Convert CONFIG_VIDEO to Kconfig

[people/ms/u-boot.git] / README

diff --git a/README b/README
index 0a0d14ce2d7c180b9bae154188fdf05053c96100..4f9d29c032e20194eb0613ffb104179cec5f1510 100644 (file)
--- a/README
+++ b/README
@@ -813,11 +813,6 @@ The following options need to be configured:
                default i/o. Serial console can be forced with
                environment 'console=serial'.
 
-               When CONFIG_SILENT_CONSOLE is defined, all console
-               messages (by U-Boot and Linux!) can be silenced with
-               the "silent" environment variable. See
-               doc/README.silent for more information.
-
                CONFIG_SYS_CONSOLE_BG_COL: define the backgroundcolor, default
                        is 0x00.
                CONFIG_SYS_CONSOLE_FG_COL: define the foregroundcolor, default
@@ -837,23 +832,6 @@ The following options need to be configured:
                must be defined, to setup the maximum idle timeout for
                the SMC.
 
-- Pre-Console Buffer:
-               Prior to the console being initialised (i.e. serial UART
-               initialised etc) all console output is silently discarded.
-               Defining CONFIG_PRE_CONSOLE_BUFFER will cause U-Boot to
-               buffer any console messages prior to the console being
-               initialised to a buffer of size CONFIG_PRE_CON_BUF_SZ
-               bytes located at CONFIG_PRE_CON_BUF_ADDR. The buffer is
-               a circular buffer, so if more than CONFIG_PRE_CON_BUF_SZ
-               bytes are output before the console is initialised, the
-               earlier bytes are discarded.
-
-               Note that when printing the buffer a copy is made on the
-               stack so CONFIG_PRE_CON_BUF_SZ must fit on the stack.
-
-               'Sane' compilers will generate smaller code if
-               CONFIG_PRE_CON_BUF_SZ is a power of 2
-
 - Autoboot Command:
                CONFIG_BOOTCOMMAND
                Only needed when CONFIG_BOOTDELAY is enabled;
@@ -1361,7 +1339,7 @@ The following options need to be configured:
 
 - PWM Support:
                CONFIG_PWM_IMX
-               Support for PWM modul on the imx6.
+               Support for PWM module on the imx6.
 
 - TPM Support:
                CONFIG_TPM
@@ -1684,11 +1662,6 @@ CBFS (Coreboot Filesystem) support
                instead.
 
 - Video support:
-               CONFIG_VIDEO
-
-               Define this to enable video support (for output to
-               video).
-
                CONFIG_VIDEO_CT69000
 
                Enable Chips & Technologies 69000 Video chip
@@ -4487,7 +4460,7 @@ Low Level (hardware related) configuration options:
                CONFIG_SYS_GBL_DATA_OFFSET is chosen such that the initial
                data is located at the end of the available space
                (sometimes written as (CONFIG_SYS_INIT_RAM_SIZE -
-               CONFIG_SYS_INIT_DATA_SIZE), and the initial stack is just
+               GENERATED_GBL_DATA_SIZE), and the initial stack is just
                below that area (growing from (CONFIG_SYS_INIT_RAM_ADDR +
                CONFIG_SYS_GBL_DATA_OFFSET) downward.
 
@@ -4546,11 +4519,6 @@ Low Level (hardware related) configuration options:
                enable SPI microcode relocation patch (MPC8xx);
                define relocation offset in DPRAM [SCC4]
 
-- CONFIG_SYS_USE_OSCCLK:
-               Use OSCM clock mode on MBX8xx board. Be careful,
-               wrong setting might damage your board. Read
-               doc/README.MBX before setting this variable!
-
 - CONFIG_SYS_CPM_POST_WORD_ADDR: (MPC8xx, MPC8260 only)
                Offset of the bootmode word in DPRAM used by post
                (Power On Self Tests). This definition overrides