include/configs/sbc8349.h

   1 /*
   2  * WindRiver SBC8349 U-Boot configuration file.
   3  * Copyright (c) 2006, 2007 Wind River Systems, Inc.
   4  *
   5  * Paul Gortmaker <paul.gortmaker@windriver.com>
   6  * Based on the MPC8349EMDS config.
   7  *
   8  * SPDX-License-Identifier:     GPL-2.0+
   9  */
  10
  11 /*
  12  * sbc8349 board configuration file.
  13  */
  14
  15 #ifndef __CONFIG_H
  16 #define __CONFIG_H
  17
  18 #define CONFIG_DISPLAY_BOARDINFO
  19
  20 /*
  21  * High Level Configuration Options
  22  */
  23 #define CONFIG_E300             1       /* E300 Family */
  24 #define CONFIG_MPC834x          1       /* MPC834x family */
  25 #define CONFIG_MPC8349          1       /* MPC8349 specific */
  26 #define CONFIG_SBC8349          1       /* WRS SBC8349 board specific */
  27
  28 #define CONFIG_SYS_TEXT_BASE    0xFF800000
  29
  30 /* Don't enable PCI2 on sbc834x - it doesn't exist physically. */
  31 #undef CONFIG_MPC83XX_PCI2              /* support for 2nd PCI controller */
  32
  33 /*
  34  * The default if PCI isn't enabled, or if no PCI clk setting is given
  35  * is 66MHz; this is what the board defaults to when the PCI slot is
  36  * physically empty.  The board will automatically (i.e w/o jumpers)
  37  * clock down to 33MHz if you insert a 33MHz PCI card.
  38  */
  39 #ifdef CONFIG_PCI_33M
  40 #define CONFIG_83XX_CLKIN       33000000        /* in Hz */
  41 #else   /* 66M */
  42 #define CONFIG_83XX_CLKIN       66000000        /* in Hz */
  43 #endif
  44
  45 #ifndef CONFIG_SYS_CLK_FREQ
  46 #ifdef CONFIG_PCI_33M
  47 #define CONFIG_SYS_CLK_FREQ     33000000
  48 #define HRCWL_CSB_TO_CLKIN      HRCWL_CSB_TO_CLKIN_8X1
  49 #else   /* 66M */
  50 #define CONFIG_SYS_CLK_FREQ     66000000
  51 #define HRCWL_CSB_TO_CLKIN      HRCWL_CSB_TO_CLKIN_4X1
  52 #endif
  53 #endif
  54
  55 #undef CONFIG_BOARD_EARLY_INIT_F                /* call board_pre_init */
  56
  57 #define CONFIG_SYS_IMMR         0xE0000000
  58
  59 #undef CONFIG_SYS_DRAM_TEST             /* memory test, takes time */
  60 #define CONFIG_SYS_MEMTEST_START        0x00000000      /* memtest region */
  61 #define CONFIG_SYS_MEMTEST_END          0x00100000
  62
  63 /*
  64  * DDR Setup
  65  */
  66 #undef CONFIG_DDR_ECC                   /* only for ECC DDR module */
  67 #undef CONFIG_DDR_ECC_CMD               /* use DDR ECC user commands */
  68 #define CONFIG_SPD_EEPROM               /* use SPD EEPROM for DDR setup*/
  69 #define CONFIG_SYS_83XX_DDR_USES_CS0    /* WRS; Fsl board uses CS2/CS3 */
  70
  71 /*
  72  * 32-bit data path mode.
  73  *
  74  * Please note that using this mode for devices with the real density of 64-bit
  75  * effectively reduces the amount of available memory due to the effect of
  76  * wrapping around while translating address to row/columns, for example in the
  77  * 256MB module the upper 128MB get aliased with contents of the lower
  78  * 128MB); normally this define should be used for devices with real 32-bit
  79  * data path.
  80  */
  81 #undef CONFIG_DDR_32BIT
  82
  83 #define CONFIG_SYS_DDR_BASE             0x00000000 /* DDR is system memory*/
  84 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_BASE
  85 #define CONFIG_SYS_DDR_SDRAM_BASE       CONFIG_SYS_DDR_BASE
  86 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL   (DDR_SDRAM_CLK_CNTL_SS_EN | \
  87                                 DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075)
  88 #define CONFIG_DDR_2T_TIMING
  89
  90 #if defined(CONFIG_SPD_EEPROM)
  91 /*
  92  * Determine DDR configuration from I2C interface.
