[people/ms/u-boot.git] / include / configs / BSC9131RDB.h

/*
 * Copyright 2011-2012 Freescale Semiconductor, Inc.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

/*
 * BSC9131 RDB board configuration file
 */

#ifndef __CONFIG_H
#define __CONFIG_H

#define CONFIG_NAND_FSL_IFC

#ifdef CONFIG_SPIFLASH
#define CONFIG_RAMBOOT_SPIFLASH
#define CONFIG_SYS_RAMBOOT
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_SYS_TEXT_BASE		0x11000000
#define CONFIG_RESET_VECTOR_ADDRESS	0x110bfffc
#endif

#ifdef CONFIG_NAND
#define CONFIG_SPL_INIT_MINIMAL
#define CONFIG_SPL_NAND_BOOT
#define CONFIG_SPL_FLUSH_IMAGE
#define CONFIG_SPL_TARGET		"u-boot-with-spl.bin"

#define CONFIG_SYS_TEXT_BASE		0x00201000
#define CONFIG_SPL_TEXT_BASE		0xFFFFE000
#define CONFIG_SPL_MAX_SIZE		8192
#define CONFIG_SPL_RELOC_TEXT_BASE	0x00100000
#define CONFIG_SPL_RELOC_STACK		0x00100000
#define CONFIG_SYS_NAND_U_BOOT_SIZE	((768 << 10) - 0x2000)
#define CONFIG_SYS_NAND_U_BOOT_DST	(0x00200000 - CONFIG_SPL_MAX_SIZE)
#define CONFIG_SYS_NAND_U_BOOT_START	0x00200000
#define CONFIG_SYS_NAND_U_BOOT_OFFS	0
#define CONFIG_SYS_LDSCRIPT	"arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
#endif

#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MONITOR_BASE	CONFIG_SPL_TEXT_BASE
#else
#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
#endif

/* High Level Configuration Options */
#define CONFIG_FSL_CAAM			/* Enable SEC/CAAM */

#define CONFIG_TSEC_ENET
#define CONFIG_ENV_OVERWRITE

#define CONFIG_DDR_CLK_FREQ	66666666 /* DDRCLK on 9131 RDB */
#if defined(CONFIG_SYS_CLK_100)
#define CONFIG_SYS_CLK_FREQ    100000000 /* SYSCLK for 9131 RDB */
#else
#define CONFIG_SYS_CLK_FREQ	66666666 /* SYSCLK for 9131 RDB */
#endif

#define CONFIG_HWCONFIG
/*
 * These can be toggled for performance analysis, otherwise use default.
 */
#define CONFIG_L2_CACHE			/* toggle L2 cache */
#define CONFIG_BTB			/* enable branch predition */

#define CONFIG_SYS_MEMTEST_START	0x01000000	/* memtest works on */
#define CONFIG_SYS_MEMTEST_END		0x01ffffff

/* DDR Setup */
#undef CONFIG_SYS_DDR_RAW_TIMING
#undef CONFIG_DDR_SPD
#define CONFIG_SYS_SPD_BUS_NUM		0
#define SPD_EEPROM_ADDRESS		0x52 /* I2C access */

#define CONFIG_MEM_INIT_VALUE		0xDeadBeef

#ifndef __ASSEMBLY__
extern unsigned long get_sdram_size(void);
#endif
#define CONFIG_SYS_SDRAM_SIZE		get_sdram_size() /* DDR size */
#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE

#define CONFIG_DIMM_SLOTS_PER_CTLR	1
#define CONFIG_CHIP_SELECTS_PER_CTRL	1

#define CONFIG_SYS_DDR_CS0_BNDS		0x0000003f
#define CONFIG_SYS_DDR_CS0_CONFIG	0x80014302
#define CONFIG_SYS_DDR_CS0_CONFIG_2	0x00000000

#define CONFIG_SYS_DDR_DATA_INIT	0xdeadbeef
#define CONFIG_SYS_DDR_INIT_ADDR	0x00000000
#define CONFIG_SYS_DDR_INIT_EXT_ADDR	0x00000000
#define CONFIG_SYS_DDR_MODE_CONTROL	0x00000000

