Versioning:
===========
-U-Boot uses a 3 level version number containing a version, a
-sub-version, and a patchlevel: "U-Boot-2.34.5" means version "2",
-sub-version "34", and patchlevel "4".
+Starting with the release in October 2008, the names of the releases
+were changed from numerical release numbers without deeper meaning
+into a time stamp based numbering. Regular releases are identified by
+names consisting of the calendar year and month of the release date.
+Additional fields (if present) indicate release candidates or bug fix
+releases in "stable" maintenance trees.
-The patchlevel is used to indicate certain stages of development
-between released versions, i. e. officially released versions of
-U-Boot will always have a patchlevel of "0".
+Examples:
+ U-Boot v2009.11 - Release November 2009
+ U-Boot v2009.11.1 - Release 1 in version November 2009 stable tree
+ U-Boot v2010.09-rc1 - Release candiate 1 for September 2010 release
Directory Hierarchy:
CONFIG_SYS_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR
CONFIG_SYS_8272ADS - MPC8272ADS
+- Marvell Family Member
+ CONFIG_SYS_MVFS - define it if you want to enable
+ multiple fs option at one time
+ for marvell soc family
+
- MPC824X Family Member (if CONFIG_MPC824X is defined)
Define exactly one of
CONFIG_MPC8240, CONFIG_MPC8245
must be defined, to setup the maximum idle timeout for
the SMC.
-- Interrupt driven serial port input:
- CONFIG_SERIAL_SOFTWARE_FIFO
-
- PPC405GP only.
- Use an interrupt handler for receiving data on the
- serial port. It also enables using hardware handshake
- (RTS/CTS) and UART's built-in FIFO. Set the number of
- bytes the interrupt driven input buffer should have.
-
- Leave undefined to disable this feature, including
- disable the buffer and hardware handshake.
-
-- Console UART Number:
- CONFIG_UART1_CONSOLE
-
- AMCC PPC4xx only.
- If defined internal UART1 (and not UART0) is used
- as default U-Boot console.
-
- Boot Delay: CONFIG_BOOTDELAY - in seconds
Delay before automatically booting the default image;
set to -1 to disable autoboot.
(requires CONFIG_CMD_I2C)
CONFIG_CMD_SETGETDCR Support for DCR Register access
(4xx only)
- CONFIG_CMD_SHA1 print sha1 memory digest
+ CONFIG_CMD_SHA1SUM print sha1 memory digest
(requires CONFIG_CMD_MEMORY)
CONFIG_CMD_SOURCE "source" command Support
CONFIG_CMD_SPI * SPI serial bus support
CONFIG_PCA953X - use NXP's PCA953X series I2C GPIO
CONFIG_PCA953X_INFO - enable pca953x info command
+ The CONFIG_SYS_I2C_PCA953X_WIDTH option specifies a list of
+ chip-ngpio pairs that tell the PCA953X driver the number of
+ pins supported by a particular chip.
+
Note that if the GPIO device uses I2C, then the I2C interface
must also be configured. See I2C Support, below.
Define this to use i/o functions instead of macros
(some hardware wont work with macros)
+ CONFIG_FTGMAC100
+ Support for Faraday's FTGMAC100 Gigabit SoC Ethernet
+
+ CONFIG_FTGMAC100_EGIGA
+ Define this to use GE link update with gigabit PHY.
+ Define this if FTGMAC100 is connected to gigabit PHY.
+ If your system has 10/100 PHY only, it might not occur
+ wrong behavior. Because PHY usually return timeout or
+ useless data when polling gigabit status and gigabit
+ control registers. This behavior won't affect the
+ correctnessof 10/100 link speed update.
+
CONFIG_SMC911X
Support for SMSC's LAN911x and LAN921x chips
automatically converts one 32 bit word to two 16 bit
words you may also try CONFIG_SMC911X_32_BIT.
+ CONFIG_SH_ETHER
+ Support for Renesas on-chip Ethernet controller
+
+ CONFIG_SH_ETHER_USE_PORT
+ Define the number of ports to be used
+
+ CONFIG_SH_ETHER_PHY_ADDR
+ Define the ETH PHY's address
+
+ CONFIG_SH_ETHER_CACHE_WRITEBACK
+ If this option is set, the driver enables cache flush.
+
- USB Support:
At the moment only the UHCI host controller is
supported (PIP405, MIP405, MPC5200); define
SPI EEPROM, also an instance works with Crystal A/D and
D/As on the SACSng board)
+ CONFIG_SH_SPI
+
+ Enables the driver for SPI controller on SuperH. Currently
+ only SH7757 is supported.
+
CONFIG_SPI_X
Enables extended (16-bit) SPI EEPROM addressing.
ETX094, IVMS8, IVML24, SPD8xx, TQM8xxL,
HERMES, IP860, RPXlite, LWMON, LANTEC,
- PCU_E, FLAGADM, TQM8260
+ FLAGADM, TQM8260
- Error Recovery:
CONFIG_PANIC_HANG
- CONFIG_SYS_MONITOR_BASE:
Physical start address of boot monitor code (set by
make config files to be same as the text base address
- (TEXT_BASE) used when linking) - same as
+ (CONFIG_SYS_TEXT_BASE) used when linking) - same as
CONFIG_SYS_FLASH_BASE when booting from flash.
- CONFIG_SYS_MONITOR_LEN:
all data for the Linux kernel must be between "bootm_low"
and "bootm_low" + CONFIG_SYS_BOOTMAPSZ.
+- CONFIG_SYS_BOOT_RAMDISK_HIGH:
+ Enable initrd_high functionality. If defined then the
+ initrd_high feature is enabled and the bootm ramdisk subcommand
+ is enabled.
