include/configs/mpc5121ads.h

   1 /*
   2  * (C) Copyright 2007-2009 DENX Software Engineering
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 /*
   8  * MPC5121ADS board configuration file
   9  */
  10
  11 #ifndef __CONFIG_H
  12 #define __CONFIG_H
  13
  14 #define CONFIG_MPC5121ADS 1
  15 #define CONFIG_DISPLAY_BOARDINFO
  16
  17 /*
  18  * Memory map for the MPC5121ADS board:
  19  *
  20  * 0x0000_0000 - 0x0FFF_FFFF    DDR RAM (256 MB)
  21  * 0x3000_0000 - 0x3001_FFFF    SRAM (128 KB)
  22  * 0x8000_0000 - 0x803F_FFFF    IMMR (4 MB)
  23  * 0x8200_0000 - 0x8200_001F    CPLD (32 B)
  24  * 0x8400_0000 - 0x82FF_FFFF    PCI I/O space (16 MB)
  25  * 0xA000_0000 - 0xAFFF_FFFF    PCI memory space (256 MB)
  26  * 0xB000_0000 - 0xBFFF_FFFF    PCI memory mapped I/O space (256 MB)
  27  * 0xFC00_0000 - 0xFFFF_FFFF    NOR Boot FLASH (64 MB)
  28  */
  29
  30 /*
  31  * High Level Configuration Options
  32  */
  33 #define CONFIG_E300             1       /* E300 Family */
  34
  35 #define CONFIG_SYS_TEXT_BASE    0xFFF00000
  36
  37 /* video */
  38 #ifdef CONFIG_FSL_DIU_FB
  39 #define CONFIG_SYS_DIU_ADDR     (CONFIG_SYS_IMMR + 0x2100)
  40 #define CONFIG_VIDEO
  41 #define CONFIG_CMD_BMP
  42 #define CONFIG_CFB_CONSOLE
  43 #define CONFIG_VIDEO_SW_CURSOR
  44 #define CONFIG_VGA_AS_SINGLE_DEVICE
  45 #define CONFIG_VIDEO_LOGO
  46 #define CONFIG_VIDEO_BMP_LOGO
  47 #endif
  48
  49 /* CONFIG_PCI is defined at config time */
  50
  51 #ifdef CONFIG_MPC5121ADS_REV2
  52 #define CONFIG_SYS_MPC512X_CLKIN        66000000        /* in Hz */
  53 #else
  54 #define CONFIG_SYS_MPC512X_CLKIN        33333333        /* in Hz */
  55 #define CONFIG_PCI
  56 #endif
  57
  58 #define CONFIG_BOARD_EARLY_INIT_F               /* call board_early_init_f() */
  59 #define CONFIG_MISC_INIT_R
  60
  61 #define CONFIG_SYS_IMMR         0x80000000
  62
  63 #define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest region */
  64 #define CONFIG_SYS_MEMTEST_END          0x00400000
  65
  66 /*
  67  * DDR Setup - manually set all parameters as there's no SPD etc.
  68  */
  69 #ifdef CONFIG_MPC5121ADS_REV2
  70 #define CONFIG_SYS_DDR_SIZE             256             /* MB */
  71 #else
  72 #define CONFIG_SYS_DDR_SIZE             512             /* MB */
  73 #endif
  74 #define CONFIG_SYS_DDR_BASE             0x00000000      /* DDR is system memory*/
  75 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_BASE
  76 #define CONFIG_SYS_MAX_RAM_SIZE         0x20000000
  77
  78 #define CONFIG_SYS_IOCTRL_MUX_DDR       0x00000036
  79
  80 /* DDR Controller Configuration
  81  *
  82  * SYS_CFG:
  83  *      [31:31] MDDRC Soft Reset:       Diabled
  84  *      [30:30] DRAM CKE pin:           Enabled
  85  *      [29:29] DRAM CLK:               Enabled
  86  *      [28:28] Command Mode:           Enabled (For initialization only)
  87  *      [27:25] DRAM Row Select:        dram_row[15:0] = magenta_address[25:10]
  88  *      [24:21] DRAM Bank Select:       dram_bank[1:0] = magenta_address[11:10]
  89  *      [20:19] Read Test:              DON'T USE
  90  *      [18:18] Self Refresh:           Enabled
  91  *      [17:17] 16bit Mode:             Disabled
  92  *      [16:13] Ready Delay:            2