#define CONFIG_SYS_DDR_ZQ_CONTROL	0x89080600
#define CONFIG_SYS_DDR_SR_CNTR		0x00000000
#define CONFIG_SYS_DDR_RCW_1		0x00000000
#define CONFIG_SYS_DDR_RCW_2		0x00000000
#define CONFIG_SYS_DDR_CONTROL		0xC70C0000	/* Type = DDR3	*/
#define CONFIG_SYS_DDR_CONTROL_2	0x24401000
#define CONFIG_SYS_DDR_TIMING_4		0x00000001
#define CONFIG_SYS_DDR_TIMING_5		0x02401400

#define CONFIG_SYS_DDR_TIMING_3_800		0x00030000
#define CONFIG_SYS_DDR_TIMING_0_800		0x00110104
#define CONFIG_SYS_DDR_TIMING_1_800		0x6f6b8644
#define CONFIG_SYS_DDR_TIMING_2_800		0x0fa888cf
#define CONFIG_SYS_DDR_CLK_CTRL_800		0x03000000
#define CONFIG_SYS_DDR_MODE_1_800		0x00441420
#define CONFIG_SYS_DDR_MODE_2_800		0x8000c000
#define CONFIG_SYS_DDR_INTERVAL_800		0x0c300100
#define CONFIG_SYS_DDR_WRLVL_CONTROL_800	0x8675f608

/*
 * Base addresses -- Note these are effective addresses where the
 * actual resources get mapped (not physical addresses)
 */
/* relocated CCSRBAR */
#define CONFIG_SYS_CCSRBAR	CONFIG_SYS_CCSRBAR_DEFAULT
#define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR_DEFAULT

#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses */
							/* CONFIG_SYS_IMMR */
/* DSP CCSRBAR */
#define CONFIG_SYS_FSL_DSP_CCSRBAR	CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
#define CONFIG_SYS_FSL_DSP_CCSRBAR_PHYS	CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT

/*
 * Memory map
 *
 * 0x0000_0000	0x3FFF_FFFF	DDR			1G cacheable
 * 0x8800_0000	0x8810_0000	IFC internal SRAM		1M
 * 0xB000_0000	0xB0FF_FFFF	DSP core M2 memory	16M
 * 0xC100_0000	0xC13F_FFFF	MAPLE-2F		4M
 * 0xC1F0_0000	0xC1F3_FFFF	PA L2 SRAM Region 0	256K
 * 0xC1F8_0000	0xC1F9_FFFF	PA L2 SRAM Region 1	128K
 * 0xFED0_0000	0xFED0_3FFF	SEC Secured RAM		16K
 * 0xFF60_0000	0xFF6F_FFFF	DSP CCSR		1M
 * 0xFF70_0000	0xFF7F_FFFF	PA CCSR			1M
 * 0xFF80_0000	0xFFFF_FFFF	Boot Page & NAND flash buffer	8M
 *
 */

/*
 * IFC Definitions
 */

/* NAND Flash on IFC */
#define CONFIG_SYS_NAND_BASE		0xff800000
#define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE

#define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
				| CSPR_PORT_SIZE_8	/* Port Size = 8 bit*/ \
				| CSPR_MSEL_NAND	/* MSEL = NAND */ \
				| CSPR_V)
#define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64*1024)

#define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
				| CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
				| CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
				| CSOR_NAND_RAL_2	/* RAL = 2Byes */ \
				| CSOR_NAND_PGS_2K	/* Page Size = 2K */ \
				| CSOR_NAND_SPRZ_64	/* Spare size = 64 */ \
				| CSOR_NAND_PB(64))	/*Pages Per Block = 64*/

