CONFIG_CMD_MISC Misc functions like sleep etc
CONFIG_CMD_MMC * MMC memory mapped support
CONFIG_CMD_MII * MII utility commands
- CONFIG_CMD_NAND * NAND support
CONFIG_CMD_NET bootp, tftpboot, rarpboot
CONFIG_CMD_NFS NFS support
CONFIG_CMD_PCA953X * PCA953x I2C gpio commands
The clock frequency of the MII bus
- CONFIG_PHY_GIGE
-
- If this option is set, support for speed/duplex
- detection of gigabit PHY is included.
-
CONFIG_PHY_RESET_DELAY
Some PHY like Intel LXT971A need extra delay after
keep settings there always unmodified except somebody uses "saveenv"
to save the current settings.
-- CONFIG_ENV_IS_IN_DATAFLASH:
-
- Define this if you have a DataFlash memory device which you
- want to use for the environment.
-
- - CONFIG_ENV_OFFSET:
- - CONFIG_ENV_ADDR:
- - CONFIG_ENV_SIZE:
-
- These three #defines specify the offset and size of the
- environment area within the total memory of your DataFlash placed
- at the specified address.
-
-- CONFIG_ENV_IS_IN_SPI_FLASH:
-
- Define this if you have a SPI Flash memory device which you
- want to use for the environment.
-
- - CONFIG_ENV_OFFSET:
- - CONFIG_ENV_SIZE:
-
- These two #defines specify the offset and size of the
- environment area within the SPI Flash. CONFIG_ENV_OFFSET must be
- aligned to an erase sector boundary.
-
- - CONFIG_ENV_SECT_SIZE:
-
- Define the SPI flash's sector size.
-
- - CONFIG_ENV_OFFSET_REDUND (optional):
-
- This setting describes a second storage area of CONFIG_ENV_SIZE
- size used to hold a redundant copy of the environment data, so
- that there is a valid backup copy in case there is a power failure
- during a "saveenv" operation. CONFIG_ENV_OFFSET_REDUND must be
- aligned to an erase sector boundary.
-
- - CONFIG_ENV_SPI_BUS (optional):
- - CONFIG_ENV_SPI_CS (optional):
-
- Define the SPI bus and chip select. If not defined they will be 0.
-
- - CONFIG_ENV_SPI_MAX_HZ (optional):
-
- Define the SPI max work clock. If not defined then use 1MHz.
-
- - CONFIG_ENV_SPI_MODE (optional):
-
- Define the SPI work mode. If not defined then use SPI_MODE_3.
-
-- CONFIG_ENV_IS_IN_REMOTE:
-
- Define this if you have a remote memory space which you
- want to use for the local device's environment.
-
- - CONFIG_ENV_ADDR:
- - CONFIG_ENV_SIZE:
-
- These two #defines specify the address and size of the
- environment area within the remote memory space. The
- local device can get the environment from remote memory
- space by SRIO or PCIE links.
-
BE CAREFUL! For some special cases, the local device can not use
"saveenv" command. For example, the local device will get the
environment stored in a remote NOR flash by SRIO or PCIE link,
environment. If redundant environment is used, it will be copied to
CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE.
-- CONFIG_ENV_IS_IN_FAT:
- Define this if you want to use the FAT file system for the environment.
-
- - FAT_ENV_INTERFACE:
-
- Define this to a string that is the name of the block device.
-
- - FAT_ENV_DEVICE_AND_PART:
-
- Define this to a string to specify the partition of the device. It can
- be as following:
-
- "D:P", "D:0", "D", "D:" or "D:auto" (D, P are integers. And P >= 1)
- - "D:P": device D partition P. Error occurs if device D has no
- partition table.
- - "D:0": device D.
- - "D" or "D:": device D partition 1 if device D has partition
- table, or the whole device D if has no partition
- table.
- - "D:auto": first partition in device D with bootable flag set.
- If none, first valid partition in device D. If no
- partition table then means device D.
-
- - FAT_ENV_FILE:
-
- It's a string of the FAT file name. This file use to store the
- environment.
-
- - CONFIG_FAT_WRITE:
- This must be enabled. Otherwise it cannot save the environment file.
-
Please note that the environment is read-only until the monitor
has been relocated to RAM and a RAM copy of the environment has been
created; also, when using EEPROM you will have to use getenv_f()
projects / people / ms / u-boot.git / blobdiff