common/cmd_eeprom.c

   1 /*
   2  * (C) Copyright 2000, 2001
   3  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 /*
   9  * Support for read and write access to EEPROM like memory devices. This
  10  * includes regular EEPROM as well as  FRAM (ferroelectic nonvolaile RAM).
  11  * FRAM devices read and write data at bus speed. In particular, there is no
  12  * write delay. Also, there is no limit imposed on the number of bytes that can
  13  * be transferred with a single read or write.
  14  *
  15  * Use the following configuration options to ensure no unneeded performance
  16  * degradation (typical for EEPROM) is incured for FRAM memory:
  17  *
  18  * #define CONFIG_SYS_I2C_FRAM
  19  * #undef CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS
  20  *
  21  */
  22
  23 #include <common.h>
  24 #include <config.h>
  25 #include <command.h>
  26 #include <i2c.h>
  27
  28 extern void eeprom_init  (void);
  29 extern int  eeprom_read  (unsigned dev_addr, unsigned offset,
  30                           uchar *buffer, unsigned cnt);
  31 extern int  eeprom_write (unsigned dev_addr, unsigned offset,
  32                           uchar *buffer, unsigned cnt);
  33 #if defined(CONFIG_SYS_EEPROM_WREN)
  34 extern int eeprom_write_enable (unsigned dev_addr, int state);
  35 #endif
  36
  37
  38 #if defined(CONFIG_SYS_EEPROM_X40430)
  39         /* Maximum number of times to poll for acknowledge after write */
  40 #define MAX_ACKNOWLEDGE_POLLS   10
  41 #endif
  42
  43 /* ------------------------------------------------------------------------- */
  44
  45 #if defined(CONFIG_CMD_EEPROM)
  46 static int do_eeprom(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
  47 {
  48         const char *const fmt =
  49                 "\nEEPROM @0x%lX %s: addr %08lx  off %04lx  count %ld ... ";
  50
  51 #if defined(CONFIG_SYS_I2C_MULTI_EEPROMS)
  52         if (argc == 6) {
  53                 ulong dev_addr = simple_strtoul (argv[2], NULL, 16);
  54                 ulong addr = simple_strtoul (argv[3], NULL, 16);
  55                 ulong off  = simple_strtoul (argv[4], NULL, 16);
  56                 ulong cnt  = simple_strtoul (argv[5], NULL, 16);
  57 #else
  58         if (argc == 5) {
  59                 ulong dev_addr = CONFIG_SYS_DEF_EEPROM_ADDR;
  60                 ulong addr = simple_strtoul (argv[2], NULL, 16);
  61                 ulong off  = simple_strtoul (argv[3], NULL, 16);
  62                 ulong cnt  = simple_strtoul (argv[4], NULL, 16);
  63 #endif /* CONFIG_SYS_I2C_MULTI_EEPROMS */
  64
  65 # if !defined(CONFIG_SPI) || defined(CONFIG_ENV_EEPROM_IS_ON_I2C)
  66                 eeprom_init ();
  67 # endif /* !CONFIG_SPI */
  68
  69                 if (strcmp (argv[1], "read") == 0) {
  70                         int rcode;
  71
  72                         printf (fmt, dev_addr, argv[1], addr, off, cnt);
  73
  74                         rcode = eeprom_read (dev_addr, off, (uchar *) addr, cnt);
  75
  76                         puts ("done\n");
  77                         return rcode;
  78                 } else if (strcmp (argv[1], "write") == 0) {
  79                         int rcode;
  80
  81                         printf (fmt, dev_addr, argv[1], addr, off, cnt);
  82
  83                         rcode = eeprom_write (dev_addr, off, (uchar *) addr, cnt);
  84
  85                         puts ("done\n");
  86                         return rcode;
  87                 }
  88         }
  89
  90         return CMD_RET_USAGE;
  91 }
  92 #endif
  93
  94 /*-----------------------------------------------------------------------
  95  *
  96  * for CONFIG_SYS_I2C_EEPROM_ADDR_LEN == 2 (16-bit EEPROM address) offset is
  97  *   0x000nxxxx for EEPROM address selectors at n, offset xxxx in EEPROM.
  98  *
  99  * for CONFIG_SYS_I2C_EEPROM_ADDR_LEN == 1 (8-bit EEPROM page address) offset is
 100  *   0x00000nxx for EEPROM address selectors and page number at n.