/* NAND Flash Timing Params */
#define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x03)  \
					| FTIM0_NAND_TWP(0x05)   \
					| FTIM0_NAND_TWCHT(0x02) \
					| FTIM0_NAND_TWH(0x04))
#define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x1C) \
					| FTIM1_NAND_TWBE(0x1E) \
					| FTIM1_NAND_TRR(0x07)  \
					| FTIM1_NAND_TRP(0x05))
#define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0x08)  \
					| FTIM2_NAND_TREH(0x04) \
					| FTIM2_NAND_TWHRE(0x11))
#define CONFIG_SYS_NAND_FTIM3		FTIM3_NAND_TWW(0x04)

#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE	1
#define CONFIG_CMD_NAND
#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)

#define CONFIG_SYS_NAND_DDR_LAW		11

/* Set up IFC registers for boot location NAND */
#define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
#define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
#define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3

#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR	0xffd00000	/* stack in RAM */
#define CONFIG_SYS_INIT_RAM_SIZE	0x00004000/* End of used area in RAM */

#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE \
						- GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
#define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc*/

/* Serial Port */
#define CONFIG_CONS_INDEX	1
#undef	CONFIG_SERIAL_SOFTWARE_FIFO
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE	1
#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
#ifdef CONFIG_SPL_BUILD
#define CONFIG_NS16550_MIN_FUNCTIONS
#endif

#define CONFIG_SYS_BAUDRATE_TABLE	\
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)

#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED	400000
#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000

/* I2C EEPROM */
#define CONFIG_CMD_EEPROM
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5

/* eSPI - Enhanced SPI */
#ifdef CONFIG_FSL_ESPI
#define CONFIG_SF_DEFAULT_SPEED		10000000
#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
#endif

#if defined(CONFIG_TSEC_ENET)

#define CONFIG_MII			/* MII PHY management */
#define CONFIG_MII_DEFAULT_TSEC	1	/* Allow unregistered phys */
#define CONFIG_TSEC1	1
#define CONFIG_TSEC1_NAME	"eTSEC1"
#define CONFIG_TSEC2	1
#define CONFIG_TSEC2_NAME	"eTSEC2"

#define TSEC1_PHY_ADDR		0
#define TSEC2_PHY_ADDR		3

#define TSEC1_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC2_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)

#define TSEC1_PHYIDX		0

#define TSEC2_PHYIDX		0

#define CONFIG_ETHPRIME		"eTSEC1"

#define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */

#endif	/* CONFIG_TSEC_ENET */

/*
 * Environment
 */
#if defined(CONFIG_RAMBOOT_SPIFLASH)
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SPI_BUS	0
#define CONFIG_ENV_SPI_CS	0
#define CONFIG_ENV_SPI_MAX_HZ	10000000
#define CONFIG_ENV_SPI_MODE	0
#define CONFIG_ENV_OFFSET	0x100000	/* 1MB */
#define CONFIG_ENV_SECT_SIZE	0x10000
#define CONFIG_ENV_SIZE		0x2000
#elif defined(CONFIG_NAND)
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_ENV_SIZE		CONFIG_SYS_NAND_BLOCK_SIZE
#define CONFIG_ENV_OFFSET	((768 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE)
#define CONFIG_ENV_RANGE	(3 * CONFIG_ENV_SIZE)
#elif defined(CONFIG_SYS_RAMBOOT)
#define CONFIG_ENV_IS_NOWHERE	/* Store ENV in memory only */
#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
#define CONFIG_ENV_SIZE		0x2000
#endif

#define CONFIG_LOADS_ECHO		/* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE		/* allow baudrate change */

/*
 * Command line configuration.
 */
#define CONFIG_CMD_ERRATA
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_REGINFO

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
#define CONFIG_CMDLINE_EDITING			/* Command-line editing */
#define CONFIG_AUTO_COMPLETE			/* add autocompletion support */
#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */

#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
						/* Print Buffer Size */
#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 64 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ	(64 << 20) /* Initial Memory map for Linux */
#define CONFIG_SYS_BOOTM_LEN	(64 << 20) /* Increase max gunzip size */

#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
#endif

/* Hash command with SHA acceleration supported in hardware */
#ifdef CONFIG_FSL_CAAM
#define CONFIG_CMD_HASH
#define CONFIG_SHA_HW_ACCEL
#endif

