include/configs/p1_twr.h

   1 /*
   2  * Copyright 2013 Freescale Semiconductor, Inc.
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 /*
   8  * QorIQ P1 Tower boards configuration file
   9  */
  10 #ifndef __CONFIG_H
  11 #define __CONFIG_H
  12
  13 #define CONFIG_DISPLAY_BOARDINFO
  14 #if defined(CONFIG_TWR_P1025)
  15 #define CONFIG_BOARDNAME "TWR-P1025"
  16 #define CONFIG_P1025
  17 #define CONFIG_PHY_ATHEROS
  18 #define CONFIG_QE
  19 #define CONFIG_SYS_LBC_LBCR     0x00080000      /* Conversion of LBC addr */
  20 #define CONFIG_SYS_LBC_LCRR     0x80000002      /* LB clock ratio reg */
  21 #endif
  22
  23 #ifdef CONFIG_SDCARD
  24 #define CONFIG_RAMBOOT_SDCARD
  25 #define CONFIG_SYS_RAMBOOT
  26 #define CONFIG_SYS_EXTRA_ENV_RELOC
  27 #define CONFIG_SYS_TEXT_BASE            0x11000000
  28 #define CONFIG_RESET_VECTOR_ADDRESS     0x110bfffc
  29 #endif
  30
  31 #ifndef CONFIG_SYS_TEXT_BASE
  32 #define CONFIG_SYS_TEXT_BASE            0xeff40000
  33 #endif
  34
  35 #ifndef CONFIG_RESET_VECTOR_ADDRESS
  36 #define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
  37 #endif
  38
  39 #ifndef CONFIG_SYS_MONITOR_BASE
  40 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
  41 #endif
  42
  43 /* High Level Configuration Options */
  44 #define CONFIG_BOOKE
  45 #define CONFIG_E500
  46
  47 #define CONFIG_MP
  48
  49 #define CONFIG_FSL_ELBC
  50 #define CONFIG_PCI
  51 #define CONFIG_PCIE1    /* PCIE controler 1 (slot 1) */
  52 #define CONFIG_PCIE2    /* PCIE controler 2 (slot 2) */
  53 #define CONFIG_FSL_PCI_INIT     /* Use common FSL init code */
  54 #define CONFIG_PCI_INDIRECT_BRIDGE      /* indirect PCI bridge support */
  55 #define CONFIG_FSL_PCIE_RESET   /* need PCIe reset errata */
  56 #define CONFIG_SYS_PCI_64BIT    /* enable 64-bit PCI resources */
  57
  58 #define CONFIG_FSL_LAW
  59 #define CONFIG_TSEC_ENET        /* tsec ethernet support */
  60 #define CONFIG_ENV_OVERWRITE
  61
  62 #define CONFIG_CMD_SATA
  63 #define CONFIG_SATA_SIL3114
  64 #define CONFIG_SYS_SATA_MAX_DEVICE      2
  65 #define CONFIG_LIBATA
  66 #define CONFIG_LBA48
  67
  68 #ifndef __ASSEMBLY__
  69 extern unsigned long get_board_sys_clk(unsigned long dummy);
  70 #endif
  71 #define CONFIG_SYS_CLK_FREQ     get_board_sys_clk(0) /*sysclk for TWR-P1025 */
  72
  73 #define CONFIG_DDR_CLK_FREQ     66666666
  74
  75 #define CONFIG_HWCONFIG
  76 /*
  77  * These can be toggled for performance analysis, otherwise use default.
