include/configs/cobra5272.h

   1 /*
   2  * Configuation settings for the Sentec Cobra Board.
   3  *
   4  * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 /* ---
  10  * Version: U-Boot 1.0.0 - initial release for Sentec COBRA5272 board
  11  * Date: 2004-03-29
  12  * Author: Florian Schlote
  13  *
  14  * For a description of configuration options please refer also to the
  15  * general u-boot-1.x.x/README file
  16  * ---
  17  */
  18
  19 /* ---
  20  * board/config.h - configuration options, board specific
  21  * ---
  22  */
  23
  24 #ifndef _CONFIG_COBRA5272_H
  25 #define _CONFIG_COBRA5272_H
  26
  27 /* ---
  28  * Defines processor clock - important for correct timings concerning serial
  29  * interface etc.
  30  * ---
  31  */
  32
  33 #define CONFIG_SYS_CLK                  66000000
  34 #define CONFIG_SYS_SDRAM_SIZE           16              /* SDRAM size in MB */
  35
  36 /* ---
  37  * Enable use of Ethernet
  38  * ---
  39  */
  40 #define CONFIG_MCFFEC
  41
  42 /* Enable Dma Timer */
  43 #define CONFIG_MCFTMR
  44
  45 /* ---
  46  * Define baudrate for UART1 (console output, tftp, ...)
  47  * default value of CONFIG_BAUDRATE for Sentec board: 19200 baud
  48  * CONFIG_SYS_BAUDRATE_TABLE defines values that can be selected in u-boot command
  49  * interface
  50  * ---
  51  */
  52
  53 #define CONFIG_MCFUART
  54 #define CONFIG_SYS_UART_PORT            (0)
  55
  56 /* ---
  57  * set "#if 0" to "#if 1" if (Hardware)-WATCHDOG should be enabled & change
  58  * timeout acc. to your needs
  59  * #define CONFIG_WATCHDOG_TIMEOUT x , x is timeout in milliseconds, e. g. 10000
  60  * for 10 sec
  61  * ---
  62  */
  63
  64 #if 0
  65 #define CONFIG_WATCHDOG
  66 #define CONFIG_WATCHDOG_TIMEOUT 10000   /* timeout in milliseconds */
  67 #endif
  68
  69 /* ---
  70  * CONFIG_MONITOR_IS_IN_RAM defines if u-boot is started from a different
  71  * bootloader residing in flash ('chainloading'); if you want to use
  72  * chainloading or want to compile a u-boot binary that can be loaded into
  73  * RAM via BDM set
  74  *      "#if 0" to "#if 1"
  75  * You will need a first stage bootloader then, e. g. colilo or a working BDM
  76  * cable (Background Debug Mode)
  77  *
  78  * Setting #if 0: u-boot will start from flash and relocate itself to RAM
  79  *
  80  * Please do not forget to modify the setting of CONFIG_SYS_TEXT_BASE
  81  * in board/cobra5272/config.mk accordingly (#if 0: 0xffe00000; #if 1: 0x20000)
  82  *
  83  * ---
  84  */
  85
  86 #if 0
  87 #define CONFIG_MONITOR_IS_IN_RAM /* monitor is started from a preloader */
  88 #endif
  89
  90 /* ---
  91  * Configuration for environment
  92  * Environment is embedded in u-boot in the second sector of the flash
  93  * ---
  94  */
  95
  96 #ifndef CONFIG_MONITOR_IS_IN_RAM
  97 #define CONFIG_ENV_OFFSET               0x4000
  98 #define CONFIG_ENV_SECT_SIZE    0x2000
  99 #else
 100 #define CONFIG_ENV_ADDR         0xffe04000
 101 #define CONFIG_ENV_SECT_SIZE    0x2000
 102 #endif
 103
 104 #define LDS_BOARD_TEXT \
 105         . = DEFINED(env_offset) ? env_offset : .; \
 106         env/embedded.o(.text);
 107
 108 /*
 109  * BOOTP options
 110  */
 111 #define CONFIG_BOOTP_BOOTFILESIZE
 112
 113 /*
 114  * Command line configuration.
