[people/ms/u-boot.git] / include / tps6586x.h

/*
 *  (C) Copyright 2010,2011
 *  NVIDIA Corporation <www.nvidia.com>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef _TPS6586X_H_
#define _TPS6586X_H_

enum {
	/* SM0-2 PWM/PFM Mode Selection */
	TPS6586X_PWM_SM0	= 1 << 0,
	TPS6586X_PWM_SM1	= 1 << 1,
	TPS6586X_PWM_SM2	= 1 << 2,
};

/**
 * Enable PWM mode for selected SM0-2
 *
 * @param mask	Mask of synchronous converter to enable (TPS6586X_PWM_...)
 * @return 0 if ok, -1 on error
 */
int tps6586x_set_pwm_mode(int mask);

/**
 * Adjust SM0 and SM1 voltages to the given targets in incremental steps.
 *
 * @param sm0_target	Target voltage for SM0 in 25mW units, 0=725mV, 31=1.5V
 * @param sm1_target	Target voltage for SM1 in 25mW units, 0=725mV, 31=1.5V
 * @param step		Amount to change voltage in each step, in 25mW units
 * @param rate		Slew ratein mV/us: 0=instantly, 1=0.11, 2=0.22,
 *			3=0.44, 4=0.88, 5=1.76, 6=3.52, 7=7.04
 * @param min_sm0_over_sm1	Minimum amount by which sm0 must exceed sm1.
 *			If this condition is not met, no adjustment will be
 *			done and an error will be reported. Use -1 to skip
 *			this check.
 * @return 0 if ok, -1 on error
 */
int tps6586x_adjust_sm0_sm1(int sm0_target, int sm1_target, int step, int rate,
			    int min_sm0_over_sm1);

/**
 * Set up the TPS6586X I2C bus number. This will be used for all operations
 * on the device. This function must be called before using other functions.
 *
 * @param bus	I2C bus containing the TPS6586X chip
 * @return 0 (always succeeds)
 */
int tps6586x_init(struct udevice *bus);

#endif	/* _TPS6586X_H_ */
Commit	Line	Data
1aa7e23e SG	1	/*
	2	* (C) Copyright 2010,2011
	3	* NVIDIA Corporation <www.nvidia.com>
	4	*
1a459660	5	* SPDX-License-Identifier: GPL-2.0+
1aa7e23e SG	6	*/
1aa7e23e SG	7
7ffdc831	8	#ifndef _TPS6586X_H_
1aa7e23e SG	9	#define _TPS6586X_H_
	10
	11	enum {
	12	/* SM0-2 PWM/PFM Mode Selection */
	13	TPS6586X_PWM_SM0 = 1 << 0,
	14	TPS6586X_PWM_SM1 = 1 << 1,
	15	TPS6586X_PWM_SM2 = 1 << 2,
	16	};
	17
	18	/**
	19	* Enable PWM mode for selected SM0-2
	20	*
	21	* @param mask Mask of synchronous converter to enable (TPS6586X_PWM_...)
	22	* @return 0 if ok, -1 on error
	23	*/
	24	int tps6586x_set_pwm_mode(int mask);
	25
	26	/**
	27	* Adjust SM0 and SM1 voltages to the given targets in incremental steps.
	28	*
	29	* @param sm0_target Target voltage for SM0 in 25mW units, 0=725mV, 31=1.5V
	30	* @param sm1_target Target voltage for SM1 in 25mW units, 0=725mV, 31=1.5V
	31	* @param step Amount to change voltage in each step, in 25mW units
	32	* @param rate Slew ratein mV/us: 0=instantly, 1=0.11, 2=0.22,
	33	* 3=0.44, 4=0.88, 5=1.76, 6=3.52, 7=7.04
	34	* @param min_sm0_over_sm1 Minimum amount by which sm0 must exceed sm1.
	35	* If this condition is not met, no adjustment will be
	36	* done and an error will be reported. Use -1 to skip
	37	* this check.
	38	* @return 0 if ok, -1 on error
	39	*/
	40	int tps6586x_adjust_sm0_sm1(int sm0_target, int sm1_target, int step, int rate,
	41	int min_sm0_over_sm1);
	42
	43	/**
	44	* Set up the TPS6586X I2C bus number. This will be used for all operations
	45	* on the device. This function must be called before using other functions.
	46	*
b0e6ef46	47	* @param bus I2C bus containing the TPS6586X chip
1aa7e23e SG	48	* @return 0 (always succeeds)
1aa7e23e SG	49	*/
b0e6ef46	50	int tps6586x_init(struct udevice *bus);
1aa7e23e SG	51
1aa7e23e SG	52	#endif /* _TPS6586X_H_ */