include/configs/omap3_evm.h

   1 /*
   2  * Configuration settings for the TI OMAP3 EVM board.
   3  *
   4  * Copyright (C) 2006-2011 Texas Instruments Incorporated - http://www.ti.com/
   5  *
   6  * Author :
   7  *      Manikandan Pillai <mani.pillai@ti.com>
   8  * Derived from Beagle Board and 3430 SDP code by
   9  *      Richard Woodruff <r-woodruff2@ti.com>
  10  *      Syed Mohammed Khasim <khasim@ti.com>
  11  *
  12  * Manikandan Pillai <mani.pillai@ti.com>
  13  *
  14  * SPDX-License-Identifier:     GPL-2.0+
  15  */
  16
  17 #ifndef __OMAP3EVM_CONFIG_H
  18 #define __OMAP3EVM_CONFIG_H
  19
  20 #include <asm/arch/cpu.h>
  21 #include <asm/arch/omap.h>
  22
  23 /* ----------------------------------------------------------------------------
  24  * Supported U-Boot commands
  25  * ----------------------------------------------------------------------------
  26  */
  27
  28 #define CONFIG_CMD_JFFS2
  29
  30 #define CONFIG_CMD_NAND
  31
  32 /* ----------------------------------------------------------------------------
  33  * Supported U-Boot features
  34  * ----------------------------------------------------------------------------
  35  */
  36 #define CONFIG_SYS_LONGHELP
  37
  38 /* Allow to overwrite serial and ethaddr */
  39 #define CONFIG_ENV_OVERWRITE
  40
  41 /* Add auto-completion support */
  42 #define CONFIG_AUTO_COMPLETE
  43
  44 /* ----------------------------------------------------------------------------
  45  * Supported hardware
  46  * ----------------------------------------------------------------------------
  47  */
  48
  49 /* SPL */
  50 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION      1
  51 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
  52
  53 /* Partition tables */
  54
  55 /* USB
  56  *
  57  * Enable CONFIG_USB_MUSB_HCD for Host functionalities MSC, keyboard
  58  * Enable CONFIG_USB_MUSB_UDD for Device functionalities.
  59  */
  60 #define CONFIG_USB_OMAP3
  61 #define CONFIG_USB_MUSB_HCD
  62 /* #define CONFIG_USB_MUSB_UDC */
  63
  64 /* NAND SPL */
  65 #define CONFIG_SPL_NAND_SIMPLE
  66 #define CONFIG_SPL_NAND_BASE
  67 #define CONFIG_SPL_NAND_DRIVERS
  68 #define CONFIG_SPL_NAND_ECC
  69 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
  70 #define CONFIG_SYS_NAND_PAGE_COUNT      64
  71 #define CONFIG_SYS_NAND_PAGE_SIZE       2048
  72 #define CONFIG_SYS_NAND_OOBSIZE         64
  73 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128*1024)
  74 #define CONFIG_SYS_NAND_BAD_BLOCK_POS   0
  75 #define CONFIG_SYS_NAND_ECCPOS          {2, 3, 4, 5, 6, 7, 8, 9,\
  76                                                 10, 11, 12, 13}
  77 #define CONFIG_SYS_NAND_ECCSIZE         512
  78 #define CONFIG_SYS_NAND_ECCBYTES        3
  79 #define CONFIG_NAND_OMAP_ECCSCHEME      OMAP_ECC_HAM1_CODE_HW
  80 #define CONFIG_SYS_NAND_U_BOOT_START   CONFIG_SYS_TEXT_BASE
  81 #define CONFIG_SYS_NAND_U_BOOT_OFFS     0x80000
  82
  83 /*
  84  * High level configuration options
  85  */
  86 #define CONFIG_OMAP                     /* This is TI OMAP core */
  87 #define CONFIG_OMAP_GPIO
  88 /* Common ARM Erratas */
  89 #define CONFIG_ARM_ERRATA_454179
  90 #define CONFIG_ARM_ERRATA_430973
  91 #define CONFIG_ARM_ERRATA_621766
  92
  93 #define CONFIG_SDRC                     /* The chip has SDRC controller */
  94
  95 #define CONFIG_OMAP3_EVM                /* This is a OMAP3 EVM */
  96 #define CONFIG_TWL4030_POWER            /* with TWL4030 PMIC */
  97
  98 /*
  99  * Clock related definitions
 100  */
 101 #define V_OSCK                  26000000        /* Clock output from T2 */
 102 #define V_SCLK                  (V_OSCK >> 1)
 103
 104 /*
 105  * OMAP3 has 12 GP timers, they can be driven by the system clock
 106  * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
 107  * This rate is divided by a local divisor.