  78  */
  79 #define CONFIG_L2_CACHE
  80 #define CONFIG_BTB
  81
  82 #define CONFIG_BOARD_EARLY_INIT_F       /* Call board_pre_init */
  83
  84 #define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest works on */
  85 #define CONFIG_SYS_MEMTEST_END          0x1fffffff
  86 #define CONFIG_PANIC_HANG       /* do not reset board on panic */
  87
  88 #define CONFIG_SYS_CCSRBAR              0xffe00000
  89 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR
  90
  91 /* DDR Setup */
  92 #define CONFIG_SYS_FSL_DDR3
  93
  94 #define CONFIG_SYS_SDRAM_SIZE_LAW       LAW_SIZE_512M
  95 #define CONFIG_CHIP_SELECTS_PER_CTRL    1
  96
  97 #define CONFIG_SYS_SDRAM_SIZE           (1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19))
  98 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
  99 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 100
 101 #define CONFIG_NUM_DDR_CONTROLLERS      1
 102 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
 103
 104 /* Default settings for DDR3 */
 105 #define CONFIG_SYS_DDR_CS0_BNDS         0x0000001f
 106 #define CONFIG_SYS_DDR_CS0_CONFIG       0x80014202
 107 #define CONFIG_SYS_DDR_CS0_CONFIG_2     0x00000000
 108 #define CONFIG_SYS_DDR_CS1_BNDS         0x00000000
 109 #define CONFIG_SYS_DDR_CS1_CONFIG       0x00000000
 110 #define CONFIG_SYS_DDR_CS1_CONFIG_2     0x00000000
 111
 112 #define CONFIG_SYS_DDR_DATA_INIT        0xdeadbeef
 113 #define CONFIG_SYS_DDR_INIT_ADDR        0x00000000
 114 #define CONFIG_SYS_DDR_INIT_EXT_ADDR    0x00000000
 115 #define CONFIG_SYS_DDR_MODE_CONTROL     0x00000000
 116
 117 #define CONFIG_SYS_DDR_ZQ_CONTROL       0x89080600
 118 #define CONFIG_SYS_DDR_WRLVL_CONTROL    0x8655a608
 119 #define CONFIG_SYS_DDR_SR_CNTR          0x00000000
 120 #define CONFIG_SYS_DDR_RCW_1            0x00000000
 121 #define CONFIG_SYS_DDR_RCW_2            0x00000000
 122 #define CONFIG_SYS_DDR_CONTROL          0xc70c0000      /* Type = DDR3  */
 123 #define CONFIG_SYS_DDR_CONTROL_2        0x04401050
 124 #define CONFIG_SYS_DDR_TIMING_4         0x00220001
 125 #define CONFIG_SYS_DDR_TIMING_5         0x03402400
 126
 127 #define CONFIG_SYS_DDR_TIMING_3         0x00020000
 128 #define CONFIG_SYS_DDR_TIMING_0         0x00220004
 129 #define CONFIG_SYS_DDR_TIMING_1         0x5c5b6544
 130 #define CONFIG_SYS_DDR_TIMING_2         0x0fa880de
 131 #define CONFIG_SYS_DDR_CLK_CTRL         0x03000000
 132 #define CONFIG_SYS_DDR_MODE_1           0x80461320
 133 #define CONFIG_SYS_DDR_MODE_2           0x00008000
 134 #define CONFIG_SYS_DDR_INTERVAL         0x09480000
 135
 136 /*
 137  * Memory map
 138  *
 139  * 0x0000_0000 0x1fff_ffff      DDR             Up to 512MB cacheable
 140  * 0x8000_0000 0xdfff_ffff      PCI Express Mem 1.5G non-cacheable(PCIe * 3)
 141  * 0xffc0_0000 0xffc3_ffff      PCI IO range    256k non-cacheable
 142  *
 143  * Localbus
 144  * 0xe000_0000 0xe002_0000      SSD1289         128K non-cacheable
 145  * 0xec00_0000 0xefff_ffff      FLASH           Up to 64M non-cacheable
 146  *
 147  * 0xff90_0000 0xff97_ffff      L2 SRAM         Up to 512K cacheable
 148  * 0xffd0_0000 0xffd0_3fff      init ram        16K Cacheable
 149  * 0xffe0_0000 0xffef_ffff      CCSR            1M non-cacheable
 150  */
 151
 152 /*
 153  * Local Bus Definitions
 154  */
 155 #define CONFIG_SYS_MAX_FLASH_SECT       512     /* 64M */
 156 #define CONFIG_SYS_FLASH_BASE           0xec000000
 157
 158 #define CONFIG_SYS_FLASH_BASE_PHYS      CONFIG_SYS_FLASH_BASE
 159
 160 #define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS)) \
 161         | BR_PS_16 | BR_V)
 162
 163 #define CONFIG_FLASH_OR_PRELIM  0xfc0000b1
 164
 165 #define CONFIG_SYS_SSD_BASE     0xe0000000
 166 #define CONFIG_SYS_SSD_BASE_PHYS        CONFIG_SYS_SSD_BASE
 167 #define CONFIG_SSD_BR_PRELIM    (BR_PHYS_ADDR(CONFIG_SYS_SSD_BASE_PHYS) | \
 168                                         BR_PS_16 | BR_V)
 169 #define CONFIG_SSD_OR_PRELIM    (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \
 170                                  OR_GPCM_ACS_DIV2 | OR_GPCM_SCY | \
 171                                  OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD)
 172
 173 #define CONFIG_SYS_BR2_PRELIM CONFIG_SSD_BR_PRELIM
 174 #define CONFIG_SYS_OR2_PRELIM CONFIG_SSD_OR_PRELIM
 175
 176 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS}
 177 #define CONFIG_SYS_FLASH_QUIET_TEST
 178 #define CONFIG_FLASH_SHOW_PROGRESS      45      /* count down from 45/5: 9..1 */
 179
 180 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 181
 182 #undef CONFIG_SYS_FLASH_CHECKSUM
 183 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 184 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 185
 186 #define CONFIG_FLASH_CFI_DRIVER
 187 #define CONFIG_SYS_FLASH_CFI
 188 #define CONFIG_SYS_FLASH_EMPTY_INFO
 189 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 190
 191 #define CONFIG_BOARD_EARLY_INIT_R       /* call board_early_init_r function */
 192
 193 #define CONFIG_SYS_INIT_RAM_LOCK
 194 #define CONFIG_SYS_INIT_RAM_ADDR        0xffd00000
 195 /* Initial L1 address */
 196 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS   CONFIG_SYS_INIT_RAM_ADDR
 197 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
 198 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
 199 /* Size of used area in RAM */
 200 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000
 201
 202 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 203                                         GENERATED_GBL_DATA_SIZE)
 204 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 205
 206 #define CONFIG_SYS_MONITOR_LEN  (768 * 1024)
 207 #define CONFIG_SYS_MALLOC_LEN   (1024 * 1024)/* Reserved for malloc */
 208
 209 #define CONFIG_SYS_BR0_PRELIM   CONFIG_FLASH_BR_PRELIM  /* NOR Base Address */
 210 #define CONFIG_SYS_OR0_PRELIM   CONFIG_FLASH_OR_PRELIM  /* NOR Options */
 211
 212 /* Serial Port
 213  * open - index 2
 214  * shorted - index 1
 215  */
 216 #define CONFIG_CONS_INDEX               1
 217 #undef CONFIG_SERIAL_SOFTWARE_FIFO
 218 #define CONFIG_SYS_NS16550_SERIAL
 219 #define CONFIG_SYS_NS16550_REG_SIZE     1
 220 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 221
 222 #define CONFIG_SYS_BAUDRATE_TABLE       \
 223         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 224
 225 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
 226 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
 227
 228 /* Use the HUSH parser */
 229 #define CONFIG_SYS_HUSH_PARSER
 230 #ifdef CONFIG_SYS_HUSH_PARSER
 231 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
 232 #endif
 233
 234 /*
 235  * Pass open firmware flat tree
 236  */
 237 #define CONFIG_OF_BOARD_SETUP
 238 #define CONFIG_OF_STDOUT_VIA_ALIAS
 239
 240 /* new uImage format support */
 241 #define CONFIG_FIT
 242 #define CONFIG_FIT_VERBOSE      /* enable fit_format_{error,warning}() */
 243
 244 /* I2C */
 245 #define CONFIG_SYS_I2C
 246 #define CONFIG_SYS_I2C_FSL                      /* Use FSL common I2C driver */
 247 #define CONFIG_SYS_FSL_I2C_SPEED        400000  /* I2C spd and slave address */
 248 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 249 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 250 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x52
 251
 252 /*
 253  * I2C2 EEPROM
 254  */
 255 #define CONFIG_SYS_FSL_I2C2_SPEED       400000  /* I2C spd and slave address */
 256 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 257 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 258
 259 #define CONFIG_SYS_I2C_PCA9555_ADDR     0x23
 260
 261 /* enable read and write access to EEPROM */
 262 #define CONFIG_CMD_EEPROM
 263 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 264 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
 265 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
 266
 267 /*
 268  * eSPI - Enhanced SPI
 269  */
 270 #define CONFIG_HARD_SPI
 271
 272 #if defined(CONFIG_PCI)
 273 /*
 274  * General PCI
 275  * Memory space is mapped 1-1, but I/O space must start from 0.