  93  *      [12:12] Half DQS Delay:         Disabled
  94  *      [11:11] Quarter DQS Delay:      Disabled
  95  *      [10:08] Write Delay:            2
  96  *      [07:07] Early ODT:              Disabled
  97  *      [06:06] On DIE Termination:     Disabled
  98  *      [05:05] FIFO Overflow Clear:    DON'T USE here
  99  *      [04:04] FIFO Underflow Clear:   DON'T USE here
 100  *      [03:03] FIFO Overflow Pending:  DON'T USE here
 101  *      [02:02] FIFO Underlfow Pending: DON'T USE here
 102  *      [01:01] FIFO Overlfow Enabled:  Enabled
 103  *      [00:00] FIFO Underflow Enabled: Enabled
 104  * TIME_CFG0
 105  *      [31:16] DRAM Refresh Time:      0 CSB clocks
 106  *      [15:8]  DRAM Command Time:      0 CSB clocks
 107  *      [07:00] DRAM Precharge Time:    0 CSB clocks
 108  * TIME_CFG1
 109  *      [31:26] DRAM tRFC:
 110  *      [25:21] DRAM tWR1:
 111  *      [20:17] DRAM tWRT1:
 112  *      [16:11] DRAM tDRR:
 113  *      [10:05] DRAM tRC:
 114  *      [04:00] DRAM tRAS:
 115  * TIME_CFG2
 116  *      [31:28] DRAM tRCD:
 117  *      [27:23] DRAM tFAW:
 118  *      [22:19] DRAM tRTW1:
 119  *      [18:15] DRAM tCCD:
 120  *      [14:10] DRAM tRTP:
 121  *      [09:05] DRAM tRP:
 122  *      [04:00] DRAM tRPA
 123  */
 124 #ifdef CONFIG_MPC5121ADS_REV2
 125 #define CONFIG_SYS_MDDRC_SYS_CFG        0xE8604A00
 126 #define CONFIG_SYS_MDDRC_TIME_CFG1      0x54EC1168
 127 #define CONFIG_SYS_MDDRC_TIME_CFG2      0x35210864
 128 #else
 129 #define CONFIG_SYS_MDDRC_SYS_CFG        0xEA804A00
 130 #define CONFIG_SYS_MDDRC_TIME_CFG1      0x68EC1168
 131 #define CONFIG_SYS_MDDRC_TIME_CFG2      0x34310864
 132 #endif
 133 #define CONFIG_SYS_MDDRC_TIME_CFG0      0x06183D2E
 134
 135 #define CONFIG_SYS_MDDRC_SYS_CFG_ELPIDA         0xEA802B00
 136 #define CONFIG_SYS_MDDRC_TIME_CFG1_ELPIDA       0x690e1189
 137 #define CONFIG_SYS_MDDRC_TIME_CFG2_ELPIDA       0x35310864
 138
 139 #define CONFIG_SYS_DDRCMD_NOP           0x01380000
 140 #define CONFIG_SYS_DDRCMD_PCHG_ALL      0x01100400
 141 #define CONFIG_SYS_DDRCMD_EM2           0x01020000
 142 #define CONFIG_SYS_DDRCMD_EM3           0x01030000
 143 #define CONFIG_SYS_DDRCMD_EN_DLL        0x01010000
 144 #define CONFIG_SYS_DDRCMD_RFSH          0x01080000
 145
 146 #define DDRCMD_EMR_OCD(pr, ohm) ( \
 147         (1 << 24)          | /* MDDRC Command Request   */ \
 148         (1 << 16)          | /* MODE Reg BA[2:0]        */ \
 149         (0 << 12)          | /* Outputs 0=Enabled       */ \
 150         (0 << 11)          | /* RDQS                    */ \
 151         (1 << 10)          | /* DQS#                    */ \
 152         (pr <<  7)         | /* OCD prog 7=deflt,0=exit */ \
 153                     /* ODT Rtt[1:0] 0=0,1=75,2=150,3=50 */ \
 154         ((ohm & 0x2) <<  5)| /* Rtt1                    */ \
 155         (0 <<  3)          | /* additive posted CAS#    */ \
 156         ((ohm & 0x1) <<  2)| /* Rtt0                    */ \
 157         (0 <<  0)          | /* Output Drive Strength   */ \
 158         (0 <<  0))           /* DLL Enable 0=Normal     */
 159
 160 #define CONFIG_SYS_DDRCMD_OCD_DEFAULT   DDRCMD_EMR_OCD(7, 0)
 161 #define CONFIG_SYS_ELPIDA_OCD_EXIT      DDRCMD_EMR_OCD(0, 0)
 162
 163 #define DDRCMD_MODE_REG(cas, wr) ( \