 115  */
 116
 117 #ifdef CONFIG_MCFFEC
 118 #       define CONFIG_MII               1
 119 #       define CONFIG_MII_INIT          1
 120 #       define CONFIG_SYS_DISCOVER_PHY
 121 #       define CONFIG_SYS_RX_ETH_BUFFER 8
 122 #       define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
 123
 124 #       define CONFIG_SYS_FEC0_PINMUX           0
 125 #       define CONFIG_SYS_FEC0_MIIBASE          CONFIG_SYS_FEC0_IOBASE
 126 #       define MCFFEC_TOUT_LOOP         50000
 127 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
 128 #       ifndef CONFIG_SYS_DISCOVER_PHY
 129 #               define FECDUPLEX        FULL
 130 #               define FECSPEED         _100BASET
 131 #       else
 132 #               ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
 133 #                       define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
 134 #               endif
 135 #       endif                   /* CONFIG_SYS_DISCOVER_PHY */
 136 #endif
 137
 138 /*
 139  *-----------------------------------------------------------------------------
 140  * Define user parameters that have to be customized most likely
 141  *-----------------------------------------------------------------------------
 142  */
 143
 144 /*AUTOBOOT settings - booting images automatically by u-boot after power on*/
 145
 146 /* The following settings will be contained in the environment block ; if you
 147 want to use a neutral environment all those settings can be manually set in
 148 u-boot: 'set' command */
 149
 150 #if 0
 151
 152 #define CONFIG_BOOTCOMMAND      "bootm 0xffe80000"      /*Autoboto command, please
 153 enter a valid image address in flash */
 154
 155 /* User network settings */
 156
 157 #define CONFIG_IPADDR 192.168.100.2             /* default board IP address */
 158 #define CONFIG_SERVERIP 192.168.100.1   /* default tftp server IP address */
 159
 160 #endif
 161
 162 #define CONFIG_SYS_LOAD_ADDR            0x20000         /*Defines default RAM address
 163 from which user programs will be started */
 164
 165 /*---*/
 166
 167 /*
 168  *-----------------------------------------------------------------------------
 169  * End of user parameters to be customized
 170  *-----------------------------------------------------------------------------
 171  */
 172
 173 /* ---
 174  * Defines memory range for test
 175  * ---
 176  */
 177
 178 #define CONFIG_SYS_MEMTEST_START        0x400
 179 #define CONFIG_SYS_MEMTEST_END          0x380000
 180
 181 /* ---
 182  * Low Level Configuration Settings
 183  * (address mappings, register initial values, etc.)
 184  * You should know what you are doing if you make changes here.
 185  * ---
 186  */
 187
 188 /* ---
 189  * Base register address
 190  * ---
 191  */
 192
 193 #define CONFIG_SYS_MBAR         0x10000000      /* Register Base Addrs */
 194
 195 /* ---
 196  * System Conf. Reg. & System Protection Reg.
 197  * ---
 198  */
 199
 200 #define CONFIG_SYS_SCR                  0x0003
 201 #define CONFIG_SYS_SPR                  0xffff
 202
 203 /* ---
 204  * Ethernet settings
 205  * ---
 206  */
 207
 208 #define CONFIG_SYS_DISCOVER_PHY
 209 #define CONFIG_SYS_ENET_BD_BASE 0x780000
 210
 211 /*-----------------------------------------------------------------------
 212  * Definitions for initial stack pointer and data area (in internal SRAM)
 213  */
 214 #define CONFIG_SYS_INIT_RAM_ADDR        0x20000000
 215 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000  /* Size of used area in internal SRAM   */
 216 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 217 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 218
 219 /*-----------------------------------------------------------------------
 220  * Start addresses for the final memory configuration
 221  * (Set up by the startup code)
 222  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 223  */
 224 #define CONFIG_SYS_SDRAM_BASE           0x00000000
 225
 226 /*
 227  *-------------------------------------------------------------------------
 228  * RAM SIZE (is defined above)
 229  *-----------------------------------------------------------------------
 230  */
 231
 232 /* #define CONFIG_SYS_SDRAM_SIZE                16 */
 233
 234 /*
 235  *-----------------------------------------------------------------------
 236  */
 237
 238 #define CONFIG_SYS_FLASH_BASE           0xffe00000
 239
 240 #ifdef  CONFIG_MONITOR_IS_IN_RAM
 241 #define CONFIG_SYS_MONITOR_BASE 0x20000
 242 #else
 243 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
 244 #endif
 245
 246 #define CONFIG_SYS_MONITOR_LEN          0x20000
 247 #define CONFIG_SYS_MALLOC_LEN           (256 << 10)
 248 #define CONFIG_SYS_BOOTPARAMS_LEN       64*1024
 249
 250 /*
 251  * For booting Linux, the board info and command line data
 252  * have to be in the first 8 MB of memory, since this is
 253  * the maximum mapped by the Linux kernel during initialization ??