#define CONFIG_USB_EHCI

#ifdef CONFIG_USB_EHCI
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#define CONFIG_HAS_FSL_DR_USB
#endif

/*
 * Dynamic MTD Partition support with mtdparts
 */
#define CONFIG_MTD_DEVICE
#define CONFIG_MTD_PARTITIONS
#define CONFIG_CMD_MTDPARTS
#define MTDIDS_DEFAULT "nand0=ff800000.flash,"
#define MTDPARTS_DEFAULT "mtdparts=ff800000.flash:1m(uboot)," \
			"8m(kernel),512k(dtb),-(fs)"

/*
 * Environment Configuration
 */

#if defined(CONFIG_TSEC_ENET)
#define CONFIG_HAS_ETH0
#endif

#define CONFIG_HOSTNAME		BSC9131rdb
#define CONFIG_ROOTPATH		"/opt/nfsroot"
#define CONFIG_BOOTFILE		"uImage"
#define CONFIG_UBOOTPATH	"u-boot.bin" /* U-Boot image on TFTP server */

#define CONFIG_BAUDRATE		115200

#define	CONFIG_EXTRA_ENV_SETTINGS				\
	"netdev=eth0\0"						\
	"uboot=" CONFIG_UBOOTPATH "\0"				\
	"loadaddr=1000000\0"			\
	"bootfile=uImage\0"	\
	"consoledev=ttyS0\0"				\
	"ramdiskaddr=2000000\0"			\
	"ramdiskfile=rootfs.ext2.gz.uboot\0"		\
	"fdtaddr=1e00000\0"				\
	"fdtfile=bsc9131rdb.dtb\0"		\
	"bdev=sda1\0"	\
	"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0"	\
	"bootm_size=0x37000000\0"	\
	"othbootargs=ramdisk_size=600000 " \
	"default_hugepagesz=256m hugepagesz=256m hugepages=1\0" \
	"usbext2boot=setenv bootargs root=/dev/ram rw "	\
	"console=$consoledev,$baudrate $othbootargs; "	\
	"usb start;"			\
	"ext2load usb 0:4 $loadaddr $bootfile;"		\
	"ext2load usb 0:4 $fdtaddr $fdtfile;"	\
	"ext2load usb 0:4 $ramdiskaddr $ramdiskfile;"	\
	"bootm $loadaddr $ramdiskaddr $fdtaddr\0"	\

#define CONFIG_RAMBOOTCOMMAND		\
	"setenv bootargs root=/dev/ram rw "	\
	"console=$consoledev,$baudrate $othbootargs; "	\
	"tftp $ramdiskaddr $ramdiskfile;"	\
	"tftp $loadaddr $bootfile;"		\
	"tftp $fdtaddr $fdtfile;"		\
	"bootm $loadaddr $ramdiskaddr $fdtaddr"