 164         (1 << 24)    | /* MDDRC Command Request                 */ \
 165         (0 << 16)    | /* MODE Reg BA[2:0]                      */ \
 166         ((wr-1) << 9)| /* Write Recovery                        */ \
 167         (cas << 4)   | /* CAS                                   */ \
 168         (0 << 3)     | /* Burst Type:0=Sequential,1=Interleaved */ \
 169         (2 << 0))      /* 4 or 8 Burst Length:0x2=4 0x3=8       */
 170
 171 #define CONFIG_SYS_MICRON_INIT_DEV_OP   DDRCMD_MODE_REG(3, 3)
 172 #define CONFIG_SYS_ELPIDA_INIT_DEV_OP   DDRCMD_MODE_REG(4, 4)
 173 #define CONFIG_SYS_ELPIDA_RES_DLL       (DDRCMD_MODE_REG(4, 4) | (1 << 8))
 174
 175 /* DDR Priority Manager Configuration */
 176 #define CONFIG_SYS_MDDRCGRP_PM_CFG1     0x00077777
 177 #define CONFIG_SYS_MDDRCGRP_PM_CFG2     0x00000000
 178 #define CONFIG_SYS_MDDRCGRP_HIPRIO_CFG  0x00000001
 179 #define CONFIG_SYS_MDDRCGRP_LUT0_MU     0xFFEEDDCC
 180 #define CONFIG_SYS_MDDRCGRP_LUT0_ML     0xBBAAAAAA
 181 #define CONFIG_SYS_MDDRCGRP_LUT1_MU     0x66666666
 182 #define CONFIG_SYS_MDDRCGRP_LUT1_ML     0x55555555
 183 #define CONFIG_SYS_MDDRCGRP_LUT2_MU     0x44444444
 184 #define CONFIG_SYS_MDDRCGRP_LUT2_ML     0x44444444
 185 #define CONFIG_SYS_MDDRCGRP_LUT3_MU     0x55555555
 186 #define CONFIG_SYS_MDDRCGRP_LUT3_ML     0x55555558
 187 #define CONFIG_SYS_MDDRCGRP_LUT4_MU     0x11111111
 188 #define CONFIG_SYS_MDDRCGRP_LUT4_ML     0x11111122
 189 #define CONFIG_SYS_MDDRCGRP_LUT0_AU     0xaaaaaaaa
 190 #define CONFIG_SYS_MDDRCGRP_LUT0_AL     0xaaaaaaaa
 191 #define CONFIG_SYS_MDDRCGRP_LUT1_AU     0x66666666
 192 #define CONFIG_SYS_MDDRCGRP_LUT1_AL     0x66666666
 193 #define CONFIG_SYS_MDDRCGRP_LUT2_AU     0x11111111
 194 #define CONFIG_SYS_MDDRCGRP_LUT2_AL     0x11111111
 195 #define CONFIG_SYS_MDDRCGRP_LUT3_AU     0x11111111
 196 #define CONFIG_SYS_MDDRCGRP_LUT3_AL     0x11111111
 197 #define CONFIG_SYS_MDDRCGRP_LUT4_AU     0x11111111
 198 #define CONFIG_SYS_MDDRCGRP_LUT4_AL     0x11111111
 199
 200 /*
 201  * NOR FLASH on the Local Bus
 202  */
 203 #undef CONFIG_BKUP_FLASH
 204 #define CONFIG_SYS_FLASH_CFI                            /* use the Common Flash Interface */
 205 #define CONFIG_FLASH_CFI_DRIVER                 /* use the CFI driver */
 206 #ifdef CONFIG_BKUP_FLASH
 207 #define CONFIG_SYS_FLASH_BASE           0xFF800000      /* start of FLASH   */
 208 #define CONFIG_SYS_FLASH_SIZE           0x00800000      /* max flash size in bytes */
 209 #else
 210 #define CONFIG_SYS_FLASH_BASE           0xFC000000      /* start of FLASH   */
 211 #define CONFIG_SYS_FLASH_SIZE           0x04000000      /* max flash size in bytes */
 212 #endif
 213 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 214 #define CONFIG_SYS_MAX_FLASH_BANKS      1               /* number of banks */
 215 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE}
 216 #define CONFIG_SYS_MAX_FLASH_SECT       256             /* max sectors per device */
 217
 218 #undef CONFIG_SYS_FLASH_CHECKSUM
 219
 220 /*
 221  * NAND FLASH
 222  * drivers/mtd/nand/mpc5121_nfc.c (rev 2 silicon only)
 223  */
 224 #define CONFIG_CMD_NAND                                 /* enable NAND support */
 225 #define CONFIG_JFFS2_NAND                               /* with JFFS2 on it */
 226 #define CONFIG_NAND_MPC5121_NFC
