include/configs/motionpro.h

   1 /*
   2  * (C) Copyright 2003-2007
   3  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
   4  *
   5  * Based on Motion-PRO board config file by Robert McCullough, rob@promessinc.com
   6  *
   7  * SPDX-License-Identifier:     GPL-2.0+
   8  */
   9
  10 #ifndef __CONFIG_H
  11 #define __CONFIG_H
  12
  13 /*
  14  * High Level Configuration Options
  15  */
  16
  17 /* CPU and board */
  18 #define CONFIG_MPC5200          1       /* This is a MPC5200 CPU */
  19 #define CONFIG_MOTIONPRO        1       /* ... on Promess Motion-PRO board */
  20 #define CONFIG_DISPLAY_BOARDINFO
  21
  22 #define CONFIG_HIGH_BATS        1       /* High BATs supported */
  23
  24 #define CONFIG_SYS_TEXT_BASE    0xfff00000
  25
  26 /*
  27  * BOOTP options
  28  */
  29 #define CONFIG_BOOTP_BOOTFILESIZE
  30 #define CONFIG_BOOTP_BOOTPATH
  31 #define CONFIG_BOOTP_GATEWAY
  32 #define CONFIG_BOOTP_HOSTNAME
  33
  34 /*
  35  * Command line configuration.
  36  */
  37 #define CONFIG_CMD_ASKENV
  38 #define CONFIG_CMD_BEDBUG
  39 #define CONFIG_CMD_DATE
  40 #define CONFIG_CMD_DHCP
  41 #define CONFIG_CMD_DTT
  42 #define CONFIG_CMD_EEPROM
  43 #define CONFIG_CMD_FAT
  44 #define CONFIG_CMD_I2C
  45 #define CONFIG_CMD_IDE
  46 #define CONFIG_CMD_IMMAP
  47 #define CONFIG_CMD_JFFS2
  48 #define CONFIG_CMD_MII
  49 #define CONFIG_CMD_PING
  50 #define CONFIG_CMD_REGINFO
  51
  52 /*
  53  * Serial console configuration
  54  */
  55 #define CONFIG_PSC_CONSOLE      1       /* console is on PSC1 */
  56 #define CONFIG_NETCONSOLE       1       /* network console */
  57 #define CONFIG_BAUDRATE         115200
  58 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200, 230400 }
  59
  60 /*
  61  * Ethernet configuration
  62  */
  63 #define CONFIG_MPC5xxx_FEC      1
  64 #define CONFIG_MPC5xxx_FEC_MII100
  65 #define CONFIG_PHY_ADDR         0x2
  66 #define CONFIG_PHY_TYPE         0x79c874
  67 #define CONFIG_RESET_PHY_R      1
  68
  69 /*
  70  * Autobooting
  71  */
  72 #define CONFIG_BOOTDELAY        2       /* autoboot after 2 seconds */
  73 #undef CONFIG_BOOTARGS
  74
  75 #define CONFIG_CMDLINE_EDITING          1       /* add command line history     */
  76 #define CONFIG_SYS_HUSH_PARSER          1       /* use "hush" command parser    */
  77 #define CONFIG_SYS_PROMPT_HUSH_PS2      "> "
  78
  79 #define CONFIG_VERSION_VARIABLE 1       /* include version env variable */
  80
  81 /*
  82  * Default environment settings
  83  */
  84 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
  85         "netdev=eth0\0"                                                 \
  86         "hostname=motionpro\0"                                          \
  87         "netmask=255.255.255.0\0"                                       \
  88         "ipaddr=192.168.1.106\0"                                        \
  89         "serverip=192.168.1.100\0"                                      \
  90         "gatewayip=192.168.1.100\0"                                     \
  91         "console=ttyPSC0,115200\0"                                      \
  92         "u-boot_addr=400000\0"                                          \
  93         "kernel_addr=400000\0"                                          \
  94         "fdt_addr=700000\0"                                             \
  95         "ramdisk_addr=800000\0"                                         \
  96         "multi_image_addr=800000\0"                                     \
  97         "rootpath=/opt/eldk-4.2/ppc_6xx\0"                              \
  98         "u-boot=/tftpboot/motionpro/u-boot.bin\0"                       \
  99         "bootfile=/tftpboot/motionpro/uImage\0"                         \
