time Clock and Advanced Power Control/
	112	#define LDEV_FDC 0x03 /floppy disk controller/
	113	#define LDEV_PARP 0x04 /Parallel port/
	114	#define LDEV_UART2 0x05
	115	#define LDEV_UART1 0x06
	116	#define LDEV_GPIO 0x07 /General Purpose IO and chip select output signals/
	117	#define LDEV_POWRMAN 0x08 /Power Managment/
	118
6d0f6bcf JCPV	119	#define CONFIG_SYS_NS87308_KBC1 (1 << LDEV_KBC1)
	120	#define CONFIG_SYS_NS87308_KBC2 (1 << LDEV_KBC2)
	121	#define CONFIG_SYS_NS87308_MOUSE (1 << LDEV_MOUSE)
	122	#define CONFIG_SYS_NS87308_RTC_APC (1 << LDEV_RTC_APC)
	123	#define CONFIG_SYS_NS87308_FDC (1 << LDEV_FDC)
	124	#define CONFIG_SYS_NS87308_PARP (1 << LDEV_PARP)
	125	#define CONFIG_SYS_NS87308_UART2 (1 << LDEV_UART2)
	126	#define CONFIG_SYS_NS87308_UART1 (1 << LDEV_UART1)
	127	#define CONFIG_SYS_NS87308_GPIO (1 << LDEV_GPIO)
	128	#define CONFIG_SYS_NS87308_POWRMAN (1 << LDEV_POWRMAN)
e85390dc WD	129
	130	/some functions and macro's for doing configuration /
	131
	132	static inline void read_pnp_config(unsigned char index, unsigned char *data)
	133	{
	134	pci_writeb(index,IO_INDEX);
	135	pci_readb(IO_DATA, *data);
	136	}
	137
	138	static inline void write_pnp_config(unsigned char index, unsigned char data)
	139	{
	140	pci_writeb(index,IO_INDEX);
	141	pci_writeb(data, IO_DATA);
	142	}
	143
	144	static inline void pnp_set_device(unsigned char dev)
	145	{
	146	write_pnp_config(LOGICAL_DEVICE, dev);
	147	}
	148
	149	static inline void write_pm_reg(unsigned short base, unsigned char index, unsigned char data)
	150	{
6d0f6bcf	151	pci_writeb(index, CONFIG_SYS_ISA_IO + base);
e85390dc	152	eieio();
6d0f6bcf	153	pci_writeb(data, CONFIG_SYS_ISA_IO + base + 1);
e85390dc WD	154	}
	155
	156	/*void write_pnp_config(unsigned char index, unsigned char data);
	157	void pnp_set_device(unsigned char dev);
	158	*/
	159
	160	#define PNP_SET_DEVICE_BASE(dev,base) \
	161	pnp_set_device(dev); \
	162	write_pnp_config(ACTIVATE, ACTIVATE_OFF); \
	163	write_pnp_config(BASE_ADDR_HIGH, ((base) >> 8) & 0xff ); \
	164	write_pnp_config(BASE_ADDR_LOW, (base) &0xff); \
	165	write_pnp_config(ACTIVATE, ACTIVATE_ON);
	166
	167	#define PNP_ACTIVATE_DEVICE(dev) \
	168	pnp_set_device(dev); \
	169	write_pnp_config(ACTIVATE, ACTIVATE_ON);
	170
	171	#define PNP_DEACTIVATE_DEVICE(dev) \
	172	pnp_set_device(dev); \
	173	write_pnp_config(ACTIVATE, ACTIVATE_OFF);
	174
	175
	176	static inline void write_pgcs_config(unsigned char index, unsigned char data)
	177	{
	178	write_pnp_config(PGCS_INDEX, index);
	179	write_pnp_config(PGCS_DATA, data);
	180	}
	181
	182	/* these macrose configure the 3 CS lines
	183	on the sandpoint board these controll NVRAM
	184	CS0 is connected to NVRAMCS
	185	CS1 is connected to NVRAMAS0
	186	CS2 is connected to NVRAMAS1
	187	*/
	188	#define PGCS_CS_ASSERT_ON_WRITE 0x10
	189	#define PGCS_CS_ASSERT_ON_READ 0x20
	190
	191	#define PNP_PGCS_CSLINE_BASE(cs, base) \
	192	write_pgcs_config((cs) << 2, ((base) >> 8) & 0xff ); \
	193	write_pgcs_config(((cs) << 2) + 1, (base) & 0xff );
	194
	195	#define PNP_PGCS_CSLINE_CONF(cs, conf) \
	196	write_pgcs_config(((cs) << 2) + 2, (conf) );
	197
	198
	199	/* The following sections are for 87308 extensions to the standard compoents it emulates */
	200
	201	/* extensions to 16550*/
	202
	203	#define MCR_MDSL_MSK 0xe0 /mode select mask/
	204	#define MCR_MDSL_UART 0x00 /uart, default/
	205	#define MCR_MDSL_SHRPIR 0x02 /Sharp IR/
	206	#define MCR_MDSL_SIR 0x03 /SIR/
	207	#define MCR_MDSL_CIR 0x06 /Consumer IR/
	208
	209	#define FCR_TXFTH0 0x10 /* these bits control threshod of data level in fifo */
	210	#define FCR_TXFTH1 0x20 /* for interrupt trigger */
	211
	212	/*
	213	* Default NS87308 configuration
	214	*/
6d0f6bcf JCPV	215	#ifndef CONFIG_SYS_NS87308_KBC1_BASE
6d0f6bcf JCPV	216	#define CONFIG_SYS_NS87308_KBC1_BASE 0x0060
e85390dc	217	#endif
6d0f6bcf JCPV	218	#ifndef CONFIG_SYS_NS87308_RTC_BASE
6d0f6bcf JCPV	219	#define CONFIG_SYS_NS87308_RTC_BASE 0x0070
e85390dc	220	#endif
6d0f6bcf JCPV	221	#ifndef CONFIG_SYS_NS87308_FDC_BASE
6d0f6bcf JCPV	222	#define CONFIG_SYS_NS87308_FDC_BASE 0x03F0
e85390dc	223	#endif
6d0f6bcf JCPV	224	#ifndef CONFIG_SYS_NS87308_LPT_BASE
6d0f6bcf JCPV	225	#define CONFIG_SYS_NS87308_LPT_BASE 0x0278
e85390dc	226	#endif
6d0f6bcf JCPV	227	#ifndef CONFIG_SYS_NS87308_UART1_BASE
6d0f6bcf JCPV	228	#define CONFIG_SYS_NS87308_UART1_BASE 0x03F8
e85390dc	229	#endif
6d0f6bcf JCPV	230	#ifndef CONFIG_SYS_NS87308_UART2_BASE
6d0f6bcf JCPV	231	#define CONFIG_SYS_NS87308_UART2_BASE 0x02F8
e85390dc WD	232	#endif
	233
	234	#endif /_NS87308_H_/