  93  */
  94 #define SPD_EEPROM_ADDRESS      0x52            /* DDR DIMM */
  95
  96 #else
  97 /*
  98  * Manually set up DDR parameters
  99  * NB: manual DDR setup untested on sbc834x
 100  */
 101 #define CONFIG_SYS_DDR_SIZE             256             /* MB */
 102 #define CONFIG_SYS_DDR_CS2_CONFIG       (CSCONFIG_EN \
 103                                         | CSCONFIG_ROW_BIT_13 \
 104                                         | CSCONFIG_COL_BIT_10)
 105 #define CONFIG_SYS_DDR_TIMING_1 0x36332321
 106 #define CONFIG_SYS_DDR_TIMING_2 0x00000800      /* P9-45,may need tuning */
 107 #define CONFIG_SYS_DDR_CONTROL  0xc2000000      /* unbuffered,no DYN_PWR */
 108 #define CONFIG_SYS_DDR_INTERVAL 0x04060100      /* autocharge,no open page */
 109
 110 #if defined(CONFIG_DDR_32BIT)
 111 /* set burst length to 8 for 32-bit data path */
 112                                 /* DLL,normal,seq,4/2.5, 8 burst len */
 113 #define CONFIG_SYS_DDR_MODE     0x00000023
 114 #else
 115 /* the default burst length is 4 - for 64-bit data path */
 116                                 /* DLL,normal,seq,4/2.5, 4 burst len */
 117 #define CONFIG_SYS_DDR_MODE     0x00000022
 118 #endif
 119 #endif
 120
 121 /*
 122  * SDRAM on the Local Bus
 123  */
 124 #define CONFIG_SYS_LBC_SDRAM_BASE       0xF0000000      /* Localbus SDRAM */
 125 #define CONFIG_SYS_LBC_SDRAM_SIZE       64              /* LBC SDRAM is 64MB */
 126
 127 /*
 128  * FLASH on the Local Bus
 129  */
 130 #define CONFIG_SYS_FLASH_CFI            /* use the Common Flash Interface */
 131 #define CONFIG_FLASH_CFI_DRIVER         /* use the CFI driver */
 132 #define CONFIG_SYS_FLASH_BASE           0xFF800000      /* start of FLASH   */
 133 #define CONFIG_SYS_FLASH_SIZE           8               /* flash size in MB */
 134 /* #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE */
 135
 136 #define CONFIG_SYS_BR0_PRELIM           (CONFIG_SYS_FLASH_BASE \
 137                                         | BR_PS_16      /* 16 bit port */ \
 138                                         | BR_MS_GPCM    /* MSEL = GPCM */ \
 139                                         | BR_V)         /* valid */
 140
 141 #define CONFIG_SYS_OR0_PRELIM           (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
 142                                         | OR_GPCM_XAM \
 143                                         | OR_GPCM_CSNT \
 144                                         | OR_GPCM_ACS_DIV2 \
 145                                         | OR_GPCM_XACS \
 146                                         | OR_GPCM_SCY_15 \
 147                                         | OR_GPCM_TRLX_SET \
 148                                         | OR_GPCM_EHTR_SET \
 149                                         | OR_GPCM_EAD)
 150                                         /* 0xFF806FF7 */
 151
 152                                         /* window base at flash base */
 153 #define CONFIG_SYS_LBLAWBAR0_PRELIM     CONFIG_SYS_FLASH_BASE
 154 #define CONFIG_SYS_LBLAWAR0_PRELIM      (LBLAWAR_EN | LBLAWAR_8MB)
 155
 156 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 157 #define CONFIG_SYS_MAX_FLASH_SECT       64      /* sectors per device */
 158
 159 #undef CONFIG_SYS_FLASH_CHECKSUM
 160 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 161 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 162
 163 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
 164
 165 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 166 #define CONFIG_SYS_RAMBOOT
 167 #else
 168 #undef  CONFIG_SYS_RAMBOOT
 169 #endif
 170
 171 #define CONFIG_SYS_INIT_RAM_LOCK        1
 172                                         /* Initial RAM address */
 173 #define CONFIG_SYS_INIT_RAM_ADDR        0xFD000000
 174                                         /* Size of used area in RAM*/
 175 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000
 176
 177 #define CONFIG_SYS_GBL_DATA_OFFSET      \
 178                         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 179 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 180
 181 #define CONFIG_SYS_MONITOR_LEN  (256 * 1024)    /* Reserve 256 kB for Mon */
 182 #define CONFIG_SYS_MALLOC_LEN   (256 * 1024)    /* Reserved for malloc */
 183
 184 /*
 185  * Local Bus LCRR and LBCR regs
 186  *    LCRR:  DLL bypass, Clock divider is 4
 187  * External Local Bus rate is
 188  *    CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
 189  */
 190 #define CONFIG_SYS_LCRR_DBYP    LCRR_DBYP
 191 #define CONFIG_SYS_LCRR_CLKDIV  LCRR_CLKDIV_4
 192 #define CONFIG_SYS_LBC_LBCR     0x00000000
 193
 194 #undef CONFIG_SYS_LB_SDRAM      /* if board has SDRAM on local bus */
 195
 196 #ifdef CONFIG_SYS_LB_SDRAM
 197 /* Local bus BR2, OR2 definition for SDRAM if soldered on the board*/
 198 /*
 199  * Base Register 2 and Option Register 2 configure SDRAM.