 276  */
 277
 278 /* controller 2, direct to uli, tgtid 2, Base address 9000 */
 279 #define CONFIG_SYS_PCIE2_NAME           "TWR-ELEV PCIe SLOT"
 280 #define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
 281 #define CONFIG_SYS_PCIE2_MEM_BUS        0xa0000000
 282 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xa0000000
 283 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x20000000      /* 512M */
 284 #define CONFIG_SYS_PCIE2_IO_VIRT        0xffc10000
 285 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 286 #define CONFIG_SYS_PCIE2_IO_PHYS        0xffc10000
 287 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00010000      /* 64k */
 288
 289 /* controller 1, tgtid 1, Base address a000 */
 290 #define CONFIG_SYS_PCIE1_NAME           "mini PCIe SLOT"
 291 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 292 #define CONFIG_SYS_PCIE1_MEM_BUS        0x80000000
 293 #define CONFIG_SYS_PCIE1_MEM_PHYS       0x80000000
 294 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 295 #define CONFIG_SYS_PCIE1_IO_VIRT        0xffc00000
 296 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 297 #define CONFIG_SYS_PCIE1_IO_PHYS        0xffc00000
 298 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */
 299
 300 #define CONFIG_PCI_PNP  /* do pci plug-and-play */
 301 #define CONFIG_CMD_PCI
 302
 303 #define CONFIG_PCI_SCAN_SHOW    /* show pci devices on startup */
 304 #define CONFIG_DOS_PARTITION
 305 #endif /* CONFIG_PCI */
 306
 307 #if defined(CONFIG_TSEC_ENET)
 308
 309 #define CONFIG_MII              /* MII PHY management */
 310 #define CONFIG_TSEC1
 311 #define CONFIG_TSEC1_NAME       "eTSEC1"
 312 #undef CONFIG_TSEC2
 313 #undef CONFIG_TSEC2_NAME
 314 #define CONFIG_TSEC3
 315 #define CONFIG_TSEC3_NAME       "eTSEC3"
 316
 317 #define TSEC1_PHY_ADDR  2
 318 #define TSEC2_PHY_ADDR  0
 319 #define TSEC3_PHY_ADDR  1
 320
 321 #define TSEC1_FLAGS     (TSEC_GIGABIT | TSEC_REDUCED)
 322 #define TSEC2_FLAGS     (TSEC_GIGABIT | TSEC_REDUCED)
 323 #define TSEC3_FLAGS     (TSEC_GIGABIT | TSEC_REDUCED)
 324
 325 #define TSEC1_PHYIDX    0
 326 #define TSEC2_PHYIDX    0
 327 #define TSEC3_PHYIDX    0
 328
 329 #define CONFIG_ETHPRIME "eTSEC1"
 330
 331 #define CONFIG_PHY_GIGE 1       /* Include GbE speed/duplex detection */
 332
 333 #define CONFIG_HAS_ETH0
 334 #define CONFIG_HAS_ETH1
 335 #undef CONFIG_HAS_ETH2
 336 #endif /* CONFIG_TSEC_ENET */
 337
 338 #ifdef CONFIG_QE
 339 /* QE microcode/firmware address */
 340 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
 341 #define CONFIG_SYS_QE_FW_ADDR   0xefec0000
 342 #define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
 343 #endif /* CONFIG_QE */
 344
 345 #ifdef CONFIG_TWR_P1025