 101  */
 102
 103 #if !defined(CONFIG_SPI) || defined(CONFIG_ENV_EEPROM_IS_ON_I2C)
 104 #if !defined(CONFIG_SYS_I2C_EEPROM_ADDR_LEN) || CONFIG_SYS_I2C_EEPROM_ADDR_LEN < 1 || CONFIG_SYS_I2C_EEPROM_ADDR_LEN > 2
 105 #error CONFIG_SYS_I2C_EEPROM_ADDR_LEN must be 1 or 2
 106 #endif
 107 #endif
 108
 109 int eeprom_read (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt)
 110 {
 111         unsigned end = offset + cnt;
 112         unsigned blk_off;
 113         int rcode = 0;
 114
 115         /* Read data until done or would cross a page boundary.
 116          * We must write the address again when changing pages
 117          * because the next page may be in a different device.
 118          */
 119         while (offset < end) {
 120                 unsigned alen, len;
 121 #if !defined(CONFIG_SYS_I2C_FRAM)
 122                 unsigned maxlen;
 123 #endif
 124
 125 #if CONFIG_SYS_I2C_EEPROM_ADDR_LEN == 1 && !defined(CONFIG_SPI_X)
 126                 uchar addr[2];
 127
 128                 blk_off = offset & 0xFF;        /* block offset */
 129
 130                 addr[0] = offset >> 8;          /* block number */
 131                 addr[1] = blk_off;              /* block offset */
 132                 alen    = 2;
 133 #else
 134                 uchar addr[3];
 135
 136                 blk_off = offset & 0xFF;        /* block offset */
 137
 138                 addr[0] = offset >> 16;         /* block number */
 139                 addr[1] = offset >>  8;         /* upper address octet */
 140                 addr[2] = blk_off;              /* lower address octet */
 141                 alen    = 3;
 142 #endif  /* CONFIG_SYS_I2C_EEPROM_ADDR_LEN, CONFIG_SPI_X */
 143
 144                 addr[0] |= dev_addr;            /* insert device address */
 145
 146                 len = end - offset;
 147
 148                 /*
 149                  * For a FRAM device there is no limit on the number of the
 150                  * bytes that can be ccessed with the single read or write
 151                  * operation.
 152                  */
 153 #if !defined(CONFIG_SYS_I2C_FRAM)
 154                 maxlen = 0x100 - blk_off;
 155                 if (maxlen > I2C_RXTX_LEN)
 156                         maxlen = I2C_RXTX_LEN;
 157                 if (len > maxlen)
 158                         len = maxlen;
 159 #endif
 160
 161 #if defined(CONFIG_SPI) && !defined(CONFIG_ENV_EEPROM_IS_ON_I2C)
 162                 spi_read (addr, alen, buffer, len);
 163 #else
 164 #if defined(CONFIG_SYS_I2C_EEPROM_BUS)
 165                 i2c_set_bus_num(CONFIG_SYS_I2C_EEPROM_BUS);
 166 #endif
 167                 if (i2c_read(addr[0], offset, alen - 1, buffer, len))
 168                         rcode = 1;
 169 #endif
 170                 buffer += len;
 171                 offset += len;
 172         }
 173
 174         return rcode;
 175 }
 176
 177 /*-----------------------------------------------------------------------
 178  *
 179  * for CONFIG_SYS_I2C_EEPROM_ADDR_LEN == 2 (16-bit EEPROM address) offset is
 180  *   0x000nxxxx for EEPROM address selectors at n, offset xxxx in EEPROM.
 181  *
 182  * for CONFIG_SYS_I2C_EEPROM_ADDR_LEN == 1 (8-bit EEPROM page address) offset is
 183  *   0x00000nxx for EEPROM address selectors and page number at n.
 184  */
 185
 186 int eeprom_write (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt)
 187 {
 188         unsigned end = offset + cnt;
 189         unsigned blk_off;
 190         int rcode = 0;
 191
 192 #if defined(CONFIG_SYS_EEPROM_X40430)
 193         uchar   contr_r_addr[2];
 194         uchar   addr_void[2];
 195         uchar   contr_reg[2];
 196         uchar   ctrl_reg_v;
 197         int     i;
 198 #endif
 199
 200 #if defined(CONFIG_SYS_EEPROM_WREN)
 201         eeprom_write_enable (dev_addr,1);
 202 #endif
 203         /* Write data until done or would cross a write page boundary.
 204          * We must write the address again when changing pages
 205          * because the address counter only increments within a page.