 108  */
 109 #define CONFIG_SYS_TIMERBASE            OMAP34XX_GPT2
 110 #define CONFIG_SYS_PTV                  2       /* Divisor: 2^(PTV+1) => 8 */
 111
 112 /* Size of environment - 128KB */
 113 #define CONFIG_ENV_SIZE                 (128 << 10)
 114
 115 /* Size of malloc pool */
 116 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + (128 << 10))
 117
 118 /*
 119  * Physical Memory Map
 120  * Note 1: CS1 may or may not be populated
 121  * Note 2: SDRAM size is expected to be at least 32MB
 122  */
 123 #define CONFIG_NR_DRAM_BANKS            2
 124 #define PHYS_SDRAM_1                    OMAP34XX_SDRC_CS0
 125 #define PHYS_SDRAM_2                    OMAP34XX_SDRC_CS1
 126
 127 /* Limits for memtest */
 128 #define CONFIG_SYS_MEMTEST_START        (OMAP34XX_SDRC_CS0)
 129 #define CONFIG_SYS_MEMTEST_END          (OMAP34XX_SDRC_CS0 + \
 130                                                 0x01F00000) /* 31MB */
 131
 132 /* Default load address */
 133 #define CONFIG_SYS_LOAD_ADDR            (OMAP34XX_SDRC_CS0)
 134
 135 /* -----------------------------------------------------------------------------
 136  * Hardware drivers
 137  * -----------------------------------------------------------------------------
 138  */
 139
 140 /*
 141  * NS16550 Configuration
 142  */
 143 #define V_NS16550_CLK                   48000000        /* 48MHz (APLL96/2) */
 144
 145 #define CONFIG_SYS_NS16550_SERIAL
 146 #define CONFIG_SYS_NS16550_REG_SIZE     (-4)
 147 #define CONFIG_SYS_NS16550_CLK          V_NS16550_CLK
 148
 149 /*
 150  * select serial console configuration
 151  */
 152 #define CONFIG_CONS_INDEX               1
 153 #define CONFIG_SERIAL1                  1       /* UART1 on OMAP3 EVM */
 154 #define CONFIG_SYS_NS16550_COM1         OMAP34XX_UART1
 155 #define CONFIG_BAUDRATE                 115200
 156 #define CONFIG_SYS_BAUDRATE_TABLE       {4800, 9600, 19200, 38400, 57600,\
 157                                         115200}
 158
 159 /*
 160  * I2C
 161  */
 162 #define CONFIG_SYS_I2C
 163 #define CONFIG_SYS_OMAP24_I2C_SPEED     100000
 164 #define CONFIG_SYS_OMAP24_I2C_SLAVE     1
 165 #define CONFIG_SYS_I2C_OMAP34XX
 166
 167 /*
 168  * PISMO support
 169  */
 170 /* Monitor at start of flash - Reserve 2 sectors */
 171 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_FLASH_BASE
 172
 173 #define CONFIG_SYS_MONITOR_LEN          (256 << 10)
 174
 175 /* Start location & size of environment */
 176 #define ONENAND_ENV_OFFSET              0x260000
 177 #define SMNAND_ENV_OFFSET               0x260000
 178
 179 #define CONFIG_SYS_ENV_SECT_SIZE        (128 << 10)     /* 128 KiB */
 180
 181 /*
 182  * NAND
 183  */
 184 /* Physical address to access NAND */
 185 #define CONFIG_SYS_NAND_ADDR            NAND_BASE
 186
 187 /* Physical address to access NAND at CS0 */
 188 #define CONFIG_SYS_NAND_BASE            NAND_BASE
 189
 190 /* Max number of NAND devices */
 191 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 192 #define CONFIG_SYS_NAND_BUSWIDTH_16BIT
 193 /* Timeout values (in ticks) */
 194 #define CONFIG_SYS_FLASH_ERASE_TOUT     (100 * CONFIG_SYS_HZ)
 195 #define CONFIG_SYS_FLASH_WRITE_TOUT     (100 * CONFIG_SYS_HZ)
 196
 197 /* Flash banks JFFS2 should use */
 198 #define CONFIG_SYS_MAX_MTD_BANKS        (CONFIG_SYS_MAX_FLASH_BANKS + \
 199                                                 CONFIG_SYS_MAX_NAND_DEVICE)
 200
 201 #define CONFIG_SYS_JFFS2_MEM_NAND
 202 #define CONFIG_SYS_JFFS2_FIRST_BANK     CONFIG_SYS_MAX_FLASH_BANKS
