- stack is optionally in SDRAM, if CONFIG_SPL_STACK_R is defined and
CONFIG_SPL_STACK_R_ADDR points into SDRAM
- preloader_console_init() can be called here - typically this is
- done by defining CONFIG_SPL_BOARD_INIT and then supplying a
+ done by selecting CONFIG_SPL_BOARD_INIT and then supplying a
spl_board_init() function containing this call
- loads U-Boot or (in falcon mode) Linux
CONFIG_CMD_CRC32 * crc32
CONFIG_CMD_DHCP * DHCP support
CONFIG_CMD_DIAG * Diagnostics
- CONFIG_CMD_DS4510 * ds4510 I2C gpio commands
- CONFIG_CMD_DS4510_INFO * ds4510 I2C info command
- CONFIG_CMD_DS4510_MEM * ds4510 I2C eeprom/sram commansd
- CONFIG_CMD_DS4510_RST * ds4510 I2C rst command
- CONFIG_CMD_DTT * Digital Therm and Thermostat
CONFIG_CMD_ECHO echo arguments
CONFIG_CMD_EDITENV edit env variable
CONFIG_CMD_EEPROM * EEPROM read/write support
If you do not have i2c muxes on your board, omit this define.
-----under removal:
-
-- Legacy I2C Support: CONFIG_SOFT_I2C
-
- NOTE: It is intended to move drivers to CONFIG_SYS_I2C which
- provides the following compelling advantages:
-
- - more than one i2c adapter is usable
- - approved multibus support
- - better i2c mux support
-
- ** CONFIG_SOFT_I2C is now being removed **
-
- With CONFIG_SOFT_I2C you will need to define
- CONFIG_SYS_I2C_SPEED to be the frequency (in Hz) at which you
- wish your i2c bus to run and CONFIG_SYS_I2C_SLAVE to be the
- address of this node (ie the CPU's i2c node address).
-
- Now, the u-boot i2c code for the mpc8xx
- (arch/powerpc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node
- and so its address should therefore be cleared to 0 (See,
- eg, MPC823e User's Manual p.16-473). So, set
- CONFIG_SYS_I2C_SLAVE to 0.
-
- When a board is reset during an i2c bus transfer
- chips might think that the current transfer is still
- in progress. Reset the slave devices by sending start
- commands until the slave device responds.
-
- That's all that's required for CONFIG_HARD_I2C.
-
+- Legacy I2C Support:
If you use the software i2c interface (CONFIG_SYS_I2C_SOFT)
then the following macros need to be defined (examples are
from include/configs/lwmon.h):
custom i2c_init_board() routine in boards/xxx/board.c
is run early in the boot sequence.
- CONFIG_SYS_I2C_BOARD_LATE_INIT
-
- An alternative to CONFIG_SYS_I2C_INIT_BOARD. If this option is
- defined a custom i2c_board_late_init() routine in
- boards/xxx/board.c is run AFTER the operations in i2c_init()
- is completed. This callpoint can be used to unreset i2c bus
- using CPU i2c controller register accesses for CPUs whose i2c
- controller provide such a method. It is called at the end of
- i2c_init() to allow i2c_init operations to setup the i2c bus
- controller on the CPU (e.g. setting bus speed & slave address).
-
- CONFIG_I2CFAST (PPC405GP|PPC405EP only)
-
- This option enables configuration of bi_iic_fast[] flags
- in u-boot bd_info structure based on u-boot environment
- variable "i2cfast". (see also i2cfast)
-
CONFIG_I2C_MULTI_BUS
This option allows the use of multiple I2C buses, each of which
If defined, then this indicates the I2C bus number for the RTC.
If not defined, then U-Boot assumes that RTC is on I2C bus 0.
- CONFIG_SYS_DTT_BUS_NUM
-
- If defined, then this indicates the I2C bus number for the DTT.
- If not defined, then U-Boot assumes that DTT is on I2C bus 0.
-
- CONFIG_SYS_I2C_DTT_ADDR:
-
- If defined, specifies the I2C address of the DTT device.
- If not defined, then U-Boot uses predefined value for
- specified DTT device.
-
CONFIG_SOFT_I2C_READ_REPEATED_START
defining this will force the i2c_read() function in
Enable the hash verify command (hash -v). This adds to code
size a little.
- CONFIG_SHA1 - This option enables support of hashing using SHA1
- algorithm. The hash is calculated in software.
- CONFIG_SHA256 - This option enables support of hashing using
- SHA256 algorithm. The hash is calculated in software.
- CONFIG_SHA_HW_ACCEL - This option enables hardware acceleration
- for SHA1/SHA256 hashing.
- This affects the 'hash' command and also the
- hash_lookup_algo() function.
- CONFIG_SHA_PROG_HW_ACCEL - This option enables
- hardware-acceleration for SHA1/SHA256 progressive hashing.
- Data can be streamed in a block at a time and the hashing
- is performed in hardware.
-
Note: There is also a sha1sum command, which should perhaps
be deprecated in favour of 'hash sha1'.
This define is introduced, as the legacy image format is
enabled per default for backward compatibility.
-- FIT image support:
- CONFIG_FIT_DISABLE_SHA256
- Supporting SHA256 hashes has quite an impact on binary size.
- For constrained systems sha256 hash support can be disabled
- with this option.
-
- TODO(sjg@chromium.org): Adjust this option to be positive,
- and move it to Kconfig
-
- Standalone program support:
CONFIG_STANDALONE_LOAD_ADDR
If defined, don't allow the -f switch to env set override variable
access flags.
-- CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC (OMAP only)
- This is set by OMAP boards for the max time that reset should
- be asserted. See doc/README.omap-reset-time for details on how
- the value can be calculated on a given board.
-
- CONFIG_USE_STDINT
If stdint.h is available with your toolchain you can define this
option to enable it. You can provide option 'USE_STDINT=1' when
projects / people / ms / u-boot.git / blobdiff