 346 /*
 347  * QE UEC ethernet configuration
 348  */
 349 #define CONFIG_MIIM_ADDRESS     (CONFIG_SYS_CCSRBAR + 0x82120)
 350
 351 #undef CONFIG_UEC_ETH
 352 #define CONFIG_PHY_MODE_NEED_CHANGE
 353
 354 #define CONFIG_UEC_ETH1 /* ETH1 */
 355 #define CONFIG_HAS_ETH0
 356
 357 #ifdef CONFIG_UEC_ETH1
 358 #define CONFIG_SYS_UEC1_UCC_NUM 0       /* UCC1 */
 359 #define CONFIG_SYS_UEC1_RX_CLK  QE_CLK12 /* CLK12 for MII */
 360 #define CONFIG_SYS_UEC1_TX_CLK  QE_CLK9 /* CLK9 for MII */
 361 #define CONFIG_SYS_UEC1_ETH_TYPE        FAST_ETH
 362 #define CONFIG_SYS_UEC1_PHY_ADDR        0x18    /* 0x18 for MII */
 363 #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_MII
 364 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
 365 #endif /* CONFIG_UEC_ETH1 */
 366
 367 #define CONFIG_UEC_ETH5 /* ETH5 */
 368 #define CONFIG_HAS_ETH1
 369
 370 #ifdef CONFIG_UEC_ETH5
 371 #define CONFIG_SYS_UEC5_UCC_NUM 4       /* UCC5 */
 372 #define CONFIG_SYS_UEC5_RX_CLK  QE_CLK_NONE
 373 #define CONFIG_SYS_UEC5_TX_CLK  QE_CLK13 /* CLK 13 for RMII */
 374 #define CONFIG_SYS_UEC5_ETH_TYPE        FAST_ETH
 375 #define CONFIG_SYS_UEC5_PHY_ADDR        0x19    /* 0x19 for RMII */
 376 #define CONFIG_SYS_UEC5_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
 377 #define CONFIG_SYS_UEC5_INTERFACE_SPEED 100
 378 #endif /* CONFIG_UEC_ETH5 */
 379 #endif /* CONFIG_TWR-P1025 */
 380
 381 /*
 382  * Dynamic MTD Partition support with mtdparts
 383  */
 384 #define CONFIG_MTD_DEVICE
 385 #define CONFIG_MTD_PARTITIONS
 386 #define CONFIG_CMD_MTDPARTS
 387 #define CONFIG_FLASH_CFI_MTD
 388 #define MTDIDS_DEFAULT "nor0=ec000000.nor"
 389 #define MTDPARTS_DEFAULT "mtdparts=ec000000.nor:256k(vsc7385-firmware)," \
 390                         "256k(dtb),5632k(kernel),57856k(fs)," \
 391                         "256k(qe-ucode-firmware),1280k(u-boot)"
 392
 393 /*
 394  * Environment
 395  */
 396 #ifdef CONFIG_SYS_RAMBOOT
 397 #ifdef CONFIG_RAMBOOT_SDCARD
 398 #define CONFIG_ENV_IS_IN_MMC
 399 #define CONFIG_ENV_SIZE         0x2000
 400 #define CONFIG_SYS_MMC_ENV_DEV  0
 401 #else
 402 #define CONFIG_ENV_IS_NOWHERE   /* Store ENV in memory only */
 403 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
 404 #define CONFIG_ENV_SIZE         0x2000
 405 #endif
 406 #else
 407 #define CONFIG_ENV_IS_IN_FLASH
 408 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
 409 #define CONFIG_ENV_SIZE         0x2000
 410 #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K (one sector) */
 411 #endif
 412
 413 #define CONFIG_LOADS_ECHO               /* echo on for serial download */
 414 #define CONFIG_SYS_LOADS_BAUD_CHANGE    /* allow baudrate change */
 415
 416 /*
 417  * Command line configuration.
