include/configs/xtfpga.h

   1 /*
   2  * Copyright (C) 2007-2013 Tensilica, Inc.
   3  * Copyright (C) 2014 - 2016 Cadence Design Systems Inc.
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 #ifndef __CONFIG_H
   9 #define __CONFIG_H
  10
  11 #include <asm/arch/core.h>
  12 #include <asm/addrspace.h>
  13 #include <asm/config.h>
  14
  15 /*
  16  * The 'xtfpga' board describes a set of very similar boards with only minimal
  17  * differences.
  18  */
  19
  20 /*=====================*/
  21 /* Board and Processor */
  22 /*=====================*/
  23
  24 #define CONFIG_XTFPGA
  25
  26 /* FPGA CPU freq after init */
  27 #define CONFIG_SYS_CLK_FREQ             (gd->cpu_clk)
  28
  29 /*===================*/
  30 /* RAM Layout        */
  31 /*===================*/
  32
  33 #if XCHAL_HAVE_PTP_MMU
  34 #define CONFIG_SYS_MEMORY_BASE          \
  35         (XCHAL_VECBASE_RESET_VADDR - XCHAL_VECBASE_RESET_PADDR)
  36 #define CONFIG_SYS_IO_BASE              0xf0000000
  37 #else
  38 #define CONFIG_SYS_MEMORY_BASE          0x60000000
  39 #define CONFIG_SYS_IO_BASE              0x90000000
  40 #define CONFIG_MAX_MEM_MAPPED           0x10000000
  41 #endif
  42
  43 /* Onboard RAM sizes:
  44  *
  45  * LX60         0x04000000                64 MB
  46  * LX110        0x03000000                48 MB
  47  * LX200        0x06000000                96 MB
  48  * ML605        0x18000000               384 MB
  49  * KC705        0x38000000               896 MB
  50  *
  51  * noMMU configurations can only see first 256MB of onboard memory.
  52  */
  53
  54 #if XCHAL_HAVE_PTP_MMU || CONFIG_BOARD_SDRAM_SIZE < 0x10000000
  55 #define CONFIG_SYS_SDRAM_SIZE           CONFIG_BOARD_SDRAM_SIZE
  56 #else
  57 #define CONFIG_SYS_SDRAM_SIZE           0x10000000
  58 #endif
  59
  60 #define CONFIG_SYS_SDRAM_BASE           MEMADDR(0x00000000)
  61
  62 /* Lx60 can only map 128kb memory (instead of 256kb) when running under OCD */
  63 #ifdef CONFIG_XTFPGA_LX60
  64 # define CONFIG_SYS_MONITOR_LEN         0x00020000      /* 128KB */
  65 #else
  66 # define CONFIG_SYS_MONITOR_LEN         0x00040000      /* 256KB */
  67 #endif
  68
  69 #define CONFIG_SYS_STACKSIZE            (512 << 10)     /* stack 512KB */
  70 #define CONFIG_SYS_MALLOC_LEN           (256 << 10)     /* heap  256KB */
  71
  72 /* Linux boot param area in RAM (used only when booting linux) */
  73 #define CONFIG_SYS_BOOTPARAMS_LEN       (64  << 10)
  74
  75 /* Memory test is destructive so default must not overlap vectors or U-Boot*/
  76 #define CONFIG_SYS_MEMTEST_START        MEMADDR(0x01000000)
  77 #define CONFIG_SYS_MEMTEST_END          MEMADDR(0x02000000)
  78
  79 /* Load address for stand-alone applications.
  80  * MEMADDR cannot be used here, because the definition needs to be
  81  * a plain number as it's used as -Ttext argument for ld in standalone
  82  * example makefile.
  83  * Handle noMMU vs MMUv2 vs MMUv3 distinction here manually.