#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND

#endif	/* __CONFIG_H */
Commit	Line	Data
	1	/*
	2	* Copyright 2011-2012 Freescale Semiconductor, Inc.
	3	*
	4	* SPDX-License-Identifier: GPL-2.0+
	5	*/
	6
	7	/*
	8	* BSC9131 RDB board configuration file
	9	*/
	10
	11	#ifndef __CONFIG_H
	12	#define __CONFIG_H
	13
	14	#define CONFIG_NAND_FSL_IFC
	15
	16	#ifdef CONFIG_SPIFLASH
	17	#define CONFIG_RAMBOOT_SPIFLASH
	18	#define CONFIG_SYS_RAMBOOT
	19	#define CONFIG_SYS_EXTRA_ENV_RELOC
	20	#define CONFIG_SYS_TEXT_BASE 0x11000000
	21	#define CONFIG_RESET_VECTOR_ADDRESS 0x110bfffc
	22	#endif
	23
	24	#ifdef CONFIG_NAND
	25	#define CONFIG_SPL_INIT_MINIMAL
	26	#define CONFIG_SPL_NAND_BOOT
	27	#define CONFIG_SPL_FLUSH_IMAGE
	28	#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
	29
	30	#define CONFIG_SYS_TEXT_BASE 0x00201000
	31	#define CONFIG_SPL_TEXT_BASE 0xFFFFE000
	32	#define CONFIG_SPL_MAX_SIZE 8192
	33	#define CONFIG_SPL_RELOC_TEXT_BASE 0x00100000
	34	#define CONFIG_SPL_RELOC_STACK 0x00100000
	35	#define CONFIG_SYS_NAND_U_BOOT_SIZE ((768 << 10) - 0x2000)
	36	#define CONFIG_SYS_NAND_U_BOOT_DST (0x00200000 - CONFIG_SPL_MAX_SIZE)
	37	#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000
	38	#define CONFIG_SYS_NAND_U_BOOT_OFFS 0
	39	#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
	40	#endif
	41
	42	#ifdef CONFIG_SPL_BUILD
	43	#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
	44	#else
	45	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
	46	#endif
	47
	48	/* High Level Configuration Options */
	49	#define CONFIG_FSL_CAAM /* Enable SEC/CAAM */
	50
	51	#define CONFIG_TSEC_ENET
	52	#define CONFIG_ENV_OVERWRITE
	53
	54	#define CONFIG_DDR_CLK_FREQ 66666666 /* DDRCLK on 9131 RDB */
	55	#if defined(CONFIG_SYS_CLK_100)
	56	#define CONFIG_SYS_CLK_FREQ 100000000 /* SYSCLK for 9131 RDB */
	57	#else
	58	#define CONFIG_SYS_CLK_FREQ 66666666 /* SYSCLK for 9131 RDB */
	59	#endif
	60
	61	#define CONFIG_HWCONFIG
	62	/*
	63	* These can be toggled for performance analysis, otherwise use default.
	64	*/
	65	#define CONFIG_L2_CACHE /* toggle L2 cache */
	66	#define CONFIG_BTB /* enable branch predition */
	67
	68	#define CONFIG_SYS_MEMTEST_START 0x01000000 /* memtest works on */
	69	#define CONFIG_SYS_MEMTEST_END 0x01ffffff
	70
	71	/* DDR Setup */
	72	#undef CONFIG_SYS_DDR_RAW_TIMING
	73	#undef CONFIG_DDR_SPD
	74	#define CONFIG_SYS_SPD_BUS_NUM 0
	75	#define SPD_EEPROM_ADDRESS 0x52 /* I2C access */
	76
	77	#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
	78
	79	#ifndef __ASSEMBLY__
	80	extern unsigned long get_sdram_size(void);
	81	#endif
	82	#define CONFIG_SYS_SDRAM_SIZE get_sdram_size() /* DDR size */
	83	#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
	84	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
	85
	86	#define CONFIG_DIMM_SLOTS_PER_CTLR 1
	87	#define CONFIG_CHIP_SELECTS_PER_CTRL 1
	88
	89	#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f
	90	#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302
	91	#define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000
	92
	93	#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
	94	#define CONFIG_SYS_DDR_INIT_ADDR 0x00000000
	95	#define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000
	96	#define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000
	97
	98	#define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600
	99	#define CONFIG_SYS_DDR_SR_CNTR 0x00000000
	100	#define CONFIG_SYS_DDR_RCW_1 0x00000000
	101	#define CONFIG_SYS_DDR_RCW_2 0x00000000
	102	#define CONFIG_SYS_DDR_CONTROL 0xC70C0000 /* Type = DDR3 */
	103	#define CONFIG_SYS_DDR_CONTROL_2 0x24401000