 200  * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
 201  *
 202  * For BR2, need:
 203  *    Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
 204  *    port-size = 32-bits = BR2[19:20] = 11
 205  *    no parity checking = BR2[21:22] = 00
 206  *    SDRAM for MSEL = BR2[24:26] = 011
 207  *    Valid = BR[31] = 1
 208  *
 209  * 0    4    8    12   16   20   24   28
 210  * 1111 0000 0000 0000 0001 1000 0110 0001 = F0001861
 211  */
 212
 213 #define CONFIG_SYS_BR2_PRELIM           (CONFIG_SYS_LBC_SDRAM_BASE \
 214                                         | BR_PS_32 \
 215                                         | BR_MS_SDRAM \
 216                                         | BR_V)
 217                                         /* 0xF0001861 */
 218 #define CONFIG_SYS_LBLAWBAR2_PRELIM     CONFIG_SYS_LBC_SDRAM_BASE
 219 #define CONFIG_SYS_LBLAWAR2_PRELIM      (LBLAWAR_EN | LBLAWAR_64MB)
 220
 221 /*
 222  * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
 223  *
 224  * For OR2, need:
 225  *    64MB mask for AM, OR2[0:7] = 1111 1100
 226  *                 XAM, OR2[17:18] = 11
 227  *    9 columns OR2[19-21] = 010
 228  *    13 rows   OR2[23-25] = 100
 229  *    EAD set for extra time OR[31] = 1
 230  *
 231  * 0    4    8    12   16   20   24   28
 232  * 1111 1100 0000 0000 0110 1001 0000 0001 = FC006901
 233  */
 234
 235 #define CONFIG_SYS_OR2_PRELIM   (MEG_TO_AM(CONFIG_SYS_LBC_SDRAM_SIZE) \
 236                         | OR_SDRAM_XAM \
 237                         | ((9 - OR_SDRAM_MIN_COLS) << OR_SDRAM_COLS_SHIFT) \
 238                         | ((13 - OR_SDRAM_MIN_ROWS) << OR_SDRAM_ROWS_SHIFT) \
 239                         | OR_SDRAM_EAD)
 240                         /* 0xFC006901 */
 241
 242                                 /* LB sdram refresh timer, about 6us */
 243 #define CONFIG_SYS_LBC_LSRT     0x32000000
 244                                 /* LB refresh timer prescal, 266MHz/32 */
 245 #define CONFIG_SYS_LBC_MRTPR    0x20000000
 246
 247 #define CONFIG_SYS_LBC_LSDMR_COMMON     (LSDMR_RFEN \
 248                                         | LSDMR_BSMA1516 \
 249                                         | LSDMR_RFCR8 \
 250                                         | LSDMR_PRETOACT6 \
 251                                         | LSDMR_ACTTORW3 \
 252                                         | LSDMR_BL8 \
 253                                         | LSDMR_WRC3 \
 254                                         | LSDMR_CL3)
 255
 256 /*
 257  * SDRAM Controller configuration sequence.