  84  */
  85 #if XCHAL_HAVE_PTP_MMU
  86 #if XCHAL_VECBASE_RESET_VADDR == XCHAL_VECBASE_RESET_PADDR
  87 #define CONFIG_STANDALONE_LOAD_ADDR     0x00800000
  88 #else
  89 #define CONFIG_STANDALONE_LOAD_ADDR     0xd0800000
  90 #endif
  91 #else
  92 #define CONFIG_STANDALONE_LOAD_ADDR     0x60800000
  93 #endif
  94
  95 #if defined(CONFIG_MAX_MEM_MAPPED) && \
  96         CONFIG_MAX_MEM_MAPPED < CONFIG_SYS_SDRAM_SIZE
  97 #define CONFIG_SYS_MEMORY_SIZE          CONFIG_MAX_MEM_MAPPED
  98 #else
  99 #define CONFIG_SYS_MEMORY_SIZE          CONFIG_SYS_SDRAM_SIZE
 100 #endif
 101
 102 #define CONFIG_SYS_MEMORY_TOP           MEMADDR(CONFIG_SYS_MEMORY_SIZE)
 103 #define CONFIG_SYS_TEXT_ADDR            \
 104         (CONFIG_SYS_MEMORY_TOP - CONFIG_SYS_MONITOR_LEN)
 105
 106 /* Used by tftpboot; env var 'loadaddr' */
 107 #define CONFIG_SYS_LOAD_ADDR            MEMADDR(0x02000000)
 108
 109 /*==============================*/
 110 /* U-Boot general configuration */
 111 /*==============================*/
 112
 113 #undef  CONFIG_USE_IRQ                  /* Keep it simple, poll only */
 114 #define CONFIG_BOARD_POSTCLK_INIT
 115 #define CONFIG_DISPLAY_BOARDINFO
 116 #define CONFIG_MISC_INIT_R
 117
 118 #define CONFIG_BOOTFILE                 "uImage"
 119         /* Console I/O Buffer Size  */
 120 #define CONFIG_SYS_CBSIZE               1024
 121         /* Prt buf */
 122 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE + \
 123                                          sizeof(CONFIG_SYS_PROMPT) + 16)
 124         /* max number of command args */
 125 #define CONFIG_SYS_MAXARGS              16
 126         /* Boot Argument Buffer Size */
 127 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE
 128
 129 /*=================*/
 130 /* U-Boot commands */
 131 /*=================*/
 132
 133 #define CONFIG_CMD_DIAG
 134 #define CONFIG_CMD_SAVES
 135
 136 /*==============================*/
 137 /* U-Boot autoboot configuration */
 138 /*==============================*/
 139
 140 #define CONFIG_BOOT_RETRY_TIME          60      /* retry after 60 secs */
 141
 142 #define CONFIG_AUTO_COMPLETE                    /* Support tab autocompletion */
 143 #define CONFIG_CMDLINE_EDITING
 144 #define CONFIG_SYS_LONGHELP
 145 #define CONFIG_CRC32_VERIFY
 146 #define CONFIG_MX_CYCLIC
 147 #define CONFIG_SHOW_BOOT_PROGRESS
 148
 149 #ifdef DEBUG
 150 #define CONFIG_PANIC_HANG               1       /* Require manual reboot */
 151 #endif
 152
 153
 154 /*=========================================*/
 155 /* FPGA Registers (board info and control) */
 156 /*=========================================*/
 157
 158 /*
 159  * These assume FPGA bitstreams from Tensilica release RB and up. Earlier
 160  * releases may not provide any/all of these registers or at these offsets.
 161  * Some of the FPGA registers are broken down into bitfields described by
 162  * SHIFT left amount and field WIDTH (bits), and also by a bitMASK.
 163  */
 164
 165 /* Date of FPGA bitstream build in binary coded decimal (BCD) */
 166 #define CONFIG_SYS_FPGAREG_DATE         IOADDR(0x0D020000)
 167 #define FPGAREG_MTH_SHIFT               24              /* BCD month 1..12 */
 168 #define FPGAREG_MTH_WIDTH               8
 169 #define FPGAREG_MTH_MASK                0xFF000000
 170 #define FPGAREG_DAY_SHIFT               16              /* BCD day 1..31 */
 171 #define FPGAREG_DAY_WIDTH               8
 172 #define FPGAREG_DAY_MASK                0x00FF0000
 173 #define FPGAREG_YEAR_SHIFT              0               /* BCD year 2001..9999*/
 174 #define FPGAREG_YEAR_WIDTH              16
 175 #define FPGAREG_YEAR_MASK               0x0000FFFF
 176
 177 /* FPGA core clock frequency in Hz (also input to UART) */
 178 #define CONFIG_SYS_FPGAREG_FREQ IOADDR(0x0D020004)      /* CPU clock frequency*/
 179
 180 /*
 181  * DIP switch (left=sw1=lsb=bit0, right=sw8=msb=bit7; off=0, on=1):
 182  *   Bits 0..5 set the lower 6 bits of the default ethernet MAC.
 183  *   Bit 6 is reserved for future use by Tensilica.
 184  *   Bit 7 maps the first 128KB of ROM address space at CONFIG_SYS_ROM_BASE to
 185  *   the base of flash * (when on/1) or to the base of RAM (when off/0).