	104	#define CONFIG_SYS_DDR_TIMING_4 0x00000001
	105	#define CONFIG_SYS_DDR_TIMING_5 0x02401400
	106
	107	#define CONFIG_SYS_DDR_TIMING_3_800 0x00030000
	108	#define CONFIG_SYS_DDR_TIMING_0_800 0x00110104
	109	#define CONFIG_SYS_DDR_TIMING_1_800 0x6f6b8644
	110	#define CONFIG_SYS_DDR_TIMING_2_800 0x0fa888cf
	111	#define CONFIG_SYS_DDR_CLK_CTRL_800 0x03000000
	112	#define CONFIG_SYS_DDR_MODE_1_800 0x00441420
	113	#define CONFIG_SYS_DDR_MODE_2_800 0x8000c000
	114	#define CONFIG_SYS_DDR_INTERVAL_800 0x0c300100
	115	#define CONFIG_SYS_DDR_WRLVL_CONTROL_800 0x8675f608
	116
	117	/*
	118	* Base addresses -- Note these are effective addresses where the
	119	* actual resources get mapped (not physical addresses)
	120	*/
	121	/* relocated CCSRBAR */
	122	#define CONFIG_SYS_CCSRBAR CONFIG_SYS_CCSRBAR_DEFAULT
	123	#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR_DEFAULT
	124
	125	#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses */
	126	/* CONFIG_SYS_IMMR */
	127	/* DSP CCSRBAR */
	128	#define CONFIG_SYS_FSL_DSP_CCSRBAR CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
	129	#define CONFIG_SYS_FSL_DSP_CCSRBAR_PHYS CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
	130
	131	/*
	132	* Memory map
	133	*
	134	* 0x0000_0000 0x3FFF_FFFF DDR 1G cacheable
	135	* 0x8800_0000 0x8810_0000 IFC internal SRAM 1M
	136	* 0xB000_0000 0xB0FF_FFFF DSP core M2 memory 16M
	137	* 0xC100_0000 0xC13F_FFFF MAPLE-2F 4M
	138	* 0xC1F0_0000 0xC1F3_FFFF PA L2 SRAM Region 0 256K
	139	* 0xC1F8_0000 0xC1F9_FFFF PA L2 SRAM Region 1 128K
	140	* 0xFED0_0000 0xFED0_3FFF SEC Secured RAM 16K
	141	* 0xFF60_0000 0xFF6F_FFFF DSP CCSR 1M
	142	* 0xFF70_0000 0xFF7F_FFFF PA CCSR 1M
	143	* 0xFF80_0000 0xFFFF_FFFF Boot Page & NAND flash buffer 8M
	144	*
	145	*/
	146
	147	/*
	148	* IFC Definitions
	149	*/
	150
	151	/* NAND Flash on IFC */
	152	#define CONFIG_SYS_NAND_BASE 0xff800000
	153	#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
	154
	155	#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
	156	\| CSPR_PORT_SIZE_8 /* Port Size = 8 bit*/ \
	157	\| CSPR_MSEL_NAND /* MSEL = NAND */ \
	158	\| CSPR_V)
	159	#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
	160
	161	#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
	162	\| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
	163	\| CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
	164	\| CSOR_NAND_RAL_2 /* RAL = 2Byes */ \
	165	\| CSOR_NAND_PGS_2K /* Page Size = 2K */ \
	166	\| CSOR_NAND_SPRZ_64 /* Spare size = 64 */ \
	167	\| CSOR_NAND_PB(64)) /Pages Per Block = 64/
	168
	169	/* NAND Flash Timing Params */
	170	#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x03) \
	171	\| FTIM0_NAND_TWP(0x05) \
	172	\| FTIM0_NAND_TWCHT(0x02) \
	173	\| FTIM0_NAND_TWH(0x04))
	174	#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x1C) \
	175	\| FTIM1_NAND_TWBE(0x1E) \
	176	\| FTIM1_NAND_TRR(0x07) \
	177	\| FTIM1_NAND_TRP(0x05))
	178	#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x08) \
	179	\| FTIM2_NAND_TREH(0x04) \
	180	\| FTIM2_NAND_TWHRE(0x11))
	181	#define CONFIG_SYS_NAND_FTIM3 FTIM3_NAND_TWW(0x04)
	182
	183	#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
	184	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	185	#define CONFIG_CMD_NAND
	186	#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
	187
	188	#define CONFIG_SYS_NAND_DDR_LAW 11
	189
	190	/* Set up IFC registers for boot location NAND */
	191	#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
	192	#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
	193	#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
