include/configs/ls2080ardb.h

   1 /*
   2  * Copyright 2017 NXP
   3  * Copyright 2015 Freescale Semiconductor
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 #ifndef __LS2_RDB_H
   9 #define __LS2_RDB_H
  10
  11 #include "ls2080a_common.h"
  12
  13 #undef CONFIG_CONS_INDEX
  14 #define CONFIG_CONS_INDEX       2
  15
  16 #ifdef CONFIG_FSL_QSPI
  17 #ifdef CONFIG_TARGET_LS2081ARDB
  18 #define CONFIG_QIXIS_I2C_ACCESS
  19 #endif
  20 #define CONFIG_SYS_I2C_EARLY_INIT
  21 #endif
  22
  23 #define I2C_MUX_CH_VOL_MONITOR          0xa
  24 #define I2C_VOL_MONITOR_ADDR            0x38
  25 #define CONFIG_VOL_MONITOR_IR36021_READ
  26 #define CONFIG_VOL_MONITOR_IR36021_SET
  27
  28 #define CONFIG_VID_FLS_ENV              "ls2080ardb_vdd_mv"
  29 #ifndef CONFIG_SPL_BUILD
  30 #define CONFIG_VID
  31 #endif
  32 /* step the IR regulator in 5mV increments */
  33 #define IR_VDD_STEP_DOWN                5
  34 #define IR_VDD_STEP_UP                  5
  35 /* The lowest and highest voltage allowed for LS2080ARDB */
  36 #define VDD_MV_MIN                      819
  37 #define VDD_MV_MAX                      1212
  38
  39 #ifndef __ASSEMBLY__
  40 unsigned long get_board_sys_clk(void);
  41 #endif
  42
  43 #define CONFIG_SYS_CLK_FREQ             get_board_sys_clk()
  44 #define CONFIG_DDR_CLK_FREQ             133333333
  45 #define COUNTER_FREQUENCY_REAL          (CONFIG_SYS_CLK_FREQ/4)
  46
  47 #define CONFIG_DDR_SPD
  48 #define CONFIG_DDR_ECC
  49 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
  50 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  51 #define SPD_EEPROM_ADDRESS1     0x51
  52 #define SPD_EEPROM_ADDRESS2     0x52
  53 #define SPD_EEPROM_ADDRESS3     0x53
  54 #define SPD_EEPROM_ADDRESS4     0x54
  55 #define SPD_EEPROM_ADDRESS5     0x55
  56 #define SPD_EEPROM_ADDRESS6     0x56    /* dummy address */
  57 #define SPD_EEPROM_ADDRESS      SPD_EEPROM_ADDRESS1
  58 #define CONFIG_SYS_SPD_BUS_NUM  0       /* SPD on I2C bus 0 */
  59 #define CONFIG_DIMM_SLOTS_PER_CTLR              2
  60 #define CONFIG_CHIP_SELECTS_PER_CTRL            4
  61 #ifdef CONFIG_SYS_FSL_HAS_DP_DDR
  62 #define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR       1
  63 #endif
  64 #define CONFIG_FSL_DDR_BIST     /* enable built-in memory test */
  65
  66 /* SATA */
  67 #define CONFIG_SCSI_AHCI_PLAT
  68
  69 #define CONFIG_SYS_SATA1                        AHCI_BASE_ADDR1
  70 #define CONFIG_SYS_SATA2                        AHCI_BASE_ADDR2
  71
  72 #define CONFIG_SYS_SCSI_MAX_SCSI_ID             1
  73 #define CONFIG_SYS_SCSI_MAX_LUN                 1
  74 #define CONFIG_SYS_SCSI_MAX_DEVICE              (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
  75                                                 CONFIG_SYS_SCSI_MAX_LUN)
  76
  77 #ifndef CONFIG_FSL_QSPI
  78 /* undefined CONFIG_FSL_DDR_SYNC_REFRESH for simulator */
  79
  80 #define CONFIG_SYS_NOR0_CSPR_EXT        (0x0)
  81 #define CONFIG_SYS_NOR_AMASK            IFC_AMASK(128*1024*1024)
  82 #define CONFIG_SYS_NOR_AMASK_EARLY      IFC_AMASK(64*1024*1024)
  83
  84 #define CONFIG_SYS_NOR0_CSPR                                    \
  85         (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS)             | \
  86         CSPR_PORT_SIZE_16                                       | \
  87         CSPR_MSEL_NOR                                           | \
  88         CSPR_V)
  89 #define CONFIG_SYS_NOR0_CSPR_EARLY                              \
  90         (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY)       | \
  91         CSPR_PORT_SIZE_16                                       | \
  92         CSPR_MSEL_NOR                                           | \
  93         CSPR_V)
  94 #define CONFIG_SYS_NOR_CSOR     CSOR_NOR_ADM_SHIFT(12)
  95 #define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x4) | \
  96                                 FTIM0_NOR_TEADC(0x5) | \
  97                                 FTIM0_NOR_TEAHC(0x5))