 186  */
 187 #define CONFIG_SYS_FPGAREG_DIPSW        IOADDR(0x0D02000C)
 188 #define FPGAREG_MAC_SHIFT               0       /* Ethernet MAC bits 0..5 */
 189 #define FPGAREG_MAC_WIDTH               6
 190 #define FPGAREG_MAC_MASK                0x3f
 191 #define FPGAREG_BOOT_SHIFT              7       /* Boot ROM addr mapping */
 192 #define FPGAREG_BOOT_WIDTH              1
 193 #define FPGAREG_BOOT_MASK               0x80
 194 #define FPGAREG_BOOT_RAM                0
 195 #define FPGAREG_BOOT_FLASH              (1<<FPGAREG_BOOT_SHIFT)
 196
 197 /* Force hard reset of board by writing a code to this register */
 198 #define CONFIG_SYS_FPGAREG_RESET        IOADDR(0x0D020010) /* Reset board .. */
 199 #define CONFIG_SYS_FPGAREG_RESET_CODE   0x0000DEAD   /*  by writing this code */
 200
 201 /*====================*/
 202 /* Serial Driver Info */
 203 /*====================*/
 204
 205 #define CONFIG_SYS_NS16550_SERIAL
 206 #define CONFIG_SYS_NS16550_REG_SIZE     (-4)
 207 #define CONFIG_SYS_NS16550_COM1         IOADDR(0x0D050020) /* Base address */
 208
 209 /* Input clk to NS16550 (in Hz; the SYS_CLK_FREQ is in kHz) */
 210 #define CONFIG_SYS_NS16550_CLK          CONFIG_SYS_CLK_FREQ
 211 #define CONFIG_CONS_INDEX               1       /* use UART0 for console */
 212 #define CONFIG_BAUDRATE                 115200  /* Default baud rate */
 213 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200 }
 214
 215 /*======================*/
 216 /* Ethernet Driver Info */
 217 /*======================*/
 218
 219 #define CONFIG_ETHBASE                  00:50:C2:13:6f:00
 220 #define CONFIG_SYS_ETHOC_BASE           IOADDR(0x0d030000)
 221 #define CONFIG_SYS_ETHOC_BUFFER_ADDR    IOADDR(0x0D800000)
 222
 223 /*=====================*/
 224 /* Flash & Environment */
 225 /*=====================*/
 226
 227 #define CONFIG_SYS_FLASH_CFI
 228 #define CONFIG_FLASH_CFI_DRIVER                 /* use generic CFI driver */
 229 #define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_16BIT
 230 #define CONFIG_SYS_MAX_FLASH_BANKS      1
 231 #ifdef CONFIG_XTFPGA_LX60
 232 # define CONFIG_SYS_FLASH_SIZE          0x0040000       /* 4MB */
 233 # define CONFIG_SYS_FLASH_SECT_SZ       0x10000         /* block size 64KB */
 234 # define CONFIG_SYS_FLASH_PARMSECT_SZ   0x2000          /* param size  8KB */
 235 # define CONFIG_SYS_FLASH_BASE          IOADDR(0x08000000)
 236 # define CONFIG_SYS_MONITOR_BASE        CONFIG_SYS_FLASH_BASE
 237 #elif defined(CONFIG_XTFPGA_KC705)
 238 # define CONFIG_SYS_FLASH_SIZE          0x8000000       /* 128MB */
 239 # define CONFIG_SYS_FLASH_SECT_SZ       0x20000         /* block size 128KB */
 240 # define CONFIG_SYS_FLASH_PARMSECT_SZ   0x8000          /* param size 32KB */
 241 # define CONFIG_SYS_FLASH_BASE          IOADDR(0x00000000)
 242 # define CONFIG_SYS_MONITOR_BASE        IOADDR(0x06000000)
 243 #else
 244 # define CONFIG_SYS_FLASH_SIZE          0x1000000       /* 16MB */
 245 # define CONFIG_SYS_FLASH_SECT_SZ       0x20000         /* block size 128KB */
 246 # define CONFIG_SYS_FLASH_PARMSECT_SZ   0x8000          /* param size 32KB */
 247 # define CONFIG_SYS_FLASH_BASE          IOADDR(0x08000000)
 248 # define CONFIG_SYS_MONITOR_BASE        CONFIG_SYS_FLASH_BASE
 249 #endif
 250 #define CONFIG_SYS_MAX_FLASH_SECT       \
 251         (CONFIG_SYS_FLASH_SECT_SZ/CONFIG_SYS_FLASH_PARMSECT_SZ + \
 252          CONFIG_SYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ - 1)
 253 #define CONFIG_SYS_FLASH_PROTECTION             /* hw flash protection */
 254
 255 /*
 256  * Put environment in top block (64kB)
 257  * Another option would be to put env. in 2nd param block offs 8KB, size 8KB
 258  */
 259 #define CONFIG_ENV_IS_IN_FLASH
 260 #define CONFIG_ENV_OFFSET    (CONFIG_SYS_FLASH_SIZE - CONFIG_SYS_FLASH_SECT_SZ)
 261 #define CONFIG_ENV_SIZE      CONFIG_SYS_FLASH_SECT_SZ
 262
 263 /* print 'E' for empty sector on flinfo */
 264 #define CONFIG_SYS_FLASH_EMPTY_INFO
 265
 266 #endif /* __CONFIG_H */