 227 #define CONFIG_SYS_NAND_BASE            0x40000000
 228
 229 #define CONFIG_SYS_MAX_NAND_DEVICE      2
 230 #define CONFIG_SYS_NAND_SELECT_DEVICE   /* driver supports mutipl. chips */
 231
 232 /*
 233  * Configuration parameters for MPC5121 NAND driver
 234  */
 235 #define CONFIG_FSL_NFC_WIDTH 1
 236 #define CONFIG_FSL_NFC_WRITE_SIZE 2048
 237 #define CONFIG_FSL_NFC_SPARE_SIZE 64
 238 #define CONFIG_FSL_NFC_CHIPS CONFIG_SYS_MAX_NAND_DEVICE
 239
 240 /*
 241  * CPLD registers area is really only 32 bytes in size, but the smallest possible LP
 242  * window is 64KB
 243  */
 244 #define CONFIG_SYS_CPLD_BASE            0x82000000
 245 #define CONFIG_SYS_CPLD_SIZE            0x00010000      /* 64 KB */
 246 #define CONFIG_SYS_CS2_START            CONFIG_SYS_CPLD_BASE
 247 #define CONFIG_SYS_CS2_SIZE             CONFIG_SYS_CPLD_SIZE
 248
 249 #define CONFIG_SYS_SRAM_BASE            0x30000000
 250 #define CONFIG_SYS_SRAM_SIZE            0x00020000      /* 128 KB */
 251
 252 #define CONFIG_SYS_CS0_CFG              0x05059310      /* ALE active low, data size 4bytes */
 253 #define CONFIG_SYS_CS2_CFG              0x05059010      /* ALE active low, data size 1byte */
 254 #define CONFIG_SYS_CS_ALETIMING 0x00000005      /* Use alternative CS timing for CS0 and CS2 */
 255
 256 /* Use SRAM for initial stack */
 257 #define CONFIG_SYS_INIT_RAM_ADDR        CONFIG_SYS_SRAM_BASE            /* Initial RAM address */
 258 #define CONFIG_SYS_INIT_RAM_SIZE        CONFIG_SYS_SRAM_SIZE            /* Size of used area in RAM */
 259
 260 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 261 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 262
 263 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE            /* Start of monitor */
 264 #define CONFIG_SYS_MONITOR_LEN          (512 * 1024)            /* Reserve 512 kB for Mon */
 265 #ifdef  CONFIG_FSL_DIU_FB
 266 #define CONFIG_SYS_MALLOC_LEN           (6 * 1024 * 1024)       /* Reserved for malloc */
 267 #else
 268 #define CONFIG_SYS_MALLOC_LEN           (512 * 1024)
 269 #endif
 270
 271 /*
 272  * Serial Port
 273  */
 274 #define CONFIG_CONS_INDEX     1
 275
 276 /*
 277  * Serial console configuration
 278  */
 279 #define CONFIG_PSC_CONSOLE      3       /* console is on PSC3 */
 280 #define CONFIG_SYS_PSC3
 281 #if CONFIG_PSC_CONSOLE != 3
 282 #error CONFIG_PSC_CONSOLE must be 3
 283 #endif
 284 #define CONFIG_BAUDRATE         115200  /* ... at 115200 bps */
 285 #define CONFIG_SYS_BAUDRATE_TABLE  \
 286         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 287
 288 #define CONSOLE_FIFO_TX_SIZE    FIFOC_PSC3_TX_SIZE
 289 #define CONSOLE_FIFO_TX_ADDR    FIFOC_PSC3_TX_ADDR
 290 #define CONSOLE_FIFO_RX_SIZE    FIFOC_PSC3_RX_SIZE
 291 #define CONSOLE_FIFO_RX_ADDR    FIFOC_PSC3_RX_ADDR
 292
 293 #define CONFIG_CMDLINE_EDITING  1       /* add command line history     */
 294
 295 /*
 296  * Clocks in use
 297  */
 298 #define SCCR1_CLOCKS_EN (CLOCK_SCCR1_CFG_EN |                           \
 299                          CLOCK_SCCR1_DDR_EN |                           \
 300                          CLOCK_SCCR1_FEC_EN |                           \
 301                          CLOCK_SCCR1_LPC_EN |                           \