  98 #define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x35) | \
  99                                 FTIM1_NOR_TRAD_NOR(0x1a) |\
 100                                 FTIM1_NOR_TSEQRAD_NOR(0x13))
 101 #define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x4) | \
 102                                 FTIM2_NOR_TCH(0x4) | \
 103                                 FTIM2_NOR_TWPH(0x0E) | \
 104                                 FTIM2_NOR_TWP(0x1c))
 105 #define CONFIG_SYS_NOR_FTIM3    0x04000000
 106 #define CONFIG_SYS_IFC_CCR      0x01000000
 107
 108 #ifdef CONFIG_MTD_NOR_FLASH
 109 #define CONFIG_FLASH_CFI_DRIVER
 110 #define CONFIG_SYS_FLASH_CFI
 111 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 112 #define CONFIG_SYS_FLASH_QUIET_TEST
 113 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 114
 115 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 116 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
 117 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 118 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 119
 120 #define CONFIG_SYS_FLASH_EMPTY_INFO
 121 #define CONFIG_SYS_FLASH_BANKS_LIST     { CONFIG_SYS_FLASH_BASE,\
 122                                          CONFIG_SYS_FLASH_BASE + 0x40000000}
 123 #endif
 124
 125 #define CONFIG_NAND_FSL_IFC
 126 #define CONFIG_SYS_NAND_MAX_ECCPOS      256
 127 #define CONFIG_SYS_NAND_MAX_OOBFREE     2
 128
 129 #define CONFIG_SYS_NAND_CSPR_EXT        (0x0)
 130 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 131                                 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 132                                 | CSPR_MSEL_NAND        /* MSEL = NAND */ \
 133                                 | CSPR_V)
 134 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64 * 1024)
 135
 136 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 137                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 138                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
 139                                 | CSOR_NAND_RAL_3       /* RAL = 3Byes */ \
 140                                 | CSOR_NAND_PGS_4K      /* Page Size = 4K */ \
 141                                 | CSOR_NAND_SPRZ_224    /* Spare size = 224 */ \
 142                                 | CSOR_NAND_PB(128))    /* Pages Per Block 128*/
 143
 144 #define CONFIG_SYS_NAND_ONFI_DETECTION
 145
 146 /* ONFI NAND Flash mode0 Timing Params */
 147 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x0e) | \
 148                                         FTIM0_NAND_TWP(0x30)   | \
 149                                         FTIM0_NAND_TWCHT(0x0e) | \
 150                                         FTIM0_NAND_TWH(0x14))
 151 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x64) | \
 152                                         FTIM1_NAND_TWBE(0xab)  | \
 153                                         FTIM1_NAND_TRR(0x1c)   | \
 154                                         FTIM1_NAND_TRP(0x30))
 155 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x1e) | \
 156                                         FTIM2_NAND_TREH(0x14) | \
 157                                         FTIM2_NAND_TWHRE(0x3c))
 158 #define CONFIG_SYS_NAND_FTIM3           0x0
 159
 160 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 161 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 162 #define CONFIG_MTD_NAND_VERIFY_WRITE
 163
 164 #define CONFIG_SYS_NAND_BLOCK_SIZE      (512 * 1024)
 165 #define CONFIG_FSL_QIXIS        /* use common QIXIS code */
 166 #define QIXIS_LBMAP_SWITCH              0x06
 167 #define QIXIS_LBMAP_MASK                0x0f
 168 #define QIXIS_LBMAP_SHIFT               0
 169 #define QIXIS_LBMAP_DFLTBANK            0x00
 170 #define QIXIS_LBMAP_ALTBANK             0x04
 171 #define QIXIS_LBMAP_NAND                0x09
 172 #define QIXIS_RST_CTL_RESET             0x31
 173 #define QIXIS_RST_CTL_RESET_EN          0x30