 418  */
 419 #define CONFIG_CMD_IRQ
 420 #define CONFIG_CMD_PING
 421 #define CONFIG_CMD_I2C
 422 #define CONFIG_CMD_MII
 423 #define CONFIG_CMD_REGINFO
 424
 425 /*
 426  * USB
 427  */
 428 #define CONFIG_HAS_FSL_DR_USB
 429
 430 #if defined(CONFIG_HAS_FSL_DR_USB)
 431 #define CONFIG_USB_EHCI
 432
 433 #ifdef CONFIG_USB_EHCI
 434 #define CONFIG_CMD_USB
 435 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 436 #define CONFIG_USB_EHCI_FSL
 437 #define CONFIG_USB_STORAGE
 438 #endif
 439 #endif
 440
 441 #define CONFIG_MMC
 442
 443 #ifdef CONFIG_MMC
 444 #define CONFIG_FSL_ESDHC
 445 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 446 #define CONFIG_CMD_MMC
 447 #define CONFIG_GENERIC_MMC
 448 #endif
 449
 450 #if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) \
 451                  || defined(CONFIG_FSL_SATA)
 452 #define CONFIG_CMD_EXT2
 453 #define CONFIG_CMD_FAT
 454 #define CONFIG_DOS_PARTITION
 455 #endif
 456
 457 #undef CONFIG_WATCHDOG  /* watchdog disabled */
 458
 459 /*
 460  * Miscellaneous configurable options
 461  */
 462 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
 463 #define CONFIG_CMDLINE_EDITING                  /* Command-line editing */
 464 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 465 #if defined(CONFIG_CMD_KGDB)
 466 #define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size */
 467 #else
 468 #define CONFIG_SYS_CBSIZE       256             /* Console I/O Buffer Size */
 469 #endif
 470 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 471         /* Print Buffer Size */
 472 #define CONFIG_SYS_MAXARGS      16      /* max number of command args */
 473 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
 474
 475 /*
 476  * For booting Linux, the board info and command line data
 477  * have to be in the first 64 MB of memory, since this is
 478  * the maximum mapped by the Linux kernel during initialization.
 479  */
 480 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial Memory for Linux*/
 481 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 482
 483 /*
 484  * Environment Configuration
 485  */
 486 #define CONFIG_HOSTNAME         unknown
 487 #define CONFIG_ROOTPATH         "/opt/nfsroot"
 488 #define CONFIG_BOOTFILE         "uImage"
 489 #define CONFIG_UBOOTPATH        u-boot.bin /* U-Boot image on TFTP server */
 490
 491 /* default location for tftp and bootm */
 492 #define CONFIG_LOADADDR 1000000
 493
 494 #define CONFIG_BOOTDELAY 10     /* -1 disables auto-boot */
 495 #define CONFIG_BOOTARGS /* the boot command will set bootargs */
 496
 497 #define CONFIG_BAUDRATE 115200
 498
 499 #define CONFIG_EXTRA_ENV_SETTINGS       \
 500 "netdev=eth0\0" \
 501 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"     \
 502 "loadaddr=1000000\0"    \
 503 "bootfile=uImage\0"     \
 504 "dtbfile=twr-p1025twr.dtb\0"    \
 505 "ramdiskfile=rootfs.ext2.gz.uboot\0"    \
 506 "qefirmwarefile=fsl_qe_ucode_1021_10_A.bin\0"   \
 507 "tftpflash=tftpboot $loadaddr $uboot; " \
 508         "protect off " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
 509         "erase " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; "      \
 510         "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize; " \
 511         "protect on " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
 512         "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize\0" \
 513 "kernelflash=tftpboot $loadaddr $bootfile; "    \
 514         "protect off 0xefa80000 +$filesize; "   \
 515         "erase 0xefa80000 +$filesize; " \
 516         "cp.b $loadaddr 0xefa80000 $filesize; " \
 517         "protect on 0xefa80000 +$filesize; "    \
 518         "cmp.b $loadaddr 0xefa80000 $filesize\0"        \
 519 "dtbflash=tftpboot $loadaddr $dtbfile; "        \