 100         "fdt_file=/tftpboot/motionpro/motionpro.dtb\0"                  \
 101         "ramdisk_file=/tftpboot/motionpro/uRamdisk\0"                   \
 102         "multi_image_file=kernel+initrd+dtb.img\0"                      \
 103         "load=tftp ${u-boot_addr} ${u-boot}\0"                          \
 104         "update=prot off fff00000 +${filesize};"                        \
 105                 "era fff00000 +${filesize}; "                           \
 106                 "cp.b ${u-boot_addr} fff00000 ${filesize};"             \
 107                 "prot on fff00000 +${filesize}\0"                       \
 108         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
 109         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 110                 "nfsroot=${serverip}:${rootpath}\0"                     \
 111         "fat_args=setenv bootargs root=/dev/sda rw\0"                   \
 112         "mtdids=nor0=ff000000.flash\0"                                  \
 113         "mtdparts=ff000000.flash:13m(fs),2m(kernel),384k(uboot),"       \
 114                                 "128k(env),128k(redund_env),"           \
 115                                 "128k(dtb),128k(user_data)\0"           \
 116         "addcons=setenv bootargs ${bootargs} console=${console}\0"      \
 117         "addmtd=setenv bootargs ${bootargs} mtdparts=${mtdparts}\0"     \
 118         "addip=setenv bootargs ${bootargs} "                            \
 119                 "ip=${ipaddr}:${serverip}:${gatewayip}:"                \
 120                 "${netmask}:${hostname}:${netdev}:off panic=1 "         \
 121                 "console=${console}\0"                                  \
 122         "net_nfs=tftp ${kernel_addr} ${bootfile}; "                     \
 123                 "tftp ${fdt_addr} ${fdt_file}; "                        \
 124                 "run nfsargs addip addmtd; "                            \
 125                 "bootm ${kernel_addr} - ${fdt_addr}\0"                  \
 126         "net_self=tftp ${kernel_addr} ${bootfile}; "                    \
 127                 "tftp ${fdt_addr} ${fdt_file}; "                        \
 128                 "tftp ${ramdisk_addr} ${ramdisk_file}; "                \
 129                 "nfs ${ramdisk_addr} ${serverip}:${rootpath}/images/uRamdisk; " \
 130                 "run ramargs addip addcons addmtd; "                    \
 131                 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"    \
 132         "fat_multi=run fat_args addip addmtd; fatload ide 0:1 "         \
 133                 "${multi_image_addr} ${multi_image_file}; "             \
 134                 "bootm ${multi_image_addr}\0"                           \
 135         ""
 136 #define CONFIG_BOOTCOMMAND      "run fat_multi"
 137
 138 /*
 139  * do board-specific init
 140  */
 141 #define CONFIG_BOARD_EARLY_INIT_R       1
 142
 143 /*
 144  * Low level configuration
 145  */
 146
 147 /*
 148  * Clock configuration: SYS_XTALIN = 33MHz
 149  */
 150 #define CONFIG_SYS_MPC5XXX_CLKIN        33000000
 151
 152 /*
 153  * Set IPB speed to 100MHz
 154  */
 155 #define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK
 156
 157 /*
 158  * Memory map
 159  */
 160 /*
 161  * Warning!!! with the current BestComm Task, MBAR MUST BE set to 0xf0000000.
 162  * Setting MBAR to otherwise will cause system hang when using SmartDMA such
 163  * as network commands.
 164  */
 165 #define CONFIG_SYS_MBAR                 0xf0000000
 166 #define CONFIG_SYS_SDRAM_BASE           0x00000000
 167
 168 /*
 169  * If building for running out of SDRAM, then MBAR has been set up beforehand
 170  * (e.g., by the BDI). Otherwise we must specify the default boot-up value of
 171  * MBAR, as given in the doccumentation.
