drivers/usb/Kconfig

   1 menuconfig USB
   2         bool "USB support"
   3         ---help---
   4           Universal Serial Bus (USB) is a specification for a serial bus
   5           subsystem which offers higher speeds and more features than the
   6           traditional PC serial port.  The bus supplies power to peripherals
   7           and allows for hot swapping.  Up to 127 USB peripherals can be
   8           connected to a single USB host in a tree structure.
   9
  10           The USB host is the root of the tree, the peripherals are the
  11           leaves and the inner nodes are special USB devices called hubs.
  12           Most PCs now have USB host ports, used to connect peripherals
  13           such as scanners, keyboards, mice, modems, cameras, disks,
  14           flash memory, network links, and printers to the PC.
  15
  16           Say Y here if your device has an USB port, either host, peripheral or
  17           dual-role.
  18
  19           For an USB host port, you then need to say Y to at least one of the
  20           Host Controller Driver (HCD) options below.  Choose a USB 1.1
  21           controller, such as "UHCI HCD support" or "OHCI HCD support",
  22           and "EHCI HCD (USB 2.0) support" except for older systems that
  23           do not have USB 2.0 support.  It doesn't normally hurt to select
  24           them all if you are not certain.
  25
  26           If your system has a device-side USB port, used in the peripheral
  27           side of the USB protocol, see the "USB Gadget" framework instead.
  28
  29           After choosing your HCD, then select drivers for the USB peripherals
  30           you'll be using.  You may want to check out the information provided
  31           in <file:Documentation/usb/> and especially the links given in
  32           <file:Documentation/usb/usb-help.txt>.
  33
  34 if USB
  35
  36 config DM_USB
  37         bool "Enable driver model for USB"
  38         depends on USB && DM
  39         help
  40           Enable driver model for USB. The USB interface is then implemented
  41           by the USB uclass. Multiple USB controllers of different types
  42           (XHCI, EHCI) can be attached and used. The 'usb' command works as
  43           normal. OCHI is not supported at present.
  44
  45           Much of the code is shared but with this option enabled the USB
  46           uclass takes care of device enumeration. USB devices can be
  47           declared with the U_BOOT_USB_DEVICE() macro and will be
  48           automatically probed when found on the bus.
  49
  50 source "drivers/usb/host/Kconfig"
  51
  52 source "drivers/usb/dwc3/Kconfig"
  53
  54 source "drivers/usb/musb/Kconfig"
  55
  56 source "drivers/usb/musb-new/Kconfig"
  57
  58 source "drivers/usb/emul/Kconfig"
  59
  60 source "drivers/usb/phy/Kconfig"
  61
  62 source "drivers/usb/ulpi/Kconfig"
  63
  64 comment "USB peripherals"
  65
  66 config USB_STORAGE
  67         bool "USB Mass Storage support"
  68         ---help---
  69           Say Y here if you want to connect USB mass storage devices to your
  70           board's USB port.
  71
  72 config USB_KEYBOARD
  73         bool "USB Keyboard support"
  74         ---help---
  75           Say Y here if you want to use a USB keyboard for U-Boot command line
  76           input.
  77
  78 if USB_KEYBOARD
  79
  80 choice
  81         prompt "USB keyboard polling"
  82         default SYS_USB_EVENT_POLL
  83         ---help---
  84           Enable a polling mechanism for USB keyboard.
  85
  86         config SYS_USB_EVENT_POLL
  87                 bool "Interrupt polling"
  88
  89         config SYS_USB_EVENT_POLL_VIA_INT_QUEUE
  90                 bool "Poll via interrupt queue"
  91
  92         config SYS_USB_EVENT_POLL_VIA_CONTROL_EP
  93                 bool "Poll via control EP"
  94
  95 endchoice
  96
  97 endif
  98
  99 source "drivers/usb/gadget/Kconfig"
 100
 101 source "drivers/usb/eth/Kconfig"
 102
 103 endif