 174 #define QIXIS_RCFG_CTL_RECONFIG_IDLE    0x20
 175 #define QIXIS_RCFG_CTL_RECONFIG_START   0x21
 176 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE   0x08
 177 #define QIXIS_RCW_SRC_NAND              0x119
 178 #define QIXIS_RST_FORCE_MEM             0x01
 179
 180 #define CONFIG_SYS_CSPR3_EXT    (0x0)
 181 #define CONFIG_SYS_CSPR3        (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \
 182                                 | CSPR_PORT_SIZE_8 \
 183                                 | CSPR_MSEL_GPCM \
 184                                 | CSPR_V)
 185 #define CONFIG_SYS_CSPR3_FINAL  (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
 186                                 | CSPR_PORT_SIZE_8 \
 187                                 | CSPR_MSEL_GPCM \
 188                                 | CSPR_V)
 189
 190 #define CONFIG_SYS_AMASK3       IFC_AMASK(64*1024)
 191 #define CONFIG_SYS_CSOR3        CSOR_GPCM_ADM_SHIFT(12)
 192 /* QIXIS Timing parameters for IFC CS3 */
 193 #define CONFIG_SYS_CS3_FTIM0            (FTIM0_GPCM_TACSE(0x0e) | \
 194                                         FTIM0_GPCM_TEADC(0x0e) | \
 195                                         FTIM0_GPCM_TEAHC(0x0e))
 196 #define CONFIG_SYS_CS3_FTIM1            (FTIM1_GPCM_TACO(0xff) | \
 197                                         FTIM1_GPCM_TRAD(0x3f))
 198 #define CONFIG_SYS_CS3_FTIM2            (FTIM2_GPCM_TCS(0xf) | \
 199                                         FTIM2_GPCM_TCH(0xf) | \
 200                                         FTIM2_GPCM_TWP(0x3E))
 201 #define CONFIG_SYS_CS3_FTIM3            0x0
 202
 203 #if defined(CONFIG_SPL) && defined(CONFIG_NAND)
 204 #define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 205 #define CONFIG_SYS_CSPR2                CONFIG_SYS_NOR0_CSPR_EARLY
 206 #define CONFIG_SYS_CSPR2_FINAL          CONFIG_SYS_NOR0_CSPR
 207 #define CONFIG_SYS_AMASK2               CONFIG_SYS_NOR_AMASK
 208 #define CONFIG_SYS_CSOR2                CONFIG_SYS_NOR_CSOR
 209 #define CONFIG_SYS_CS2_FTIM0            CONFIG_SYS_NOR_FTIM0
 210 #define CONFIG_SYS_CS2_FTIM1            CONFIG_SYS_NOR_FTIM1
 211 #define CONFIG_SYS_CS2_FTIM2            CONFIG_SYS_NOR_FTIM2
 212 #define CONFIG_SYS_CS2_FTIM3            CONFIG_SYS_NOR_FTIM3
 213 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
 214 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 215 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 216 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 217 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 218 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 219 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 220 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 221
 222 #define CONFIG_ENV_OFFSET               (2048 * 1024)
 223 #define CONFIG_ENV_SECT_SIZE            0x20000
 224 #define CONFIG_ENV_SIZE                 0x2000
 225 #define CONFIG_SPL_PAD_TO               0x80000
 226 #define CONFIG_SYS_NAND_U_BOOT_OFFS     (1024 * 1024)
 227 #define CONFIG_SYS_NAND_U_BOOT_SIZE     (512 * 1024)
 228 #else
 229 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 230 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR_EARLY
 231 #define CONFIG_SYS_CSPR0_FINAL          CONFIG_SYS_NOR0_CSPR
 232 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
 233 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
 234 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
 235 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
 236 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
 237 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
 238 #define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_NAND_CSPR_EXT
 239 #define CONFIG_SYS_CSPR2                CONFIG_SYS_NAND_CSPR
 240 #define CONFIG_SYS_AMASK2               CONFIG_SYS_NAND_AMASK
 241 #define CONFIG_SYS_CSOR2                CONFIG_SYS_NAND_CSOR
 242 #define CONFIG_SYS_CS2_FTIM0            CONFIG_SYS_NAND_FTIM0
 243 #define CONFIG_SYS_CS2_FTIM1            CONFIG_SYS_NAND_FTIM1