 258  */
 259 #define CONFIG_SYS_LBC_LSDMR_1  (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_PCHALL)
 260 #define CONFIG_SYS_LBC_LSDMR_2  (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
 261 #define CONFIG_SYS_LBC_LSDMR_3  (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
 262 #define CONFIG_SYS_LBC_LSDMR_4  (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW)
 263 #define CONFIG_SYS_LBC_LSDMR_5  (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL)
 264 #endif
 265
 266 /*
 267  * Serial Port
 268  */
 269 #define CONFIG_CONS_INDEX     1
 270 #define CONFIG_SYS_NS16550_SERIAL
 271 #define CONFIG_SYS_NS16550_REG_SIZE    1
 272 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 273
 274 #define CONFIG_SYS_BAUDRATE_TABLE  \
 275                 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 276
 277 #define CONFIG_SYS_NS16550_COM1        (CONFIG_SYS_IMMR+0x4500)
 278 #define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_IMMR+0x4600)
 279
 280 #define CONFIG_CMDLINE_EDITING  1       /* add command line history     */
 281 #define CONFIG_AUTO_COMPLETE            /* add autocompletion support   */
 282 /* Use the HUSH parser */
 283 #define CONFIG_SYS_HUSH_PARSER
 284
 285 /* I2C */
 286 #define CONFIG_SYS_I2C
 287 #define CONFIG_SYS_I2C_FSL
 288 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 289 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 290 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 291 #define CONFIG_SYS_FSL_I2C2_SPEED       400000
 292 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 293 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 294 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x69}, {1, 0x69} }
 295 /* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */
 296
 297 /* TSEC */
 298 #define CONFIG_SYS_TSEC1_OFFSET 0x24000
 299 #define CONFIG_SYS_TSEC1        (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
 300 #define CONFIG_SYS_TSEC2_OFFSET 0x25000
 301 #define CONFIG_SYS_TSEC2        (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
 302
 303 /*
 304  * General PCI
 305  * Addresses are mapped 1-1.
 306  */
 307 #define CONFIG_SYS_PCI1_MEM_BASE        0x80000000
 308 #define CONFIG_SYS_PCI1_MEM_PHYS        CONFIG_SYS_PCI1_MEM_BASE
 309 #define CONFIG_SYS_PCI1_MEM_SIZE        0x10000000      /* 256M */
 310 #define CONFIG_SYS_PCI1_MMIO_BASE       0x90000000
 311 #define CONFIG_SYS_PCI1_MMIO_PHYS       CONFIG_SYS_PCI1_MMIO_BASE
 312 #define CONFIG_SYS_PCI1_MMIO_SIZE       0x10000000      /* 256M */
 313 #define CONFIG_SYS_PCI1_IO_BASE         0x00000000
 314 #define CONFIG_SYS_PCI1_IO_PHYS         0xE2000000
 315 #define CONFIG_SYS_PCI1_IO_SIZE         0x00100000      /* 1M */
 316
 317 #define CONFIG_SYS_PCI2_MEM_BASE        0xA0000000
 318 #define CONFIG_SYS_PCI2_MEM_PHYS        CONFIG_SYS_PCI2_MEM_BASE
 319 #define CONFIG_SYS_PCI2_MEM_SIZE        0x10000000      /* 256M */
 320 #define CONFIG_SYS_PCI2_MMIO_BASE       0xB0000000
 321 #define CONFIG_SYS_PCI2_MMIO_PHYS       CONFIG_SYS_PCI2_MMIO_BASE
 322 #define CONFIG_SYS_PCI2_MMIO_SIZE       0x10000000      /* 256M */
 323 #define CONFIG_SYS_PCI2_IO_BASE         0x00000000
 324 #define CONFIG_SYS_PCI2_IO_PHYS         0xE2100000
 325 #define CONFIG_SYS_PCI2_IO_SIZE         0x00100000      /* 1M */
 326
 327 #if defined(CONFIG_PCI)
 328
 329 #define PCI_64BIT
 330 #define PCI_ONE_PCI1
 331 #if defined(PCI_64BIT)
 332 #undef PCI_ALL_PCI1
 333 #undef PCI_TWO_PCI1
 334 #undef PCI_ONE_PCI1
 335 #endif
 336
 337 #define CONFIG_PCI_PNP          /* do pci plug-and-play */
 338
