Kconfig: spl: Add SPL support options to Kconfig

[people/ms/u-boot.git] / README

diff --git a/README b/README
index f41a6afc341d985cc824b262d8ffbecd1b7f8845..d916ee77f59486fc65a6ef515aaeab33b498cf73 100644 (file)
--- a/README
+++ b/README
@@ -3509,21 +3509,6 @@ FIT uImage format:
                CONFIG_SPL_INIT_MINIMAL
                Arch init code should be built for a very small image
 
-               CONFIG_SPL_LIBCOMMON_SUPPORT
-               Support for common/libcommon.o in SPL binary
-
-               CONFIG_SPL_LIBDISK_SUPPORT
-               Support for disk/libdisk.o in SPL binary
-
-               CONFIG_SPL_I2C_SUPPORT
-               Support for drivers/i2c/libi2c.o in SPL binary
-
-               CONFIG_SPL_GPIO_SUPPORT
-               Support for drivers/gpio/libgpio.o in SPL binary
-
-               CONFIG_SPL_MMC_SUPPORT
-               Support for drivers/mmc/libmmc.o in SPL binary
-
                CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR,
                CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS,
                Address and partition on the MMC to load U-Boot from
@@ -3547,12 +3532,6 @@ FIT uImage format:
                Partition on the MMC to load U-Boot from when the MMC is being
                used in fs mode
 
-               CONFIG_SPL_FAT_SUPPORT
-               Support for fs/fat/libfat.o in SPL binary
-
-               CONFIG_SPL_EXT_SUPPORT
-               Support for EXT filesystem in SPL binary
-
                CONFIG_SPL_FS_LOAD_PAYLOAD_NAME
                Filename to read to load U-Boot when reading from filesystem
 
@@ -3591,18 +3570,10 @@ FIT uImage format:
                Support for a lightweight UBI (fastmap) scanner and
                loader
 
-               CONFIG_SPL_MTD_SUPPORT
-               Support for the MTD subsystem within SPL.  Useful for
-               environment on NAND support within SPL.
-
                CONFIG_SPL_NAND_RAW_ONLY
                Support to boot only raw u-boot.bin images. Use this only
                if you need to save space.
 
-               CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
-               Set for the SPL on PPC mpc8xxx targets, support for
-               drivers/ddr/fsl/libddr.o in SPL binary.
-
                CONFIG_SPL_COMMON_INIT_DDR
                Set for common ddr init with serial presence detect in
                SPL binary.
@@ -3638,29 +3609,9 @@ FIT uImage format:
                Support for an OMAP3-specific set of functions to return the
                ID and MFR of the first attached NAND chip, if present.
 
-               CONFIG_SPL_SERIAL_SUPPORT
-               Support for drivers/serial/libserial.o in SPL binary
-
-               CONFIG_SPL_SPI_FLASH_SUPPORT
-               Support for drivers/mtd/spi/libspi_flash.o in SPL binary
-
-               CONFIG_SPL_SPI_SUPPORT
-               Support for drivers/spi/libspi.o in SPL binary
-
                CONFIG_SPL_RAM_DEVICE
                Support for running image already present in ram, in SPL binary
 
-               CONFIG_SPL_LIBGENERIC_SUPPORT
-               Support for lib/libgeneric.o in SPL binary
-
-               CONFIG_SPL_ENV_SUPPORT
-               Support for the environment operating in SPL binary
-
-               CONFIG_SPL_NET_SUPPORT
-               Support for the net/libnet.o in SPL binary.
-               It conflicts with SPL env from storage medium specified by
-               CONFIG_ENV_IS_xxx but CONFIG_ENV_IS_NOWHERE
-
                CONFIG_SPL_PAD_TO
                Image offset to which the SPL should be padded before appending
                the SPL payload. By default, this is defined as