 206          */
 207
 208         while (offset < end) {
 209                 unsigned alen, len;
 210 #if !defined(CONFIG_SYS_I2C_FRAM)
 211                 unsigned maxlen;
 212 #endif
 213
 214 #if CONFIG_SYS_I2C_EEPROM_ADDR_LEN == 1 && !defined(CONFIG_SPI_X)
 215                 uchar addr[2];
 216
 217                 blk_off = offset & 0xFF;        /* block offset */
 218
 219                 addr[0] = offset >> 8;          /* block number */
 220                 addr[1] = blk_off;              /* block offset */
 221                 alen    = 2;
 222 #else
 223                 uchar addr[3];
 224
 225                 blk_off = offset & 0xFF;        /* block offset */
 226
 227                 addr[0] = offset >> 16;         /* block number */
 228                 addr[1] = offset >>  8;         /* upper address octet */
 229                 addr[2] = blk_off;              /* lower address octet */
 230                 alen    = 3;
 231 #endif  /* CONFIG_SYS_I2C_EEPROM_ADDR_LEN, CONFIG_SPI_X */
 232
 233                 addr[0] |= dev_addr;            /* insert device address */
 234
 235                 len = end - offset;
 236
 237                 /*
 238                  * For a FRAM device there is no limit on the number of the
 239                  * bytes that can be accessed with the single read or write
 240                  * operation.
 241                  */
 242 #if !defined(CONFIG_SYS_I2C_FRAM)
 243
 244 #if defined(CONFIG_SYS_EEPROM_PAGE_WRITE_BITS)
 245
 246 #define EEPROM_PAGE_SIZE        (1 << CONFIG_SYS_EEPROM_PAGE_WRITE_BITS)
 247 #define EEPROM_PAGE_OFFSET(x)   ((x) & (EEPROM_PAGE_SIZE - 1))
 248
 249                 maxlen = EEPROM_PAGE_SIZE - EEPROM_PAGE_OFFSET(blk_off);
 250 #else
 251                 maxlen = 0x100 - blk_off;
 252 #endif
 253                 if (maxlen > I2C_RXTX_LEN)
 254                         maxlen = I2C_RXTX_LEN;
 255
 256                 if (len > maxlen)
 257                         len = maxlen;
 258 #endif
 259
 260 #if defined(CONFIG_SPI) && !defined(CONFIG_ENV_EEPROM_IS_ON_I2C)
 261                 spi_write (addr, alen, buffer, len);
 262 #else
 263 #if defined(CONFIG_SYS_EEPROM_X40430)
 264                 /* Get the value of the control register.
 265                  * Set current address (internal pointer in the x40430)
 266                  * to 0x1ff.
 267                  */
 268                 contr_r_addr[0] = 9;
 269                 contr_r_addr[1] = 0xff;
 270                 addr_void[0]    = 0;
 271                 addr_void[1]    = addr[1];
 272 #ifdef CONFIG_SYS_I2C_EEPROM_ADDR
 273                 contr_r_addr[0] |= CONFIG_SYS_I2C_EEPROM_ADDR;
 274                 addr_void[0]    |= CONFIG_SYS_I2C_EEPROM_ADDR;
 275 #endif
 276                 contr_reg[0] = 0xff;
 277                 if (i2c_read (contr_r_addr[0], contr_r_addr[1], 1, contr_reg, 1) != 0) {
 278                         rcode = 1;
 279                 }
 280                 ctrl_reg_v = contr_reg[0];
 281
 282                 /* Are any of the eeprom blocks write protected?
 283                  */
 284                 if (ctrl_reg_v & 0x18) {
 285                         ctrl_reg_v &= ~0x18;   /* reset block protect bits  */
 286                         ctrl_reg_v |=  0x02;   /* set write enable latch    */
 287                         ctrl_reg_v &= ~0x04;   /* clear RWEL                */
 288
 289                         /* Set write enable latch.
 290                          */
 291                         contr_reg[0] = 0x02;
 292                         if (i2c_write (contr_r_addr[0], 0xff, 1, contr_reg, 1) != 0) {
 293                                 rcode = 1;
 294                         }
 295
 296                         /* Set register write enable latch.
 297                          */
 298                         contr_reg[0] = 0x06;
 299                         if (i2c_write (contr_r_addr[0], 0xFF, 1, contr_reg, 1) != 0) {
 300                                 rcode = 1;
 301                         }
 302
 303                         /* Modify ctrl register.
 304                          */
 305                         contr_reg[0] = ctrl_reg_v;
 306                         if (i2c_write (contr_r_addr[0], 0xFF, 1, contr_reg, 1) != 0) {
 307                                 rcode = 1;
 308                         }
 309
 310                         /* The write (above) is an operation on NV memory.