 302                          CLOCK_SCCR1_NFC_EN |                           \
 303                          CLOCK_SCCR1_PATA_EN |                          \
 304                          CLOCK_SCCR1_PCI_EN |                           \
 305                          CLOCK_SCCR1_PSC_EN(CONFIG_PSC_CONSOLE) |       \
 306                          CLOCK_SCCR1_PSCFIFO_EN |                       \
 307                          CLOCK_SCCR1_TPR_EN)
 308
 309 #define SCCR2_CLOCKS_EN (CLOCK_SCCR2_DIU_EN |           \
 310                          CLOCK_SCCR2_I2C_EN |           \
 311                          CLOCK_SCCR2_MEM_EN |           \
 312                          CLOCK_SCCR2_SPDIF_EN |         \
 313                          CLOCK_SCCR2_USB1_EN |          \
 314                          CLOCK_SCCR2_USB2_EN)
 315
 316 /*
 317  * PCI
 318  */
 319 #ifdef CONFIG_PCI
 320 #define CONFIG_PCI_INDIRECT_BRIDGE
 321
 322 /*
 323  * General PCI
 324  */
 325 #define CONFIG_SYS_PCI_MEM_BASE 0xA0000000
 326 #define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE
 327 #define CONFIG_SYS_PCI_MEM_SIZE 0x10000000      /* 256M */
 328 #define CONFIG_SYS_PCI_MMIO_BASE        (CONFIG_SYS_PCI_MEM_BASE + CONFIG_SYS_PCI_MEM_SIZE)
 329 #define CONFIG_SYS_PCI_MMIO_PHYS        CONFIG_SYS_PCI_MMIO_BASE
 330 #define CONFIG_SYS_PCI_MMIO_SIZE        0x10000000      /* 256M */
 331 #define CONFIG_SYS_PCI_IO_BASE          0x00000000
 332 #define CONFIG_SYS_PCI_IO_PHYS          0x84000000
 333 #define CONFIG_SYS_PCI_IO_SIZE          0x01000000      /* 16M */
 334
 335
 336 #define CONFIG_PCI_PNP                  /* do pci plug-and-play */
 337
 338 #define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
 339
 340 #endif
 341
 342 /* I2C */
 343 #define CONFIG_HARD_I2C                 /* I2C with hardware support */
 344 #define CONFIG_I2C_MULTI_BUS
 345 #define CONFIG_SYS_I2C_SPEED            100000  /* I2C speed and slave address */
 346 #define CONFIG_SYS_I2C_SLAVE            0x7F
 347 #if 0
 348 #define CONFIG_SYS_I2C_NOPROBES {{0,0x69}}      /* Don't probe these addrs */
 349 #endif
 350
 351 /*
 352  * IIM - IC Identification Module
 353  */
 354 #undef CONFIG_FSL_IIM
 355
 356 /*
 357  * EEPROM configuration
 358  */
 359 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          2       /* 16-bit EEPROM address */
 360 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x50    /* Atmel: AT24C32A-10TQ-2.7 */
 361 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10      /* 10ms of delay */
 362 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       5       /* 32-Byte Page Write Mode */
 363
 364 /*
 365  * Ethernet configuration
 366  */
 367 #define CONFIG_MPC512x_FEC      1
 368 #define CONFIG_PHY_ADDR         0x1
 369 #define CONFIG_MII              1       /* MII PHY management           */
 370 #define CONFIG_FEC_AN_TIMEOUT   1
 371 #define CONFIG_HAS_ETH0
 372
 373 /*
 374  * Configure on-board RTC
 375  */
 376 #define CONFIG_RTC_M41T62                       /* use M41T62 rtc via i2 */
 377 #define CONFIG_SYS_I2C_RTC_ADDR         0x68    /* at address 0x68              */
 378
 379 /*
 380  * USB  Support
 381  */
 382 #define CONFIG_CMD_USB
 383
 384 #if defined(CONFIG_CMD_USB)
 385 #define CONFIG_USB_EHCI                         /* Enable EHCI Support  */