	194	#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
	195	#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
	196	#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
	197	#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
	198
	199	#define CONFIG_SYS_INIT_RAM_LOCK
	200	#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */
	201	#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000/* End of used area in RAM */
	202
	203	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \
	204	- GENERATED_GBL_DATA_SIZE)
	205	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
	206
	207	#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
	208	#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc*/
	209
	210	/* Serial Port */
	211	#define CONFIG_CONS_INDEX 1
	212	#undef CONFIG_SERIAL_SOFTWARE_FIFO
	213	#define CONFIG_SYS_NS16550_SERIAL
	214	#define CONFIG_SYS_NS16550_REG_SIZE 1
	215	#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
	216	#ifdef CONFIG_SPL_BUILD
	217	#define CONFIG_NS16550_MIN_FUNCTIONS
	218	#endif
	219
	220	#define CONFIG_SYS_BAUDRATE_TABLE \
	221	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
	222
	223	#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
	224
	225	#define CONFIG_SYS_I2C
	226	#define CONFIG_SYS_I2C_FSL
	227	#define CONFIG_SYS_FSL_I2C_SPEED 400000
	228	#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
	229	#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
	230
	231	/* I2C EEPROM */
	232	#define CONFIG_CMD_EEPROM
	233	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
	234	#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
	235	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
	236
	237	/* eSPI - Enhanced SPI */
	238	#ifdef CONFIG_FSL_ESPI
	239	#define CONFIG_SF_DEFAULT_SPEED 10000000
	240	#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
	241	#endif
	242
	243	#if defined(CONFIG_TSEC_ENET)
	244
	245	#define CONFIG_MII /* MII PHY management */
	246	#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
	247	#define CONFIG_TSEC1 1
	248	#define CONFIG_TSEC1_NAME "eTSEC1"
	249	#define CONFIG_TSEC2 1
	250	#define CONFIG_TSEC2_NAME "eTSEC2"
	251
	252	#define TSEC1_PHY_ADDR 0
	253	#define TSEC2_PHY_ADDR 3
	254
	255	#define TSEC1_FLAGS (TSEC_GIGABIT \| TSEC_REDUCED)
	256	#define TSEC2_FLAGS (TSEC_GIGABIT \| TSEC_REDUCED)
	257
	258	#define TSEC1_PHYIDX 0
	259
	260	#define TSEC2_PHYIDX 0
	261
	262	#define CONFIG_ETHPRIME "eTSEC1"
	263
	264	#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
	265
	266	#endif /* CONFIG_TSEC_ENET */
	267
	268	/*
	269	* Environment
	270	*/
	271	#if defined(CONFIG_RAMBOOT_SPIFLASH)
	272	#define CONFIG_ENV_IS_IN_SPI_FLASH
	273	#define CONFIG_ENV_SPI_BUS 0
	274	#define CONFIG_ENV_SPI_CS 0
	275	#define CONFIG_ENV_SPI_MAX_HZ 10000000
	276	#define CONFIG_ENV_SPI_MODE 0
	277	#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
	278	#define CONFIG_ENV_SECT_SIZE 0x10000
	279	#define CONFIG_ENV_SIZE 0x2000
	280	#elif defined(CONFIG_NAND)
	281	#define CONFIG_ENV_IS_IN_NAND
	282	#define CONFIG_SYS_EXTRA_ENV_RELOC
	283	#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
	284	#define CONFIG_ENV_OFFSET ((768 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE)
	285	#define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE)
	286	#elif defined(CONFIG_SYS_RAMBOOT)
	287	#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */
	288	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
	289	#define CONFIG_ENV_SIZE 0x2000
	290	#endif
	291
	292	#define CONFIG_LOADS_ECHO /* echo on for serial download */
	293	#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
	294
	295	/*