 520         "protect off 0xefe80000 +$filesize; "   \
 521         "erase 0xefe80000 +$filesize; " \
 522         "cp.b $loadaddr 0xefe80000 $filesize; " \
 523         "protect on 0xefe80000 +$filesize; "    \
 524         "cmp.b $loadaddr 0xefe80000 $filesize\0"        \
 525 "ramdiskflash=tftpboot $loadaddr $ramdiskfile; "        \
 526         "protect off 0xeeb80000 +$filesize; "   \
 527         "erase 0xeeb80000 +$filesize; " \
 528         "cp.b $loadaddr 0xeeb80000 $filesize; " \
 529         "protect on 0xeeb80000 +$filesize; "    \
 530         "cmp.b $loadaddr 0xeeb80000 $filesize\0"        \
 531 "qefirmwareflash=tftpboot $loadaddr $qefirmwarefile; "  \
 532         "protect off 0xefec0000 +$filesize; "   \
 533         "erase 0xefec0000 +$filesize; " \
 534         "cp.b $loadaddr 0xefec0000 $filesize; " \
 535         "protect on 0xefec0000 +$filesize; "    \
 536         "cmp.b $loadaddr 0xefec0000 $filesize\0"        \
 537 "consoledev=ttyS0\0"    \
 538 "ramdiskaddr=2000000\0" \
 539 "ramdiskfile=rootfs.ext2.gz.uboot\0"    \
 540 "fdtaddr=c00000\0"      \
 541 "bdev=sda1\0"   \
 542 "norbootaddr=ef080000\0"        \
 543 "norfdtaddr=ef040000\0" \
 544 "ramdisk_size=120000\0" \
 545 "usbboot=setenv bootargs root=/dev/sda1 rw rootdelay=5 " \
 546 "console=$consoledev,$baudrate $othbootargs ; bootm 0xefa80000 - 0xefe80000"
 547
 548 #define CONFIG_NFSBOOTCOMMAND   \
 549 "setenv bootargs root=/dev/nfs rw "     \
 550 "nfsroot=$serverip:$rootpath "  \
 551 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 552 "console=$consoledev,$baudrate $othbootargs;" \
 553 "tftp $loadaddr $bootfile&&"    \
 554 "tftp $fdtaddr $fdtfile&&"      \
 555 "bootm $loadaddr - $fdtaddr"
 556
 557 #define CONFIG_HDBOOT   \
 558 "setenv bootargs root=/dev/$bdev rw rootdelay=30 "      \
 559 "console=$consoledev,$baudrate $othbootargs;" \
 560 "usb start;"    \
 561 "ext2load usb 0:1 $loadaddr /boot/$bootfile;"   \
 562 "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;"     \
 563 "bootm $loadaddr - $fdtaddr"
 564
 565 #define CONFIG_USB_FAT_BOOT     \
 566 "setenv bootargs root=/dev/ram rw "     \
 567 "console=$consoledev,$baudrate $othbootargs " \
 568 "ramdisk_size=$ramdisk_size;"   \
 569 "usb start;"    \
 570 "fatload usb 0:2 $loadaddr $bootfile;"  \
 571 "fatload usb 0:2 $fdtaddr $fdtfile;"    \
 572 "fatload usb 0:2 $ramdiskaddr $ramdiskfile;"    \
 573 "bootm $loadaddr $ramdiskaddr $fdtaddr"
 574
 575 #define CONFIG_USB_EXT2_BOOT    \
 576 "setenv bootargs root=/dev/ram rw "     \
 577 "console=$consoledev,$baudrate $othbootargs " \
 578 "ramdisk_size=$ramdisk_size;"   \
 579 "usb start;"    \
 580 "ext2load usb 0:4 $loadaddr $bootfile;" \
 581 "ext2load usb 0:4 $fdtaddr $fdtfile;" \
 582 "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \
 583 "bootm $loadaddr $ramdiskaddr $fdtaddr"
 584
 585 #define CONFIG_NORBOOT  \
 586 "setenv bootargs root=/dev/mtdblock3 rw "       \
 587 "console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;"  \
 588 "bootm $norbootaddr - $norfdtaddr"
 589
 590 #define CONFIG_RAMBOOTCOMMAND_TFTP      \
 591 "setenv bootargs root=/dev/ram rw "     \
 592 "console=$consoledev,$baudrate $othbootargs " \
 593 "ramdisk_size=$ramdisk_size;"   \
 594 "tftp $ramdiskaddr $ramdiskfile;"       \
 595 "tftp $loadaddr $bootfile;"     \
 596 "tftp $fdtaddr $fdtfile;"       \
 597 "bootm $loadaddr $ramdiskaddr $fdtaddr"
 598
 599 #define CONFIG_RAMBOOTCOMMAND   \
 600 "setenv bootargs root=/dev/ram rw "     \
 601 "console=$consoledev,$baudrate $othbootargs " \
 602 "ramdisk_size=$ramdisk_size;"   \
 603 "bootm 0xefa80000 0xeeb80000 0xefe80000"
 604
 605 #define CONFIG_BOOTCOMMAND      CONFIG_RAMBOOTCOMMAND
 606
 607 #endif /* __CONFIG_H */