 386 #define CONFIG_USB_EHCI_FSL                     /* On a FSL platform    */
 387 #define CONFIG_EHCI_MMIO_BIG_ENDIAN             /* With big-endian regs */
 388 #define CONFIG_EHCI_DESC_BIG_ENDIAN
 389 #define CONFIG_EHCI_IS_TDI
 390 #define CONFIG_USB_STORAGE
 391 #endif
 392
 393 /*
 394  * Environment
 395  */
 396 #define CONFIG_ENV_IS_IN_FLASH  1
 397 /* This has to be a multiple of the Flash sector size */
 398 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 399 #define CONFIG_ENV_SIZE         0x2000
 400 #ifdef CONFIG_BKUP_FLASH
 401 #define CONFIG_ENV_SECT_SIZE    0x20000 /* one sector (256K) for env */
 402 #else
 403 #define CONFIG_ENV_SECT_SIZE    0x40000 /* one sector (256K) for env */
 404 #endif
 405
 406 /* Address and size of Redundant Environment Sector     */
 407 #define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
 408 #define CONFIG_ENV_SIZE_REDUND  (CONFIG_ENV_SIZE)
 409
 410 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 411 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 412
 413 #define CONFIG_CMD_ASKENV
 414 #define CONFIG_CMD_DATE
 415 #define CONFIG_CMD_DHCP
 416 #define CONFIG_CMD_EEPROM
 417 #define CONFIG_CMD_EXT2
 418 #define CONFIG_CMD_I2C
 419 #define CONFIG_CMD_IDE
 420 #define CONFIG_CMD_JFFS2
 421 #define CONFIG_CMD_MII
 422 #define CONFIG_CMD_PING
 423 #define CONFIG_CMD_REGINFO
 424
 425 #undef CONFIG_CMD_FUSE
 426
 427 #if defined(CONFIG_PCI)
 428 #define CONFIG_CMD_PCI
 429 #endif
 430
 431 /*
 432  * Dynamic MTD partition support
 433  */
 434 #define CONFIG_CMD_MTDPARTS
 435 #define CONFIG_MTD_DEVICE               /* needed for mtdparts commands */
 436 #define CONFIG_FLASH_CFI_MTD
 437 #define MTDIDS_DEFAULT          "nor0=fc000000.flash,nand0=mpc5121.nand"
 438
 439 /*
 440  * NOR flash layout:
 441  *
 442  * FC000000 - FEABFFFF 42.75 MiB        User Data
 443  * FEAC0000 - FFABFFFF  16 MiB          Root File System
 444  * FFAC0000 - FFEBFFFF   4 MiB          Linux Kernel
 445  * FFEC0000 - FFEFFFFF 256 KiB          Device Tree
 446  * FFF00000 - FFFFFFFF   1 MiB          U-Boot (up to 512 KiB) and 2 x * env
 447  *
 448  * NAND flash layout: one big partition
 449  */
 450 #define MTDPARTS_DEFAULT        "mtdparts=fc000000.flash:43776k(user)," \
 451                                                 "16m(rootfs),"          \
 452                                                 "4m(kernel),"           \
 453                                                 "256k(dtb),"            \
 454                                                 "1m(u-boot);"           \
 455                                         "mpc5121.nand:-(data)"
 456
 457
 458 #if defined(CONFIG_CMD_IDE) || defined(CONFIG_CMD_EXT2) || defined(CONFIG_CMD_USB)
 459
 460 #define CONFIG_DOS_PARTITION
 461 #define CONFIG_MAC_PARTITION
 462 #define CONFIG_ISO_PARTITION
 463
 464 #define CONFIG_CMD_FAT
 465 #define CONFIG_SUPPORT_VFAT
 466
 467 #endif /* defined(CONFIG_CMD_IDE) */
 468
 469 /*
 470  * Watchdog timeout = CONFIG_SYS_WATCHDOG_VALUE * 65536 / IPS clock.
 471  * For example, when IPS is set to 66MHz and CONFIG_SYS_WATCHDOG_VALUE is set
 472  * to 0xFFFF, watchdog timeouts after about 64s. For details refer
 473  * to chapter 36 of the MPC5121e Reference Manual.