 339 #undef CONFIG_EEPRO100
 340 #undef CONFIG_TULIP
 341
 342 #if !defined(CONFIG_PCI_PNP)
 343         #define PCI_ENET0_IOADDR        0xFIXME
 344         #define PCI_ENET0_MEMADDR       0xFIXME
 345         #define PCI_IDSEL_NUMBER        0xFIXME
 346 #endif
 347
 348 #undef CONFIG_PCI_SCAN_SHOW             /* show pci devices on startup */
 349 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057  /* Motorola */
 350
 351 #endif  /* CONFIG_PCI */
 352
 353 /*
 354  * TSEC configuration
 355  */
 356 #define CONFIG_TSEC_ENET                /* TSEC ethernet support */
 357
 358 #if defined(CONFIG_TSEC_ENET)
 359
 360 #define CONFIG_TSEC1    1
 361 #define CONFIG_TSEC1_NAME       "TSEC0"
 362 #define CONFIG_TSEC2    1
 363 #define CONFIG_TSEC2_NAME       "TSEC1"
 364 #define CONFIG_PHY_BCM5421S     1
 365 #define TSEC1_PHY_ADDR          0x19
 366 #define TSEC2_PHY_ADDR          0x1a
 367 #define TSEC1_PHYIDX            0
 368 #define TSEC2_PHYIDX            0
 369 #define TSEC1_FLAGS             TSEC_GIGABIT
 370 #define TSEC2_FLAGS             TSEC_GIGABIT
 371
 372 /* Options are: TSEC[0-1] */
 373 #define CONFIG_ETHPRIME         "TSEC0"
 374
 375 #endif  /* CONFIG_TSEC_ENET */
 376
 377 /*
 378  * Environment
 379  */
 380 #ifndef CONFIG_SYS_RAMBOOT
 381         #define CONFIG_ENV_IS_IN_FLASH  1
 382         #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + 0x40000)
 383         #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K(one sector) for env */
 384         #define CONFIG_ENV_SIZE         0x2000
 385
 386 /* Address and size of Redundant Environment Sector     */
 387 #define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
 388 #define CONFIG_ENV_SIZE_REDUND  (CONFIG_ENV_SIZE)
 389
 390 #else
 391         #define CONFIG_SYS_NO_FLASH     1       /* Flash is not usable now */
 392         #define CONFIG_ENV_IS_NOWHERE   1       /* Store ENV in memory only */
 393         #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
 394         #define CONFIG_ENV_SIZE         0x2000
 395 #endif
 396
 397 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 398 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 399
 400
 401 /*
 402  * BOOTP options
 403  */
 404 #define CONFIG_BOOTP_BOOTFILESIZE
 405 #define CONFIG_BOOTP_BOOTPATH
 406 #define CONFIG_BOOTP_GATEWAY
 407 #define CONFIG_BOOTP_HOSTNAME
 408
 409
 410 /*
 411  * Command line configuration.
 412  */
 413 #define CONFIG_CMD_I2C
 414 #define CONFIG_CMD_MII
 415 #define CONFIG_CMD_PING
 416
 417 #if defined(CONFIG_PCI)
 418     #define CONFIG_CMD_PCI
 419 #endif
 420
 421 #undef CONFIG_WATCHDOG                  /* watchdog disabled */
 422
 423 /*
 424  * Miscellaneous configurable options
 425  */
 426 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
 427 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 428
 429 #if defined(CONFIG_CMD_KGDB)
 430         #define CONFIG_SYS_CBSIZE       1024    /* Console I/O Buffer Size */
 431 #else
 432         #define CONFIG_SYS_CBSIZE       256     /* Console I/O Buffer Size */
 433 #endif
 434
 435                                 /* Print Buffer Size */
 436 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
 437 #define CONFIG_SYS_MAXARGS      16      /* max number of command args */
 438                                 /* Boot Argument Buffer Size */
 439 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE
 440
 441 /*
 442  * For booting Linux, the board info and command line data
 443  * have to be in the first 256 MB of memory, since this is
 444  * the maximum mapped by the Linux kernel during initialization.