 254  */
 255 #define CONFIG_SYS_BOOTMAPSZ            (8 << 20)       /* Initial Memory map for Linux */
 256
 257 /*-----------------------------------------------------------------------
 258  * FLASH organization
 259  */
 260 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* max number of memory banks           */
 261 #define CONFIG_SYS_MAX_FLASH_SECT       11      /* max number of sectors on one chip    */
 262 #define CONFIG_SYS_FLASH_ERASE_TOUT     1000    /* flash timeout */
 263
 264 /*-----------------------------------------------------------------------
 265  * Cache Configuration
 266  */
 267 #define CONFIG_SYS_CACHELINE_SIZE       16
 268
 269 #define ICACHE_STATUS                   (CONFIG_SYS_INIT_RAM_ADDR + \
 270                                          CONFIG_SYS_INIT_RAM_SIZE - 8)
 271 #define DCACHE_STATUS                   (CONFIG_SYS_INIT_RAM_ADDR + \
 272                                          CONFIG_SYS_INIT_RAM_SIZE - 4)
 273 #define CONFIG_SYS_ICACHE_INV           (CF_CACR_CINV | CF_CACR_INVI)
 274 #define CONFIG_SYS_CACHE_ACR0           (CONFIG_SYS_SDRAM_BASE | \
 275                                          CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
 276                                          CF_ACR_EN | CF_ACR_SM_ALL)
 277 #define CONFIG_SYS_CACHE_ICACR          (CF_CACR_CENB | CF_CACR_CINV | \
 278                                          CF_CACR_DISD | CF_CACR_INVI | \
 279                                          CF_CACR_CEIB | CF_CACR_DCM | \
 280                                          CF_CACR_EUSP)
 281
 282 /*-----------------------------------------------------------------------
 283  * Memory bank definitions
 284  *
 285  * Please refer also to Motorola Coldfire user manual - Chapter XXX
 286  * <http://e-www.motorola.com/files/dsp/doc/ref_manual/MCF5272UM.pdf>
 287  */
 288 #define CONFIG_SYS_BR0_PRELIM           0xFFE00201
 289 #define CONFIG_SYS_OR0_PRELIM           0xFFE00014
 290
 291 #define CONFIG_SYS_BR1_PRELIM           0
 292 #define CONFIG_SYS_OR1_PRELIM           0
 293
 294 #define CONFIG_SYS_BR2_PRELIM           0
 295 #define CONFIG_SYS_OR2_PRELIM           0
 296
 297 #define CONFIG_SYS_BR3_PRELIM           0
 298 #define CONFIG_SYS_OR3_PRELIM           0
 299
 300 #define CONFIG_SYS_BR4_PRELIM           0
 301 #define CONFIG_SYS_OR4_PRELIM           0
 302
 303 #define CONFIG_SYS_BR5_PRELIM           0
 304 #define CONFIG_SYS_OR5_PRELIM           0
 305
 306 #define CONFIG_SYS_BR6_PRELIM           0
 307 #define CONFIG_SYS_OR6_PRELIM           0
 308
 309 #define CONFIG_SYS_BR7_PRELIM           0x00000701
 310 #define CONFIG_SYS_OR7_PRELIM           0xFF00007C
 311
 312 /*-----------------------------------------------------------------------
 313  * LED config
 314  */
 315 #define LED_STAT_0      0xffff /*all LEDs off*/
 316 #define LED_STAT_1      0xfffe
 317 #define LED_STAT_2      0xfffd
 318 #define LED_STAT_3      0xfffb
 319 #define LED_STAT_4      0xfff7
 320 #define LED_STAT_5      0xffef
 321 #define LED_STAT_6      0xffdf
 322 #define LED_STAT_7      0xff00 /*all LEDs on*/
 323
 324 /*-----------------------------------------------------------------------
 325  * Port configuration (GPIO)
 326  */
 327 #define CONFIG_SYS_PACNT                0x00000000              /* PortA control reg.: All pins are external
 328 GPIO*/
 329 #define CONFIG_SYS_PADDR                0x00FF                  /* PortA direction reg.: PA7 to PA0 are outputs
 330 (1^=output, 0^=input) */
 331 #define CONFIG_SYS_PADAT                LED_STAT_0              /* PortA value reg.: Turn all LED off */
 332 #define CONFIG_SYS_PBCNT                0x55554155              /* PortB control reg.: Ethernet/UART
 333 configuration */
 334 #define CONFIG_SYS_PBDDR                0x0000                  /* PortB direction: All pins configured as inputs */
 335 #define CONFIG_SYS_PBDAT                0x0000                  /* PortB value reg. */
 336 #define CONFIG_SYS_PDCNT                0x00000000              /* PortD control reg. */
 337
 338 #endif  /* _CONFIG_COBRA5272_H */