Convert CONFIG_CMD_HDMIDETECT to Kconfig

[people/ms/u-boot.git] / README

diff --git a/README b/README
index 99af4c5bbf586f4d74c6d339f8eaadeb0fd53a7d..7abe2bc74bb01b7a8e5beff35021d74514d1441e 100644 (file)
--- a/README
+++ b/README
@@ -830,14 +830,9 @@ The following options need to be configured:
                CONFIG_CMD_CRC32        * crc32
                CONFIG_CMD_DHCP         * DHCP support
                CONFIG_CMD_DIAG         * Diagnostics
-               CONFIG_CMD_DTT          * Digital Therm and Thermostat
                CONFIG_CMD_ECHO           echo arguments
                CONFIG_CMD_EDITENV        edit env variable
-               CONFIG_CMD_EEPROM       * EEPROM read/write support
-               CONFIG_CMD_EEPROM_LAYOUT* EEPROM layout aware commands
                CONFIG_CMD_ELF          * bootelf, bootvx
-               CONFIG_CMD_ENV_CALLBACK * display details about env callbacks
-               CONFIG_CMD_ENV_FLAGS    * display details about env flags
                CONFIG_CMD_ENV_EXISTS   * check existence of env variable
                CONFIG_CMD_EXPORTENV    * export the environment
                CONFIG_CMD_EXT2         * ext2 command support
@@ -846,15 +841,11 @@ The following options need to be configured:
                                          that work for multiple fs types
                CONFIG_CMD_FS_UUID      * Look up a filesystem UUID
                CONFIG_CMD_SAVEENV        saveenv
-               CONFIG_CMD_FDC          * Floppy Disk Support
                CONFIG_CMD_FAT          * FAT command support
                CONFIG_CMD_FLASH          flinfo, erase, protect
                CONFIG_CMD_FPGA           FPGA device initialization support
-               CONFIG_CMD_FUSE         * Device fuse support
-               CONFIG_CMD_GETTIME      * Get time since boot
                CONFIG_CMD_GO           * the 'go' command (exec code)
                CONFIG_CMD_GREPENV      * search environment
-               CONFIG_CMD_HASH         * calculate hash / digest
                CONFIG_CMD_I2C          * I2C serial bus support
                CONFIG_CMD_IDE          * IDE harddisk support
                CONFIG_CMD_IMI            iminfo
@@ -2324,17 +2315,6 @@ The following options need to be configured:
                If defined, then this indicates the I2C bus number for the RTC.
                If not defined, then U-Boot assumes that RTC is on I2C bus 0.
 
-               CONFIG_SYS_DTT_BUS_NUM
-
-               If defined, then this indicates the I2C bus number for the DTT.
-               If not defined, then U-Boot assumes that DTT is on I2C bus 0.
-
-               CONFIG_SYS_I2C_DTT_ADDR:
-
-               If defined, specifies the I2C address of the DTT device.
-               If not defined, then U-Boot uses predefined value for
-               specified DTT device.
-
                CONFIG_SOFT_I2C_READ_REPEATED_START
 
                defining this will force the i2c_read() function in
@@ -2401,19 +2381,6 @@ The following options need to be configured:
 
                Specify the number of FPGA devices to support.
 
-               CONFIG_CMD_FPGA_LOADMK
-
-               Enable support for fpga loadmk command
-
-               CONFIG_CMD_FPGA_LOADP
-
-               Enable support for fpga loadp command - load partial bitstream
-
-               CONFIG_CMD_FPGA_LOADBP
-
-               Enable support for fpga loadbp command - load partial bitstream
-               (Xilinx only)
-
                CONFIG_SYS_FPGA_PROG_FEEDBACK
 
                Enable printing of hash marks during FPGA configuration.
@@ -2742,11 +2709,6 @@ The following options need to be configured:
                but sometimes that is not allowed.
 
 - Hashing support:
-               CONFIG_CMD_HASH
-
-               This enables a generic 'hash' command which can produce
-               hashes / digests from a few algorithms (e.g. SHA1, SHA256).
-
                CONFIG_HASH_VERIFY
 
                Enable the hash verify command (hash -v). This adds to code
@@ -2755,11 +2717,6 @@ The following options need to be configured:
                Note: There is also a sha1sum command, which should perhaps
                be deprecated in favour of 'hash sha1'.
 
-- Freescale i.MX specific commands:
-               CONFIG_CMD_HDMIDETECT
-               This enables 'hdmidet' command which returns true if an
-               HDMI monitor is detected.  This command is i.MX 6 specific.
-
 - bootcount support:
                CONFIG_BOOTCOUNT_LIMIT