 244 #define CONFIG_SYS_CS2_FTIM2            CONFIG_SYS_NAND_FTIM2
 245 #define CONFIG_SYS_CS2_FTIM3            CONFIG_SYS_NAND_FTIM3
 246
 247 #define CONFIG_ENV_ADDR                 (CONFIG_SYS_FLASH_BASE + 0x300000)
 248 #define CONFIG_ENV_SECT_SIZE            0x20000
 249 #define CONFIG_ENV_SIZE                 0x2000
 250 #endif
 251
 252 /* Debug Server firmware */
 253 #define CONFIG_SYS_DEBUG_SERVER_FW_IN_NOR
 254 #define CONFIG_SYS_DEBUG_SERVER_FW_ADDR 0x580D00000ULL
 255 #endif
 256 #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
 257
 258 #ifdef CONFIG_TARGET_LS2081ARDB
 259 #define CONFIG_FSL_QIXIS        /* use common QIXIS code */
 260 #define QIXIS_QMAP_MASK                 0x07
 261 #define QIXIS_QMAP_SHIFT                5
 262 #define QIXIS_LBMAP_DFLTBANK            0x00
 263 #define QIXIS_LBMAP_QSPI                0x00
 264 #define QIXIS_RCW_SRC_QSPI              0x62
 265 #define QIXIS_LBMAP_ALTBANK             0x20
 266 #define QIXIS_RST_CTL_RESET             0x31
 267 #define QIXIS_RCFG_CTL_RECONFIG_IDLE    0x20
 268 #define QIXIS_RCFG_CTL_RECONFIG_START   0x21
 269 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE   0x08
 270 #define QIXIS_LBMAP_MASK                0x0f
 271 #define QIXIS_RST_CTL_RESET_EN          0x30
 272 #endif
 273
 274 /*
 275  * I2C
 276  */
 277 #ifdef CONFIG_TARGET_LS2081ARDB
 278 #define CONFIG_SYS_I2C_FPGA_ADDR        0x66
 279 #endif
 280 #define I2C_MUX_PCA_ADDR                0x75
 281 #define I2C_MUX_PCA_ADDR_PRI            0x75 /* Primary Mux*/
 282
 283 /* I2C bus multiplexer */
 284 #define I2C_MUX_CH_DEFAULT      0x8
 285
 286 /* SPI */
 287 #if defined(CONFIG_FSL_QSPI) || defined(CONFIG_FSL_DSPI)
 288 #define CONFIG_SPI_FLASH
 289 #ifdef CONFIG_FSL_DSPI
 290 #define CONFIG_SPI_FLASH_STMICRO
 291 #endif
 292 #ifdef CONFIG_FSL_QSPI
 293 #define CONFIG_SPI_FLASH_SPANSION
 294 #endif
 295 #define FSL_QSPI_FLASH_SIZE             SZ_64M  /* 64MB */
 296 #define FSL_QSPI_FLASH_NUM              2
 297 #endif
 298
 299 /*
 300  * RTC configuration
 301  */
 302 #define RTC
 303 #ifdef CONFIG_TARGET_LS2081ARDB
 304 #define CONFIG_RTC_PCF8563              1
 305 #define CONFIG_SYS_I2C_RTC_ADDR         0x51
 306 #else
 307 #define CONFIG_RTC_DS3231               1
 308 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
 309 #endif
 310
 311 /* EEPROM */
 312 #define CONFIG_ID_EEPROM
 313 #define CONFIG_SYS_I2C_EEPROM_NXID
 314 #define CONFIG_SYS_EEPROM_BUS_NUM       0
 315 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x57
 316 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  1
 317 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
 318 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
 319
 320 #define CONFIG_FSL_MEMAC
 321
 322 #ifdef CONFIG_PCI
 323 #define CONFIG_PCI_SCAN_SHOW
 324 #endif
 325
 326 /*  MMC  */
 327 #ifdef CONFIG_MMC
 328 #define CONFIG_FSL_ESDHC
 329 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
 330 #endif
 331
 332 #define CONFIG_MISC_INIT_R
 333
 334 #include <config_distro_defaults.h>
 335
 336 #define BOOT_TARGET_DEVICES(func) \
 337         func(USB, usb, 0) \
 338         func(MMC, mmc, 0) \
 339         func(SCSI, scsi, 0) \
 340         func(DHCP, dhcp, na)
 341 #include <config_distro_bootcmd.h>
 342
 343 #ifdef CONFIG_QSPI_BOOT
 344 #define MC_INIT_CMD                             \
 345         "mcinitcmd=env exists secureboot && "   \
 346         "esbc_validate 0x20700000 && "          \
 347         "esbc_validate 0x20740000;"             \
 348         "fsl_mc start mc 0x20a00000 0x20e00000 \0"
 349 #elif defined(CONFIG_SD_BOOT)
 350 #define MC_INIT_CMD                             \
 351         "mcinitcmd=mmcinfo;mmc read 0x80000000 0x5000 0x800;" \
 352         "mmc read 0x80100000 0x7000 0x800;"     \
 353         "env exists secureboot && "             \
 354         "mmc read 0x80700000 0x3800 0x10 && "   \
 355         "mmc read 0x80740000 0x3A00 0x10 && "   \