 311                          * These can take some time (~5ms), and the device
 312                          * will not respond to further I2C messages till
 313                          * it's completed the write.
 314                          * So poll device for an I2C acknowledge.
 315                          * When we get one we know we can continue with other
 316                          * operations.
 317                          */
 318                         contr_reg[0] = 0;
 319                         for (i = 0; i < MAX_ACKNOWLEDGE_POLLS; i++) {
 320                                 if (i2c_read (addr_void[0], addr_void[1], 1, contr_reg, 1) == 0)
 321                                         break;  /* got ack */
 322 #if defined(CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS)
 323                                 udelay(CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS * 1000);
 324 #endif
 325                         }
 326                         if (i == MAX_ACKNOWLEDGE_POLLS) {
 327                                 puts ("EEPROM poll acknowledge failed\n");
 328                                 rcode = 1;
 329                         }
 330                 }
 331
 332                 /* Is the write enable latch on?.
 333                  */
 334                 else if (!(ctrl_reg_v & 0x02)) {
 335                         /* Set write enable latch.
 336                          */
 337                         contr_reg[0] = 0x02;
 338                         if (i2c_write (contr_r_addr[0], 0xFF, 1, contr_reg, 1) != 0) {
 339                                rcode = 1;
 340                         }
 341                 }
 342                 /* Write is enabled ... now write eeprom value.
 343                  */
 344 #endif
 345 #if defined(CONFIG_SYS_I2C_EEPROM_BUS)
 346                 i2c_set_bus_num(CONFIG_SYS_I2C_EEPROM_BUS);
 347 #endif
 348                 if (i2c_write(addr[0], offset, alen - 1, buffer, len))
 349                         rcode = 1;
 350
 351 #endif
 352                 buffer += len;
 353                 offset += len;
 354
 355 #if defined(CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS)
 356                 udelay(CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS * 1000);
 357 #endif
 358         }
 359 #if defined(CONFIG_SYS_EEPROM_WREN)
 360         eeprom_write_enable (dev_addr,0);
 361 #endif
 362         return rcode;
 363 }
 364
 365 #if !defined(CONFIG_SPI) || defined(CONFIG_ENV_EEPROM_IS_ON_I2C)
 366 int
 367 eeprom_probe (unsigned dev_addr, unsigned offset)
 368 {
 369         unsigned char chip;
 370
 371         /* Probe the chip address
 372          */
 373 #if CONFIG_SYS_I2C_EEPROM_ADDR_LEN == 1 && !defined(CONFIG_SPI_X)
 374         chip = offset >> 8;             /* block number */
 375 #else
 376         chip = offset >> 16;            /* block number */
 377 #endif  /* CONFIG_SYS_I2C_EEPROM_ADDR_LEN, CONFIG_SPI_X */
 378
 379         chip |= dev_addr;               /* insert device address */
 380
 381         return (i2c_probe (chip));
 382 }
 383 #endif
 384
 385 /*-----------------------------------------------------------------------
 386  * Set default values
 387  */
 388 #ifndef CONFIG_SYS_I2C_SPEED
 389 #define CONFIG_SYS_I2C_SPEED    50000
 390 #endif
 391
 392 void eeprom_init  (void)
 393 {
 394
 395 #if defined(CONFIG_SPI) && !defined(CONFIG_ENV_EEPROM_IS_ON_I2C)
 396         spi_init_f ();
 397 #endif
 398 #if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT)
 399         i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
 400 #endif
 401 }
 402
 403 /*-----------------------------------------------------------------------
 404  */
 405
 406 /***************************************************/
 407
 408 #if defined(CONFIG_CMD_EEPROM)
 409
 410 #ifdef CONFIG_SYS_I2C_MULTI_EEPROMS
 411 U_BOOT_CMD(
 412         eeprom, 6,      1,      do_eeprom,
 413         "EEPROM sub-system",
 414         "read  devaddr addr off cnt\n"
 415         "eeprom write devaddr addr off cnt\n"
 416         "       - read/write `cnt' bytes from `devaddr` EEPROM at offset `off'"
 417 )
 418 #else /* One EEPROM */
 419 U_BOOT_CMD(
 420         eeprom, 5,      1,      do_eeprom,
 421         "EEPROM sub-system",
 422         "read  addr off cnt\n"
 423         "eeprom write addr off cnt\n"
 424         "       - read/write `cnt' bytes at EEPROM offset `off'"
 425 )
 426 #endif /* CONFIG_SYS_I2C_MULTI_EEPROMS */
 427
 428 #endif