 474  */
 475 /* #define CONFIG_WATCHDOG */           /* enable watchdog */
 476 #define CONFIG_SYS_WATCHDOG_VALUE 0xFFFF
 477
 478  /*
 479  * Miscellaneous configurable options
 480  */
 481 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
 482 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 483
 484 #ifdef CONFIG_CMD_KGDB
 485         #define CONFIG_SYS_CBSIZE       1024    /* Console I/O Buffer Size */
 486 #else
 487         #define CONFIG_SYS_CBSIZE       256     /* Console I/O Buffer Size */
 488 #endif
 489
 490
 491 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buffer Size */
 492 #define CONFIG_SYS_MAXARGS      16              /* max number of command args */
 493 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size */
 494
 495 /*
 496  * For booting Linux, the board info and command line data
 497  * have to be in the first 256 MB of memory, since this is
 498  * the maximum mapped by the Linux kernel during initialization.
 499  */
 500 #define CONFIG_SYS_BOOTMAPSZ    (256 << 20)     /* Initial Memory map for Linux*/
 501
 502 /* Cache Configuration */
 503 #define CONFIG_SYS_DCACHE_SIZE          32768
 504 #define CONFIG_SYS_CACHELINE_SIZE       32
 505 #ifdef CONFIG_CMD_KGDB
 506 #define CONFIG_SYS_CACHELINE_SHIFT      5       /*log base 2 of the above value*/
 507 #endif
 508
 509 #define CONFIG_SYS_HID0_INIT    0x000000000
 510 #define CONFIG_SYS_HID0_FINAL   (HID0_ENABLE_MACHINE_CHECK | HID0_ICE)
 511 #define CONFIG_SYS_HID2 HID2_HBE
 512
 513 #define CONFIG_HIGH_BATS        1       /* High BATs supported */
 514
 515 #ifdef CONFIG_CMD_KGDB
 516 #define CONFIG_KGDB_BAUDRATE    230400  /* speed of kgdb serial port */
 517 #endif
 518
 519 /*
 520  * Environment Configuration
 521  */
 522 #define CONFIG_TIMESTAMP
 523
 524 #define CONFIG_HOSTNAME         mpc5121ads
 525 #define CONFIG_BOOTFILE         "mpc5121ads/uImage"
 526 #define CONFIG_ROOTPATH         "/opt/eldk/ppc_6xx"
 527
 528 #define CONFIG_LOADADDR         400000  /* default location for tftp and bootm */
 529
 530 #define CONFIG_BOOTDELAY        5       /* -1 disables auto-boot */
 531 #undef  CONFIG_BOOTARGS                 /* the boot command will set bootargs */
 532
 533 #define CONFIG_BAUDRATE         115200
 534
 535 #define CONFIG_PREBOOT  "echo;" \
 536         "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
 537         "echo"
 538
 539 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 540         "u-boot_addr_r=200000\0"                                        \
 541         "kernel_addr_r=600000\0"                                        \
 542         "fdt_addr_r=880000\0"                                           \
 543         "ramdisk_addr_r=900000\0"                                       \
 544         "u-boot_addr=FFF00000\0"                                        \
 545         "kernel_addr=FFAC0000\0"                                        \
 546         "fdt_addr=FFEC0000\0"                                           \
 547         "ramdisk_addr=FEAC0000\0"                                       \
 548         "ramdiskfile=mpc5121ads/uRamdisk\0"                             \
 549         "u-boot=mpc5121ads/u-boot.bin\0"                                \
 550         "bootfile=mpc5121ads/uImage\0"                                  \
 551         "fdtfile=mpc5121ads/mpc5121ads.dtb\0"                           \
 552         "rootpath=/opt/eldk/ppc_6xx\n"                                  \
 553         "netdev=eth0\0"                                                 \
 554         "consdev=ttyPSC0\0"                                             \
 555         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 556                 "nfsroot=${serverip}:${rootpath}\0"                     \
 557         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
 558         "addip=setenv bootargs ${bootargs} "                            \
 559                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