 445  */
 446                                 /* Initial Memory map for Linux*/
 447 #define CONFIG_SYS_BOOTMAPSZ    (256 << 20)
 448
 449 #define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST  */
 450
 451 #if 1 /*528/264*/
 452 #define CONFIG_SYS_HRCW_LOW (\
 453         HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
 454         HRCWL_DDR_TO_SCB_CLK_1X1 |\
 455         HRCWL_CSB_TO_CLKIN |\
 456         HRCWL_VCO_1X2 |\
 457         HRCWL_CORE_TO_CSB_2X1)
 458 #elif 0 /*396/132*/
 459 #define CONFIG_SYS_HRCW_LOW (\
 460         HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
 461         HRCWL_DDR_TO_SCB_CLK_1X1 |\
 462         HRCWL_CSB_TO_CLKIN |\
 463         HRCWL_VCO_1X4 |\
 464         HRCWL_CORE_TO_CSB_3X1)
 465 #elif 0 /*264/132*/
 466 #define CONFIG_SYS_HRCW_LOW (\
 467         HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
 468         HRCWL_DDR_TO_SCB_CLK_1X1 |\
 469         HRCWL_CSB_TO_CLKIN |\
 470         HRCWL_VCO_1X4 |\
 471         HRCWL_CORE_TO_CSB_2X1)
 472 #elif 0 /*132/132*/
 473 #define CONFIG_SYS_HRCW_LOW (\
 474         HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
 475         HRCWL_DDR_TO_SCB_CLK_1X1 |\
 476         HRCWL_CSB_TO_CLKIN |\
 477         HRCWL_VCO_1X4 |\
 478         HRCWL_CORE_TO_CSB_1X1)
 479 #elif 0 /*264/264 */
 480 #define CONFIG_SYS_HRCW_LOW (\
 481         HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
 482         HRCWL_DDR_TO_SCB_CLK_1X1 |\
 483         HRCWL_CSB_TO_CLKIN |\
 484         HRCWL_VCO_1X4 |\
 485         HRCWL_CORE_TO_CSB_1X1)
 486 #endif
 487
 488 #if defined(PCI_64BIT)
 489 #define CONFIG_SYS_HRCW_HIGH (\
 490         HRCWH_PCI_HOST |\
 491         HRCWH_64_BIT_PCI |\
 492         HRCWH_PCI1_ARBITER_ENABLE |\
 493         HRCWH_PCI2_ARBITER_DISABLE |\
 494         HRCWH_CORE_ENABLE |\
 495         HRCWH_FROM_0X00000100 |\
 496         HRCWH_BOOTSEQ_DISABLE |\
 497         HRCWH_SW_WATCHDOG_DISABLE |\
 498         HRCWH_ROM_LOC_LOCAL_16BIT |\
 499         HRCWH_TSEC1M_IN_GMII |\
 500         HRCWH_TSEC2M_IN_GMII)
 501 #else
 502 #define CONFIG_SYS_HRCW_HIGH (\
 503         HRCWH_PCI_HOST |\
 504         HRCWH_32_BIT_PCI |\
 505         HRCWH_PCI1_ARBITER_ENABLE |\
 506         HRCWH_PCI2_ARBITER_ENABLE |\
 507         HRCWH_CORE_ENABLE |\
 508         HRCWH_FROM_0X00000100 |\
 509         HRCWH_BOOTSEQ_DISABLE |\
 510         HRCWH_SW_WATCHDOG_DISABLE |\
 511         HRCWH_ROM_LOC_LOCAL_16BIT |\
 512         HRCWH_TSEC1M_IN_GMII |\
 513         HRCWH_TSEC2M_IN_GMII)
 514 #endif
 515
 516 /* System IO Config */
 517 #define CONFIG_SYS_SICRH 0
 518 #define CONFIG_SYS_SICRL SICRL_LDP_A
 519
 520 #define CONFIG_SYS_HID0_INIT    0x000000000
 521 #define CONFIG_SYS_HID0_FINAL   (HID0_ENABLE_MACHINE_CHECK \
 522                                 | HID0_ENABLE_INSTRUCTION_CACHE)
 523
 524 /* #define CONFIG_SYS_HID0_FINAL        (\
 525         HID0_ENABLE_INSTRUCTION_CACHE |\
 526         HID0_ENABLE_M_BIT |\
 527         HID0_ENABLE_ADDRESS_BROADCAST) */
 528
 529
 530 #define CONFIG_SYS_HID2 HID2_HBE
 531
 532 #define CONFIG_HIGH_BATS        1       /* High BATs supported */
 533
 534 /* DDR @ 0x00000000 */
 535 #define CONFIG_SYS_IBAT0L       (CONFIG_SYS_SDRAM_BASE \
 536                                 | BATL_PP_RW \
 537                                 | BATL_MEMCOHERENCE)
 538 #define CONFIG_SYS_IBAT0U       (CONFIG_SYS_SDRAM_BASE \
 539                                 | BATU_BL_256M \
 540                                 | BATU_VS \
 541                                 | BATU_VP)
 542
 543 /* PCI @ 0x80000000 */
 544 #ifdef CONFIG_PCI
 545 #define CONFIG_PCI_INDIRECT_BRIDGE
 546 #define CONFIG_SYS_IBAT1L       (CONFIG_SYS_PCI1_MEM_BASE \
 547                                 | BATL_PP_RW \
 548                                 | BATL_MEMCOHERENCE)