 172  */
 173 #if CONFIG_SYS_TEXT_BASE == 0x00100000
 174 #define CONFIG_SYS_DEFAULT_MBAR 0xf0000000
 175 #else /* CONFIG_SYS_TEXT_BASE != 0x00100000 */
 176 #define CONFIG_SYS_DEFAULT_MBAR 0x80000000
 177 #define CONFIG_SYS_LOWBOOT              1
 178 #endif /* CONFIG_SYS_TEXT_BASE == 0x00100000 */
 179
 180 /* Use SRAM until RAM will be available */
 181 #define CONFIG_SYS_INIT_RAM_ADDR        MPC5XXX_SRAM
 182 #define CONFIG_SYS_INIT_RAM_SIZE        MPC5XXX_SRAM_SIZE
 183
 184 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 185 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 186
 187 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
 188 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 189 #define CONFIG_SYS_RAMBOOT              1
 190 #endif
 191
 192 #define CONFIG_SYS_MONITOR_LEN          (384 << 10)     /* 384 kB for Monitor */
 193 #define CONFIG_SYS_MALLOC_LEN           (1024 << 10)    /* 1 MiB for malloc() */
 194 #define CONFIG_SYS_BOOTMAPSZ            (8 << 20)       /* initial mem map for Linux */
 195
 196 /*
 197  * Chip selects configuration
 198  */
 199 /* Boot Chipselect */
 200 #define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
 201 #define CONFIG_SYS_BOOTCS_SIZE          CONFIG_SYS_FLASH_SIZE
 202 #define CONFIG_SYS_BOOTCS_CFG           0x00045D00
 203
 204 /* Flash memory addressing */
 205 #define CONFIG_SYS_CS0_START            CONFIG_SYS_FLASH_BASE
 206 #define CONFIG_SYS_CS0_SIZE             CONFIG_SYS_FLASH_SIZE
 207 #define CONFIG_SYS_CS0_CFG              CONFIG_SYS_BOOTCS_CFG
 208
 209 /* Dual Port SRAM -- Kollmorgen Drive memory addressing */
 210 #define CONFIG_SYS_CS1_START            0x50000000
 211 #define CONFIG_SYS_CS1_SIZE             0x10000
 212 #define CONFIG_SYS_CS1_CFG              0x05055800
 213
 214 /* Local register access */
 215 #define CONFIG_SYS_CS2_START            0x50010000
 216 #define CONFIG_SYS_CS2_SIZE             0x10000
 217 #define CONFIG_SYS_CS2_CFG              0x05055800
 218
 219 /* Anybus CompactCom Module memory addressing */
 220 #define CONFIG_SYS_CS3_START            0x50020000
 221 #define CONFIG_SYS_CS3_SIZE             0x10000
 222 #define CONFIG_SYS_CS3_CFG              0x05055800
 223
 224 /* No burst and dead cycle = 2 for all CSs */
 225 #define CONFIG_SYS_CS_BURST             0x00000000
 226 #define CONFIG_SYS_CS_DEADCYCLE 0x22222222
 227
 228 /*
 229  * SDRAM configuration
 230  */
 231 /* 2 x MT48LC16M16A2BG-75 IT:D, CASL 3, 32 bit data bus */
 232 #define SDRAM_CONFIG1           0x62322900
 233 #define SDRAM_CONFIG2           0x88c70000
 234 #define SDRAM_CONTROL           0x504f0000
 235 #define SDRAM_MODE              0x00cd0000
 236
 237 /*
 238  * Flash configuration
 239  */
 240 #define CONFIG_SYS_FLASH_CFI            1       /* Flash is CFI conformant */
 241 #define CONFIG_FLASH_CFI_DRIVER 1
 242 #define CONFIG_SYS_FLASH_BASE           0xff000000
 243 #define CONFIG_SYS_FLASH_SIZE           0x01000000
 244 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* max num of memory banks */
 245 #define CONFIG_SYS_FLASH_BANKS_LIST     { CONFIG_SYS_FLASH_BASE }
 246 #define CONFIG_SYS_MAX_FLASH_SECT       128     /* max num of sects on one chip */
 247 #define CONFIG_FLASH_16BIT              /* Flash is 16-bit */
 248
 249 /*
 250  * MTD configuration
 251  */
 252 #define CONFIG_CMD_MTDPARTS
 253 #define CONFIG_MTD_DEVICE               /* needed for mtdparts commands */
 254 #define CONFIG_FLASH_CFI_MTD
 255 #define MTDIDS_DEFAULT          "nor0=motionpro-0"
 256 #define MTDPARTS_DEFAULT        "mtdparts=motionpro-0:"                   \
 257                                         "13m(fs),2m(kernel),384k(uboot)," \
 258                                         "128k(env),128k(redund_env),"     \
 259                                         "128k(dtb),-(user_data)"
 260
 261 /*
 262  * IDE/ATA configuration
 263  */
 264 #define CONFIG_SYS_ATA_BASE_ADDR        MPC5XXX_ATA
 265 #define CONFIG_SYS_IDE_MAXBUS           1
 266 #define CONFIG_SYS_IDE_MAXDEVICE        1
 267 #define CONFIG_IDE_PREINIT
 268
 269 #define CONFIG_SYS_ATA_DATA_OFFSET      0x0060
 270 #define CONFIG_SYS_ATA_REG_OFFSET       CONFIG_SYS_ATA_DATA_OFFSET
 271 #define CONFIG_SYS_ATA_STRIDE           4
 272 #define CONFIG_DOS_PARTITION
 273
 274 /*
 275  * I2C configuration
 276  */
 277 #define CONFIG_HARD_I2C         1       /* I2C with hardware support */
 278 #define CONFIG_SYS_I2C_MODULE           2       /* select I2C module #2 */
 279 #define CONFIG_SYS_I2C_SPEED            100000  /* 100 kHz */
 280 #define CONFIG_SYS_I2C_SLAVE            0x7F
 281
 282 /*
 283  * EEPROM configuration
 284  */
 285 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          1
 286 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       1       /* 2 bytes per write cycle */
 287 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   5       /* 2ms/cycle + 3ms extra */
 288
 289 /*
 290  * RTC configuration
 291  */
 292 #define CONFIG_RTC_DS1337       1
 293 #define CONFIG_SYS_I2C_RTC_ADDR 0x68
 294
 295 /*
 296  * Status LED configuration
 297  */
 298 #define CONFIG_STATUS_LED               /* Status LED enabled */
 299 #define CONFIG_BOARD_SPECIFIC_LED
 300
 301 #define ENABLE_GPIO_OUT         0x00000024
 302 #define LED_ON                  0x00000010
 303
 304 #ifndef __ASSEMBLY__
 305 /*
 306  * In case of Motion-PRO, a LED is identified by its corresponding
 307  * GPT Enable and Mode Select Register.