	296	* Command line configuration.
	297	*/
	298	#define CONFIG_CMD_ERRATA
	299	#define CONFIG_CMD_IRQ
	300	#define CONFIG_CMD_REGINFO
	301
	302	/*
	303	* Miscellaneous configurable options
	304	*/
	305	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	306	#define CONFIG_CMDLINE_EDITING /* Command-line editing */
	307	#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
	308	#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
	309
	310	#if defined(CONFIG_CMD_KGDB)
	311	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	312	#else
	313	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	314	#endif
	315	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
	316	/* Print Buffer Size */
	317	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	318	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
	319
	320	/*
	321	* For booting Linux, the board info and command line data
	322	* have to be in the first 64 MB of memory, since this is
	323	* the maximum mapped by the Linux kernel during initialization.
	324	*/
	325	#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux */
	326	#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
	327
	328	#if defined(CONFIG_CMD_KGDB)
	329	#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
	330	#endif
	331
	332	/* Hash command with SHA acceleration supported in hardware */
	333	#ifdef CONFIG_FSL_CAAM
	334	#define CONFIG_CMD_HASH
	335	#define CONFIG_SHA_HW_ACCEL
	336	#endif
	337
	338	#define CONFIG_USB_EHCI
	339
	340	#ifdef CONFIG_USB_EHCI
	341	#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
	342	#define CONFIG_USB_EHCI_FSL
	343	#define CONFIG_HAS_FSL_DR_USB
	344	#endif
	345
	346	/*
	347	* Dynamic MTD Partition support with mtdparts
	348	*/
	349	#define CONFIG_MTD_DEVICE
	350	#define CONFIG_MTD_PARTITIONS
	351	#define CONFIG_CMD_MTDPARTS
	352	#define MTDIDS_DEFAULT "nand0=ff800000.flash,"
	353	#define MTDPARTS_DEFAULT "mtdparts=ff800000.flash:1m(uboot)," \
	354	"8m(kernel),512k(dtb),-(fs)"
	355
	356	/*
	357	* Environment Configuration
	358	*/
	359
	360	#if defined(CONFIG_TSEC_ENET)
	361	#define CONFIG_HAS_ETH0
	362	#endif
	363
	364	#define CONFIG_HOSTNAME BSC9131rdb
	365	#define CONFIG_ROOTPATH "/opt/nfsroot"
	366	#define CONFIG_BOOTFILE "uImage"
	367	#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */
	368
	369	#define CONFIG_BAUDRATE 115200
	370
	371	#define CONFIG_EXTRA_ENV_SETTINGS \
	372	"netdev=eth0\0" \
	373	"uboot=" CONFIG_UBOOTPATH "\0" \
	374	"loadaddr=1000000\0" \
	375	"bootfile=uImage\0" \
	376	"consoledev=ttyS0\0" \
	377	"ramdiskaddr=2000000\0" \
	378	"ramdiskfile=rootfs.ext2.gz.uboot\0" \
	379	"fdtaddr=1e00000\0" \
	380	"fdtfile=bsc9131rdb.dtb\0" \
	381	"bdev=sda1\0" \
	382	"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0" \
	383	"bootm_size=0x37000000\0" \
	384	"othbootargs=ramdisk_size=600000 " \
	385	"default_hugepagesz=256m hugepagesz=256m hugepages=1\0" \
	386	"usbext2boot=setenv bootargs root=/dev/ram rw " \
	387	"console=$consoledev,$baudrate $othbootargs; " \
	388	"usb start;" \
	389	"ext2load usb 0:4 $loadaddr $bootfile;" \
	390	"ext2load usb 0:4 $fdtaddr $fdtfile;" \
	391	"ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \
	392	"bootm $loadaddr $ramdiskaddr $fdtaddr\0" \
	393
	394	#define CONFIG_RAMBOOTCOMMAND \
	395	"setenv bootargs root=/dev/ram rw " \
	396	"console=$consoledev,$baudrate $othbootargs; " \
	397	"tftp $ramdiskaddr $ramdiskfile;" \
	398	"tftp $loadaddr $bootfile;" \
	399	"tftp $fdtaddr $fdtfile;" \
	400	"bootm $loadaddr $ramdiskaddr $fdtaddr"
	401
	402	#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
	403
	404	#endif /* __CONFIG_H */