 549 #define CONFIG_SYS_IBAT1U       (CONFIG_SYS_PCI1_MEM_BASE \
 550                                 | BATU_BL_256M \
 551                                 | BATU_VS \
 552                                 | BATU_VP)
 553 #define CONFIG_SYS_IBAT2L       (CONFIG_SYS_PCI1_MMIO_BASE \
 554                                 | BATL_PP_RW \
 555                                 | BATL_CACHEINHIBIT \
 556                                 | BATL_GUARDEDSTORAGE)
 557 #define CONFIG_SYS_IBAT2U       (CONFIG_SYS_PCI1_MMIO_BASE \
 558                                 | BATU_BL_256M \
 559                                 | BATU_VS \
 560                                 | BATU_VP)
 561 #else
 562 #define CONFIG_SYS_IBAT1L       (0)
 563 #define CONFIG_SYS_IBAT1U       (0)
 564 #define CONFIG_SYS_IBAT2L       (0)
 565 #define CONFIG_SYS_IBAT2U       (0)
 566 #endif
 567
 568 #ifdef CONFIG_MPC83XX_PCI2
 569 #define CONFIG_SYS_IBAT3L       (CONFIG_SYS_PCI2_MEM_BASE \
 570                                 | BATL_PP_RW \
 571                                 | BATL_MEMCOHERENCE)
 572 #define CONFIG_SYS_IBAT3U       (CONFIG_SYS_PCI2_MEM_BASE \
 573                                 | BATU_BL_256M \
 574                                 | BATU_VS \
 575                                 | BATU_VP)
 576 #define CONFIG_SYS_IBAT4L       (CONFIG_SYS_PCI2_MMIO_BASE \
 577                                 | BATL_PP_RW \
 578                                 | BATL_CACHEINHIBIT \
 579                                 | BATL_GUARDEDSTORAGE)
 580 #define CONFIG_SYS_IBAT4U       (CONFIG_SYS_PCI2_MMIO_BASE \
 581                                 | BATU_BL_256M \
 582                                 | BATU_VS \
 583                                 | BATU_VP)
 584 #else
 585 #define CONFIG_SYS_IBAT3L       (0)
 586 #define CONFIG_SYS_IBAT3U       (0)
 587 #define CONFIG_SYS_IBAT4L       (0)
 588 #define CONFIG_SYS_IBAT4U       (0)
 589 #endif
 590
 591 /* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 */
 592 #define CONFIG_SYS_IBAT5L       (CONFIG_SYS_IMMR \
 593                                 | BATL_PP_RW \
 594                                 | BATL_CACHEINHIBIT \
 595                                 | BATL_GUARDEDSTORAGE)
 596 #define CONFIG_SYS_IBAT5U       (CONFIG_SYS_IMMR \
 597                                 | BATU_BL_256M \
 598                                 | BATU_VS \
 599                                 | BATU_VP)
 600
 601 /* LBC SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
 602 #define CONFIG_SYS_IBAT6L       (CONFIG_SYS_LBC_SDRAM_BASE \
 603                                 | BATL_PP_RW \
 604                                 | BATL_MEMCOHERENCE \
 605                                 | BATL_GUARDEDSTORAGE)
 606 #define CONFIG_SYS_IBAT6U       (CONFIG_SYS_LBC_SDRAM_BASE \
 607                                 | BATU_BL_256M \
 608                                 | BATU_VS \
 609                                 | BATU_VP)
 610
 611 #define CONFIG_SYS_IBAT7L       (0)
 612 #define CONFIG_SYS_IBAT7U       (0)
 613
 614 #define CONFIG_SYS_DBAT0L       CONFIG_SYS_IBAT0L
 615 #define CONFIG_SYS_DBAT0U       CONFIG_SYS_IBAT0U
 616 #define CONFIG_SYS_DBAT1L       CONFIG_SYS_IBAT1L
 617 #define CONFIG_SYS_DBAT1U       CONFIG_SYS_IBAT1U
 618 #define CONFIG_SYS_DBAT2L       CONFIG_SYS_IBAT2L
 619 #define CONFIG_SYS_DBAT2U       CONFIG_SYS_IBAT2U
 620 #define CONFIG_SYS_DBAT3L       CONFIG_SYS_IBAT3L
 621 #define CONFIG_SYS_DBAT3U       CONFIG_SYS_IBAT3U
 622 #define CONFIG_SYS_DBAT4L       CONFIG_SYS_IBAT4L
 623 #define CONFIG_SYS_DBAT4U       CONFIG_SYS_IBAT4U
 624 #define CONFIG_SYS_DBAT5L       CONFIG_SYS_IBAT5L
 625 #define CONFIG_SYS_DBAT5U       CONFIG_SYS_IBAT5U
 626 #define CONFIG_SYS_DBAT6L       CONFIG_SYS_IBAT6L
 627 #define CONFIG_SYS_DBAT6U       CONFIG_SYS_IBAT6U
 628 #define CONFIG_SYS_DBAT7L       CONFIG_SYS_IBAT7L