 203 #define CONFIG_SYS_JFFS2_NUM_BANKS      1
 204
 205 #define CONFIG_JFFS2_NAND
 206 /* nand device jffs2 lives on */
 207 #define CONFIG_JFFS2_DEV                "nand0"
 208 /* Start of jffs2 partition */
 209 #define CONFIG_JFFS2_PART_OFFSET        0x680000
 210 /* Size of jffs2 partition */
 211 #define CONFIG_JFFS2_PART_SIZE          0xf980000
 212
 213 /*
 214  * USB
 215  */
 216 #ifdef CONFIG_USB_OMAP3
 217
 218 #ifdef CONFIG_USB_MUSB_HCD
 219
 220 #ifdef CONFIG_USB_KEYBOARD
 221 #define CONFIG_SYS_USB_EVENT_POLL
 222 #define CONFIG_PREBOOT                  "usb start"
 223 #endif /* CONFIG_USB_KEYBOARD */
 224
 225 #endif /* CONFIG_USB_MUSB_HCD */
 226
 227 #ifdef CONFIG_USB_MUSB_UDC
 228 /* USB device configuration */
 229 #define CONFIG_USB_DEVICE
 230 #define CONFIG_USB_TTY
 231
 232 /* Change these to suit your needs */
 233 #define CONFIG_USBD_VENDORID            0x0451
 234 #define CONFIG_USBD_PRODUCTID           0x5678
 235 #define CONFIG_USBD_MANUFACTURER        "Texas Instruments"
 236 #define CONFIG_USBD_PRODUCT_NAME        "EVM"
 237 #endif /* CONFIG_USB_MUSB_UDC */
 238
 239 #endif /* CONFIG_USB_OMAP3 */
 240
 241 /* ----------------------------------------------------------------------------
 242  * U-Boot features
 243  * ----------------------------------------------------------------------------
 244  */
 245 #define CONFIG_SYS_MAXARGS              16      /* max args for a command */
 246
 247 #define CONFIG_MISC_INIT_R
 248
 249 #define CONFIG_CMDLINE_TAG                      /* enable passing of ATAGs */
 250 #define CONFIG_SETUP_MEMORY_TAGS
 251 #define CONFIG_INITRD_TAG
 252 #define CONFIG_REVISION_TAG
 253
 254 /* Size of Console IO buffer */
 255 #define CONFIG_SYS_CBSIZE               512
 256
 257 /* Size of print buffer */
 258 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE + \
 259                                                 sizeof(CONFIG_SYS_PROMPT) + 16)
 260
 261 /* Size of bootarg buffer */
 262 #define CONFIG_SYS_BARGSIZE             (CONFIG_SYS_CBSIZE)
 263
 264 #define CONFIG_BOOTFILE                 "uImage"
 265
 266 /*
 267  * NAND / OneNAND
 268  */
 269 #if defined(CONFIG_CMD_NAND)
 270 #define CONFIG_SYS_FLASH_BASE           NAND_BASE
 271
 272 #define CONFIG_NAND_OMAP_GPMC
 273 #define CONFIG_ENV_OFFSET               SMNAND_ENV_OFFSET
 274 #elif defined(CONFIG_CMD_ONENAND)
 275 #define CONFIG_SYS_FLASH_BASE           ONENAND_MAP
 276 #define CONFIG_SYS_ONENAND_BASE         ONENAND_MAP
 277 #endif
 278
 279 #if !defined(CONFIG_ENV_IS_NOWHERE)
 280 #if defined(CONFIG_CMD_NAND)
 281 #define CONFIG_ENV_IS_IN_NAND
 282 #elif defined(CONFIG_CMD_ONENAND)
 283 #define CONFIG_ENV_IS_IN_ONENAND
 284 #define CONFIG_ENV_OFFSET               ONENAND_ENV_OFFSET
 285 #endif
 286 #endif /* CONFIG_ENV_IS_NOWHERE */
 287
 288 #define CONFIG_ENV_ADDR                 CONFIG_ENV_OFFSET
 289
 290 #if defined(CONFIG_CMD_NET)
 291
 292 /* Ethernet (SMSC9115 from SMSC9118 family) */
 293 #define CONFIG_SMC911X
 294 #define CONFIG_SMC911X_32_BIT
 295 #define CONFIG_SMC911X_BASE             0x2C000000
 296
 297 /* BOOTP fields */
 298 #define CONFIG_BOOTP_SUBNETMASK         0x00000001
 299 #define CONFIG_BOOTP_GATEWAY            0x00000002
 300 #define CONFIG_BOOTP_HOSTNAME           0x00000004
 301 #define CONFIG_BOOTP_BOOTPATH           0x00000010
 302
 303 #endif /* CONFIG_CMD_NET */
 304
 305 /* Support for relocation */
 306 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM_1