 560                 ":${hostname}:${netdev}:off panic=1\0"                  \
 561         "addtty=setenv bootargs ${bootargs} "                           \
 562                 "console=${consdev},${baudrate}\0"                      \
 563         "flash_nfs=run nfsargs addip addtty;"                           \
 564                 "bootm ${kernel_addr} - ${fdt_addr}\0"                  \
 565         "flash_self=run ramargs addip addtty;"                          \
 566                 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"    \
 567         "net_nfs=tftp ${kernel_addr_r} ${bootfile};"                    \
 568                 "tftp ${fdt_addr_r} ${fdtfile};"                        \
 569                 "run nfsargs addip addtty;"                             \
 570                 "bootm ${kernel_addr_r} - ${fdt_addr_r}\0"              \
 571         "net_self=tftp ${kernel_addr_r} ${bootfile};"                   \
 572                 "tftp ${ramdisk_addr_r} ${ramdiskfile};"                \
 573                 "tftp ${fdt_addr_r} ${fdtfile};"                        \
 574                 "run ramargs addip addtty;"                             \
 575                 "bootm ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr_r}\0"\
 576         "load=tftp ${u-boot_addr_r} ${u-boot}\0"                        \
 577         "update=protect off ${u-boot_addr} +${filesize};"               \
 578                 "era ${u-boot_addr} +${filesize};"                      \
 579                 "cp.b ${u-boot_addr_r} ${u-boot_addr} ${filesize}\0"    \
 580         "upd=run load update\0"                                         \
 581         ""
 582
 583 #define CONFIG_BOOTCOMMAND      "run flash_self"
 584
 585 #define CONFIG_OF_SUPPORT_OLD_DEVICE_TREES      1
 586
 587 #define OF_CPU                  "PowerPC,5121@0"
 588 #define OF_SOC_COMPAT           "fsl,mpc5121-immr"
 589 #define OF_TBCLK                (bd->bi_busfreq / 4)
 590 #define OF_STDOUT_PATH          "/soc@80000000/serial@11300"
 591
 592 /*-----------------------------------------------------------------------
 593  * IDE/ATA stuff
 594  *-----------------------------------------------------------------------
 595  */
 596
 597 #undef  CONFIG_IDE_8xx_PCCARD           /* Use IDE with PC Card Adapter */
 598 #undef  CONFIG_IDE_8xx_DIRECT           /* Direct IDE    not supported  */
 599 #undef  CONFIG_IDE_LED                  /* LED   for IDE not supported  */
 600
 601 #define CONFIG_IDE_RESET                /* reset for IDE supported      */
 602 #define CONFIG_IDE_PREINIT
 603
 604 #define CONFIG_SYS_IDE_MAXBUS           1       /* max. 1 IDE bus               */
 605 #define CONFIG_SYS_IDE_MAXDEVICE        2       /* max. 1 drive per IDE bus     */
 606
 607 #define CONFIG_SYS_ATA_IDE0_OFFSET      0x0000
 608 #define CONFIG_SYS_ATA_BASE_ADDR        get_pata_base()
 609
 610 /* Offset for data I/O                  RefMan MPC5121EE Table 28-10    */
 611 #define CONFIG_SYS_ATA_DATA_OFFSET      (0x00A0)
 612
 613 /* Offset for normal register accesses  */
 614 #define CONFIG_SYS_ATA_REG_OFFSET       (CONFIG_SYS_ATA_DATA_OFFSET)
 615
 616 /* Offset for alternate registers       RefMan MPC5121EE Table 28-23    */
 617 #define CONFIG_SYS_ATA_ALT_OFFSET       (0x00D8)
 618
 619 /* Interval between registers   */
 620 #define CONFIG_SYS_ATA_STRIDE           4
 621
 622 #define ATA_BASE_ADDR                   get_pata_base()
 623
 624 /*
 625  * Control register bit definitions
 626  */
 627 #define FSL_ATA_CTRL_FIFO_RST_B         0x80000000
 628 #define FSL_ATA_CTRL_ATA_RST_B          0x40000000
 629 #define FSL_ATA_CTRL_FIFO_TX_EN         0x20000000
 630 #define FSL_ATA_CTRL_FIFO_RCV_EN        0x10000000
 631 #define FSL_ATA_CTRL_DMA_PENDING        0x08000000
 632 #define FSL_ATA_CTRL_DMA_ULTRA          0x04000000
 633 #define FSL_ATA_CTRL_DMA_WRITE          0x02000000
 634 #define FSL_ATA_CTRL_IORDY_EN           0x01000000
 635
 636 #endif  /* __CONFIG_H */