 629 #define CONFIG_SYS_DBAT7U       CONFIG_SYS_IBAT7U
 630
 631 #if defined(CONFIG_CMD_KGDB)
 632 #define CONFIG_KGDB_BAUDRATE    230400  /* speed of kgdb serial port */
 633 #endif
 634
 635 /*
 636  * Environment Configuration
 637  */
 638 #define CONFIG_ENV_OVERWRITE
 639
 640 #if defined(CONFIG_TSEC_ENET)
 641 #define CONFIG_HAS_ETH0
 642 #define CONFIG_HAS_ETH1
 643 #endif
 644
 645 #define CONFIG_HOSTNAME         SBC8349
 646 #define CONFIG_ROOTPATH         "/tftpboot/rootfs"
 647 #define CONFIG_BOOTFILE         "uImage"
 648
 649                                 /* default location for tftp and bootm */
 650 #define CONFIG_LOADADDR         800000
 651
 652 #define CONFIG_BOOTDELAY        6       /* -1 disables auto-boot */
 653 #undef  CONFIG_BOOTARGS         /* the boot command will set bootargs */
 654
 655 #define CONFIG_BAUDRATE  115200
 656
 657 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 658         "netdev=eth0\0"                                                 \
 659         "hostname=sbc8349\0"                                            \
 660         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 661                 "nfsroot=${serverip}:${rootpath}\0"                     \
 662         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
 663         "addip=setenv bootargs ${bootargs} "                            \
 664                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
 665                 ":${hostname}:${netdev}:off panic=1\0"                  \
 666         "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
 667         "flash_nfs=run nfsargs addip addtty;"                           \
 668                 "bootm ${kernel_addr}\0"                                \
 669         "flash_self=run ramargs addip addtty;"                          \
 670                 "bootm ${kernel_addr} ${ramdisk_addr}\0"                \
 671         "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
 672                 "bootm\0"                                               \
 673         "load=tftp 100000 /tftpboot/sbc8349/u-boot.bin\0"               \
 674         "update=protect off ff800000 ff83ffff; "                        \
 675                 "era ff800000 ff83ffff; cp.b 100000 ff800000 ${filesize}\0" \
 676         "upd=run load update\0"                                         \
 677         "fdtaddr=780000\0"                                              \
 678         "fdtfile=sbc8349.dtb\0"                                         \
 679         ""
 680
 681 #define CONFIG_NFSBOOTCOMMAND                                           \
 682         "setenv bootargs root=/dev/nfs rw "                             \
 683                 "nfsroot=$serverip:$rootpath "                          \
 684                 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"   \
 685                                                         "$netdev:off "  \
 686                 "console=$consoledev,$baudrate $othbootargs;"           \
 687         "tftp $loadaddr $bootfile;"                                     \
 688         "tftp $fdtaddr $fdtfile;"                                       \
 689         "bootm $loadaddr - $fdtaddr"
 690
 691 #define CONFIG_RAMBOOTCOMMAND                                           \
 692         "setenv bootargs root=/dev/ram rw "                             \
 693                 "console=$consoledev,$baudrate $othbootargs;"           \
 694         "tftp $ramdiskaddr $ramdiskfile;"                               \
 695         "tftp $loadaddr $bootfile;"                                     \
 696         "tftp $fdtaddr $fdtfile;"                                       \
 697         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 698
 699 #define CONFIG_BOOTCOMMAND      "run flash_self"
 700
 701 #endif  /* __CONFIG_H */