CONFIG_CMD_BOOTI * ARM64 Linux kernel Image support
CONFIG_CMD_CACHE * icache, dcache
CONFIG_CMD_CONSOLE coninfo
- CONFIG_CMD_CRC32 * crc32
CONFIG_CMD_DHCP * DHCP support
CONFIG_CMD_DIAG * Diagnostics
CONFIG_CMD_ECHO echo arguments
CONFIG_CMD_EDITENV edit env variable
CONFIG_CMD_ELF * bootelf, bootvx
- CONFIG_CMD_ENV_FLAGS * display details about env flags
CONFIG_CMD_ENV_EXISTS * check existence of env variable
CONFIG_CMD_EXPORTENV * export the environment
CONFIG_CMD_EXT2 * ext2 command support
that work for multiple fs types
CONFIG_CMD_FS_UUID * Look up a filesystem UUID
CONFIG_CMD_SAVEENV saveenv
- CONFIG_CMD_FDC * Floppy Disk Support
CONFIG_CMD_FAT * FAT command support
CONFIG_CMD_FLASH flinfo, erase, protect
CONFIG_CMD_FPGA FPGA device initialization support
- CONFIG_CMD_FUSE * Device fuse support
- CONFIG_CMD_GETTIME * Get time since boot
CONFIG_CMD_GO * the 'go' command (exec code)
CONFIG_CMD_GREPENV * search environment
- CONFIG_CMD_HASH * calculate hash / digest
CONFIG_CMD_I2C * I2C serial bus support
- CONFIG_CMD_IDE * IDE harddisk support
CONFIG_CMD_IMI iminfo
CONFIG_CMD_IMLS List all images found in NOR flash
CONFIG_CMD_IMLS_NAND * List all images found in NAND flash
- CONFIG_CMD_IMMAP * IMMR dump support
- CONFIG_CMD_IOTRACE * I/O tracing for debugging
CONFIG_CMD_IMPORTENV * import an environment
CONFIG_CMD_INI * import data from an ini file into the env
- CONFIG_CMD_IRQ * irqinfo
CONFIG_CMD_ITEST Integer/string test of 2 values
- CONFIG_CMD_JFFS2 * JFFS2 Support
- CONFIG_CMD_KGDB * kgdb
CONFIG_CMD_LDRINFO * ldrinfo (display Blackfin loader)
CONFIG_CMD_LINK_LOCAL * link-local IP address auto-configuration
(169.254.*.*)
CONFIG_CMD_SETGETDCR Support for DCR Register access
(4xx only)
CONFIG_CMD_SF * Read/write/erase SPI NOR flash
- CONFIG_CMD_SHA1SUM * print sha1 memory digest
- (requires CONFIG_CMD_MEMORY)
CONFIG_CMD_SOFTSWITCH * Soft switch setting command for BF60x
CONFIG_CMD_SOURCE "source" command Support
CONFIG_CMD_SPI * SPI serial bus support
disk/part_efi.c
CONFIG_MTD_PARTITIONS Memory Technology Device partition table.
- If IDE or SCSI support is enabled (CONFIG_CMD_IDE or
+ If IDE or SCSI support is enabled (CONFIG_IDE or
CONFIG_SCSI) you must configure support for at
least one non-MTD partition type as well.
the malloc area (as defined by CONFIG_SYS_MALLOC_LEN) should
be at least 4MB.
- CONFIG_LZMA
-
- If this option is set, support for lzma compressed
- images is included.
-
- Note: The LZMA algorithm adds between 2 and 4KB of code and it
- requires an amount of dynamic memory that is given by the
- formula:
-
- (1846 + 768 << (lc + lp)) * sizeof(uint16)
-
- Where lc and lp stand for, respectively, Literal context bits
- and Literal pos bits.
-
- This value is upper-bounded by 14MB in the worst case. Anyway,
- for a ~4MB large kernel image, we have lc=3 and lp=0 for a
- total amount of (1846 + 768 << (3 + 0)) * 2 = ~41KB... that is
- a very small buffer.
-
- Use the lzmainfo tool to determinate the lc and lp values and
- then calculate the amount of needed dynamic memory (ensuring
- the appropriate CONFIG_SYS_MALLOC_LEN value).
-
CONFIG_LZO
If this option is set, support for LZO compressed images
Specify the number of FPGA devices to support.
- CONFIG_CMD_FPGA_LOADMK
-
- Enable support for fpga loadmk command
-
- CONFIG_CMD_FPGA_LOADP
-
- Enable support for fpga loadp command - load partial bitstream
-
- CONFIG_CMD_FPGA_LOADBP
-
- Enable support for fpga loadbp command - load partial bitstream
- (Xilinx only)
-
CONFIG_SYS_FPGA_PROG_FEEDBACK
Enable printing of hash marks during FPGA configuration.
A better solution is to properly configure the firewall,
but sometimes that is not allowed.
-- Hashing support:
- CONFIG_CMD_HASH
-
- This enables a generic 'hash' command which can produce
- hashes / digests from a few algorithms (e.g. SHA1, SHA256).
-
- CONFIG_HASH_VERIFY
-
- Enable the hash verify command (hash -v). This adds to code
- size a little.
-
- Note: There is also a sha1sum command, which should perhaps
- be deprecated in favour of 'hash sha1'.
-
-- Freescale i.MX specific commands:
- CONFIG_CMD_HDMIDETECT
- This enables 'hdmidet' command which returns true if an
- HDMI monitor is detected. This command is i.MX 6 specific.
-
- bootcount support:
CONFIG_BOOTCOUNT_LIMIT
projects / people / ms / u-boot.git / blobdiff