+
+- CONFIG_SYS_BOOT_GET_CMDLINE:
+ Enables allocating and saving kernel cmdline in space between
+ "bootm_low" and "bootm_low" + BOOTMAPSZ.
+
+- CONFIG_SYS_BOOT_GET_KBD:
+ Enables allocating and saving a kernel copy of the bd_info in
+ space between "bootm_low" and "bootm_low" + BOOTMAPSZ.
+
- CONFIG_SYS_MAX_FLASH_BANKS:
Max number of Flash memory banks
on high Ethernet traffic.
Defaults to 4 if not defined.
+- CONFIG_ENV_MAX_ENTRIES
+
+ Maximum number of entries in the hash table that is used
+ internally to store the environment settings. The default
+ setting is supposed to be generous and should work in most
+ cases. This setting can be used to tune behaviour; see
+ lib/hashtable.c for details.
+
The following definitions that deal with the placement and management
of environment data (variable area); in general, we support the
following configurations:
- CONFIG_ENV_SIZE:
These two #defines specify the offset and size of the environment
- area within the first NAND device.
+ area within the first NAND device. CONFIG_ENV_OFFSET must be
+ aligned to an erase block boundary.
- - CONFIG_ENV_OFFSET_REDUND
+ - CONFIG_ENV_OFFSET_REDUND (optional):
This setting describes a second storage area of CONFIG_ENV_SIZE
- size used to hold a redundant copy of the environment data,
- so that there is a valid backup copy in case there is a
- power failure during a "saveenv" operation.
+ size used to hold a redundant copy of the environment data, so
+ that there is a valid backup copy in case there is a power failure
+ during a "saveenv" operation. CONFIG_ENV_OFFSET_RENDUND must be
+ aligned to an erase block boundary.
+
+ - CONFIG_ENV_RANGE (optional):
+
+ Specifies the length of the region in which the environment
+ can be written. This should be a multiple of the NAND device's
+ block size. Specifying a range with more erase blocks than
+ are needed to hold CONFIG_ENV_SIZE allows bad blocks within
+ the range to be avoided.
+
+ - CONFIG_ENV_OFFSET_OOB (optional):
- Note: CONFIG_ENV_OFFSET and CONFIG_ENV_OFFSET_REDUND must be aligned
- to a block boundary, and CONFIG_ENV_SIZE must be a multiple of
- the NAND devices block size.
+ Enables support for dynamically retrieving the offset of the
+ environment from block zero's out-of-band data. The
+ "nand env.oob" command can be used to record this offset.
+ Currently, CONFIG_ENV_OFFSET_REDUND is not supported when
+ using CONFIG_ENV_OFFSET_OOB.
- CONFIG_NAND_ENV_DST
area defined by CONFIG_SYS_INIT_RAM_ADDR. Usually
CONFIG_SYS_GBL_DATA_OFFSET is chosen such that the initial
data is located at the end of the available space
- (sometimes written as (CONFIG_SYS_INIT_RAM_END -
+ (sometimes written as (CONFIG_SYS_INIT_RAM_SIZE -
CONFIG_SYS_INIT_DATA_SIZE), and the initial stack is just
below that area (growing from (CONFIG_SYS_INIT_RAM_ADDR +
CONFIG_SYS_GBL_DATA_OFFSET) downward.
Disable PCI-Express on systems where it is supported but not
required.
+- CONFIG_SYS_SRIO:
+ Chip has SRIO or not
+
+- CONFIG_SRIO1:
+ Board has SRIO 1 port available
+
+- CONFIG_SRIO2:
+ Board has SRIO 2 port available
+
+- CONFIG_SYS_SRIOn_MEM_VIRT:
+ Virtual Address of SRIO port 'n' memory region
+
+- CONFIG_SYS_SRIOn_MEM_PHYS:
+ Physical Address of SRIO port 'n' memory region
+
+- CONFIG_SYS_SRIOn_MEM_SIZE:
+ Size of SRIO port 'n' memory region
+
- CONFIG_SPD_EEPROM
Get DDR timing information from an I2C EEPROM. Common
with pluggable memory modules such as SODIMMs
globally (CONFIG_CMD_MEM).
- CONFIG_SKIP_LOWLEVEL_INIT
-- CONFIG_SKIP_RELOCATE_UBOOT
+ [ARM only] If this variable is defined, then certain
+ low level initializations (like setting up the memory
+ controller) are omitted and/or U-Boot does not
+ relocate itself into RAM.
- [ARM only] If these variables are defined, then
- certain low level initializations (like setting up
- the memory controller) are omitted and/or U-Boot does
- not relocate itself into RAM.
- Normally these variables MUST NOT be defined. The
- only exception is when U-Boot is loaded (to RAM) by
- some other boot loader or by a debugger which
- performs these initializations itself.
+ Normally this variable MUST NOT be defined. The only
+ exception is when U-Boot is loaded (to RAM) by some
+ other boot loader or by a debugger which performs
+ these initializations itself.
- CONFIG_PRELOADER
-
Modifies the behaviour of start.S when compiling a loader
that is executed before the actual U-Boot. E.g. when
compiling a NAND SPL.
interface is currently active. For example you
can do the following
- => setenv ethact FEC ETHERNET
- => ping 192.168.0.1 # traffic sent on FEC ETHERNET
- => setenv ethact SCC ETHERNET
- => ping 10.0.0.1 # traffic sent on SCC ETHERNET
+ => setenv ethact FEC
+ => ping 192.168.0.1 # traffic sent on FEC
+ => setenv ethact SCC
+ => ping 10.0.0.1 # traffic sent on SCC
ethrotate - When set to "no" U-Boot does not go through all
available network interfaces.
projects / people / ms / u-boot.git / blobdiff