 356         "esbc_validate 0x80700000 && "          \
 357         "esbc_validate 0x80740000 ;"            \
 358         "fsl_mc start mc 0x80000000 0x80100000\0" \
 359         "mcmemsize=0x70000000\0"
 360 #else
 361 #define MC_INIT_CMD                             \
 362         "mcinitcmd=env exists secureboot && "   \
 363         "esbc_validate 0x580700000 && "         \
 364         "esbc_validate 0x580740000; "           \
 365         "fsl_mc start mc 0x580a00000 0x580e00000 \0"
 366 #endif
 367
 368 /* Initial environment variables */
 369 #undef CONFIG_EXTRA_ENV_SETTINGS
 370 #define CONFIG_EXTRA_ENV_SETTINGS               \
 371         "hwconfig=fsl_ddr:bank_intlv=auto\0"    \
 372         "ramdisk_addr=0x800000\0"               \
 373         "ramdisk_size=0x2000000\0"              \
 374         "fdt_high=0xa0000000\0"                 \
 375         "initrd_high=0xffffffffffffffff\0"      \
 376         "fdt_addr=0x64f00000\0"                 \
 377         "kernel_addr=0x65000000\0"              \
 378         "kernel_start=0x1000000\0"              \
 379         "kernelheader_start=0x800000\0"         \
 380         "scriptaddr=0x80000000\0"               \
 381         "scripthdraddr=0x80080000\0"            \
 382         "fdtheader_addr_r=0x80100000\0"         \
 383         "kernelheader_addr_r=0x80200000\0"      \
 384         "kernelheader_addr=0x580800000\0"       \
 385         "kernel_addr_r=0x81000000\0"            \
 386         "kernelheader_size=0x40000\0"           \
 387         "fdt_addr_r=0x90000000\0"               \
 388         "load_addr=0xa0000000\0"                \
 389         "kernel_size=0x2800000\0"               \
 390         "kernel_addr_sd=0x8000\0"               \
 391         "kernel_size_sd=0x14000\0"              \
 392         "console=ttyAMA0,38400n8\0"             \
 393         "mcmemsize=0x70000000\0"                \
 394         "sd_bootcmd=echo Trying load from SD ..;" \
 395         "mmcinfo; mmc read $load_addr "         \
 396         "$kernel_addr_sd $kernel_size_sd && "   \
 397         "bootm $load_addr#$board\0"             \
 398         MC_INIT_CMD                             \
 399         BOOTENV                                 \
 400         "boot_scripts=ls2088ardb_boot.scr\0"    \
 401         "boot_script_hdr=hdr_ls2088ardb_bs.out\0"       \
 402         "scan_dev_for_boot_part="               \
 403                 "part list ${devtype} ${devnum} devplist; "     \
 404                 "env exists devplist || setenv devplist 1; "    \
 405                 "for distro_bootpart in ${devplist}; do "       \
 406                         "if fstype ${devtype} "                 \
 407                                 "${devnum}:${distro_bootpart} " \
 408                                 "bootfstype; then "             \
 409                                 "run scan_dev_for_boot; "       \
 410                         "fi; "                                  \
 411                 "done\0"                                        \
 412         "scan_dev_for_boot="                                    \
 413                 "echo Scanning ${devtype} "                     \
 414                         "${devnum}:${distro_bootpart}...; "     \
 415                 "for prefix in ${boot_prefixes}; do "           \
 416                         "run scan_dev_for_scripts; "            \
 417                 "done;\0"                                       \
 418         "boot_a_script="                                        \
 419                 "load ${devtype} ${devnum}:${distro_bootpart} " \
 420                         "${scriptaddr} ${prefix}${script}; "    \
 421                 "env exists secureboot && load ${devtype} "     \
 422                         "${devnum}:${distro_bootpart} "         \
 423                         "${scripthdraddr} ${prefix}${boot_script_hdr} " \
 424                         "&& esbc_validate ${scripthdraddr};"    \