 307 #define CONFIG_SYS_INIT_RAM_ADDR        0x4020f800
 308 #define CONFIG_SYS_INIT_RAM_SIZE        0x800
 309 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_INIT_RAM_ADDR + \
 310                                          CONFIG_SYS_INIT_RAM_SIZE - \
 311                                          GENERATED_GBL_DATA_SIZE)
 312
 313 /* -----------------------------------------------------------------------------
 314  * Board specific
 315  * -----------------------------------------------------------------------------
 316  */
 317
 318 /* Uncomment to define the board revision statically */
 319 /* #define CONFIG_STATIC_BOARD_REV      OMAP3EVM_BOARD_GEN_2 */
 320
 321 /* Defines for SPL */
 322 #define CONFIG_SPL_FRAMEWORK
 323 #define CONFIG_SPL_TEXT_BASE            0x40200800
 324 #define CONFIG_SPL_MAX_SIZE             (SRAM_SCRATCH_SPACE_ADDR - \
 325                                          CONFIG_SPL_TEXT_BASE)
 326
 327 #define CONFIG_SPL_BSS_START_ADDR       0x80000000
 328 #define CONFIG_SPL_BSS_MAX_SIZE         0x80000         /* 512 KB */
 329
 330 #define CONFIG_SPL_BOARD_INIT
 331 #define CONFIG_SPL_OMAP3_ID_NAND
 332 #define CONFIG_SPL_LDSCRIPT             "arch/arm/mach-omap2/u-boot-spl.lds"
 333
 334 /*
 335  * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
 336  * 64 bytes before this address should be set aside for u-boot.img's
 337  * header. That is 0x800FFFC0--0x80100000 should not be used for any
 338  * other needs.
 339  */
 340 #define CONFIG_SYS_TEXT_BASE            0x80100000
 341 #define CONFIG_SYS_SPL_MALLOC_START     0x80208000
 342 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x100000
 343
 344 /* -----------------------------------------------------------------------------
 345  * Default environment
 346  * -----------------------------------------------------------------------------
 347  */
 348
 349 #define CONFIG_EXTRA_ENV_SETTINGS \
 350         "loadaddr=0x82000000\0" \
 351         "usbtty=cdc_acm\0" \
 352         "mmcdev=0\0" \
 353         "console=ttyO0,115200n8\0" \
 354         "mmcargs=setenv bootargs console=${console} " \
 355                 "root=/dev/mmcblk0p2 rw " \
 356                 "rootfstype=ext3 rootwait\0" \
 357         "nandargs=setenv bootargs console=${console} " \
 358                 "root=/dev/mtdblock4 rw " \
 359                 "rootfstype=jffs2\0" \
 360         "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
 361         "bootscript=echo Running bootscript from mmc ...; " \
 362                 "source ${loadaddr}\0" \
 363         "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
 364         "mmcboot=echo Booting from mmc ...; " \
 365                 "run mmcargs; " \
 366                 "bootm ${loadaddr}\0" \
 367         "nandboot=echo Booting from nand ...; " \
 368                 "run nandargs; " \
 369                 "onenand read ${loadaddr} 280000 400000; " \
 370                 "bootm ${loadaddr}\0" \
 371
 372 #define CONFIG_BOOTCOMMAND \
 373         "mmc dev ${mmcdev}; if mmc rescan; then " \
 374                 "if run loadbootscript; then " \
 375                         "run bootscript; " \
 376                 "else " \
 377                         "if run loaduimage; then " \
 378                                 "run mmcboot; " \
 379                         "else run nandboot; " \
 380                         "fi; " \
 381                 "fi; " \
 382         "else run nandboot; fi"
 383
 384 #endif /* __OMAP3EVM_CONFIG_H */