 308  */
 309 typedef volatile unsigned long * led_id_t;
 310
 311 extern void __led_init(led_id_t id, int state);
 312 extern void __led_toggle(led_id_t id);
 313 extern void __led_set(led_id_t id, int state);
 314 #endif /* __ASSEMBLY__ */
 315
 316 /*
 317  * Temperature sensor
 318  */
 319 #define CONFIG_DTT_LM75         1
 320 #define CONFIG_DTT_SENSORS      { 0x49 }
 321
 322 /*
 323  * Environment settings
 324  */
 325 #define CONFIG_ENV_IS_IN_FLASH  1
 326 /* This has to be a multiple of the Flash sector size */
 327 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 328 #define CONFIG_ENV_SIZE         0x1000
 329 #define CONFIG_ENV_SECT_SIZE    0x20000
 330
 331 /* Configuration of redundant environment */
 332 #define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
 333 #define CONFIG_ENV_SIZE_REDUND  (CONFIG_ENV_SIZE)
 334
 335 /*
 336  * Pin multiplexing configuration
 337  */
 338
 339 /* PSC1: UART1
 340  * PSC2: GPIO (default)
 341  * PSC3: GPIO (default)
 342  * USB: 2xUART4/5
 343  * Ethernet: Ethernet 100Mbit with MD
 344  * Timer: CAN2/GPIO
 345  * PSC6/IRDA: GPIO (default)
 346  */
 347 #define CONFIG_SYS_GPS_PORT_CONFIG      0x1105a004
 348
 349 /*
 350  * Motion-PRO's CPLD revision control register
 351  */
 352 #define CPLD_REV_REGISTER       (CONFIG_SYS_CS2_START + 0x06)
 353
 354 /*
 355  * Miscellaneous configurable options
 356  */
 357 #define CONFIG_SYS_LONGHELP                     /* undef to save memory    */
 358 #define CONFIG_SYS_CBSIZE               1024    /* Console I/O Buffer Size */
 359 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)      /* Print Buffer Size */
 360 #define CONFIG_SYS_MAXARGS              16              /* max number of command args */
 361 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size */
 362
 363 #define CONFIG_SYS_MEMTEST_START        0x00100000      /* memtest works on */
 364 #define CONFIG_SYS_MEMTEST_END          0x03e00000      /* 1 ... 62 MiB in DRAM */
 365 #define CONFIG_SYS_ALT_MEMTEST
 366
 367 #define CONFIG_SYS_LOAD_ADDR            0x200000        /* default kernel load addr */
 368
 369 /*
 370  * Various low-level settings
 371  */
 372 #define CONFIG_SYS_HID0_INIT            HID0_ICE | HID0_ICFI
 373 #define CONFIG_SYS_HID0_FINAL           HID0_ICE
 374
 375 #define CONFIG_SYS_CACHELINE_SIZE       32      /* For MPC5xxx CPUs */
 376
 377 /* Not needed for MPC 5xxx U-Boot, but used by tools/updater */
 378 #define CONFIG_SYS_RESET_ADDRESS        0xfff00100
 379
 380 /* pass open firmware flat tree */
 381 #define CONFIG_OF_BOARD_SETUP   1
 382
 383 #define OF_CPU                  "PowerPC,5200@0"
 384 #define OF_SOC                  "soc5200@f0000000"
 385 #define OF_TBCLK                (bd->bi_busfreq / 4)
 386 #define OF_STDOUT_PATH          "/soc5200@f0000000/serial@2000"
 387
 388 #endif /* __CONFIG_H */