 425                 "source ${scriptaddr}\0"                        \
 426         "qspi_bootcmd=echo Trying load from qspi..;"            \
 427                 "sf probe && sf read $load_addr "               \
 428                 "$kernel_start $kernel_size ; env exists secureboot &&" \
 429                 "sf read $kernelheader_addr_r $kernelheader_start "     \
 430                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
 431                 " bootm $load_addr#$board\0"                    \
 432         "nor_bootcmd=echo Trying load from nor..;"              \
 433                 "cp.b $kernel_addr $load_addr "                 \
 434                 "$kernel_size ; env exists secureboot && "      \
 435                 "cp.b $kernelheader_addr $kernelheader_addr_r " \
 436                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
 437                 "bootm $load_addr#$board\0"
 438
 439 #undef CONFIG_BOOTCOMMAND
 440 #ifdef CONFIG_QSPI_BOOT
 441 /* Try to boot an on-QSPI kernel first, then do normal distro boot */
 442 #define CONFIG_BOOTCOMMAND                                              \
 443                         "env exists mcinitcmd && env exists secureboot "\
 444                         "&& esbc_validate 0x20780000; "                 \
 445                         "env exists mcinitcmd && "                      \
 446                         "fsl_mc lazyapply dpl 0x20d00000; "             \
 447                         "run distro_bootcmd;env exists secureboot "     \
 448                         " && esbc_halt;run qspi_bootcmd; "
 449 #elif defined(CONFIG_SD_BOOT)
 450 /* Try to boot an on-SD kernel first, then do normal distro boot */
 451 #define CONFIG_BOOTCOMMAND                                              \
 452                         "env exists mcinitcmd && env exists secureboot "\
 453                         "&& mmcinfo && mmc read $load_addr 0x3c00 0x800 " \
 454                         "&& esbc_validate $load_addr; "                 \
 455                         "env exists mcinitcmd && run mcinitcmd "        \
 456                         "&& mmc read 0x88000000 0x6800 0x800 "          \
 457                         "&& fsl_mc lazyapply dpl 0x88000000; "          \
 458                         "run distro_bootcmd;env exists secureboot "     \
 459                         "&& esbc_halt;run sd_bootcmd;"
 460 #else
 461 /* Try to boot an on-NOR kernel first, then do normal distro boot */
 462 #define CONFIG_BOOTCOMMAND                                              \
 463                         "env exists mcinitcmd && env exists secureboot "\
 464                         "&& esbc_validate 0x580780000; env exists mcinitcmd "\
 465                         "&& fsl_mc lazyapply dpl 0x580d00000;"          \
 466                         "run distro_bootcmd; env exists secureboot "    \
 467                         "&& esbc_halt; run nor_bootcmd;"
 468 #endif
 469
 470 /* MAC/PHY configuration */
 471 #ifdef CONFIG_FSL_MC_ENET
 472 #define CONFIG_PHYLIB_10G
 473 #define CONFIG_PHY_AQUANTIA
 474 #define CONFIG_PHY_CORTINA
 475 #define CONFIG_SYS_CORTINA_FW_IN_NOR
 476 #ifdef CONFIG_QSPI_BOOT
 477 #define CONFIG_CORTINA_FW_ADDR          0x20980000
 478 #else
 479 #define CONFIG_CORTINA_FW_ADDR          0x580980000
 480 #endif
 481 #define CONFIG_CORTINA_FW_LENGTH        0x40000
 482
 483 #define CORTINA_PHY_ADDR1       0x10
 484 #define CORTINA_PHY_ADDR2       0x11
 485 #define CORTINA_PHY_ADDR3       0x12
 486 #define CORTINA_PHY_ADDR4       0x13
 487 #define AQ_PHY_ADDR1            0x00
 488 #define AQ_PHY_ADDR2            0x01
 489 #define AQ_PHY_ADDR3            0x02
 490 #define AQ_PHY_ADDR4            0x03
 491 #define AQR405_IRQ_MASK         0x36
 492
 493 #define CONFIG_MII
 494 #define CONFIG_ETHPRIME         "DPMAC1@xgmii"
 495 #define CONFIG_PHY_AQUANTIA
 496 #endif
 497
 498 #include <asm/fsl_secure_boot.h>
 499
 500 #endif /* __LS2_RDB_H */