imx: hab: Check if CSF contains deprecated commands

[people/ms/u-boot.git] / README

diff --git a/README b/README
index b055ae7ef29c71ca65917f0f5858e58308fec419..fabd532623924bbdf1a32d471b8862e5e5c2e36c 100644 (file)
--- a/README
+++ b/README
@@ -714,11 +714,6 @@ The following options need to be configured:
                RAM and NFS.
 
 - Bootcount:
-               CONFIG_BOOTCOUNT_LIMIT
-               Implements a mechanism for detecting a repeating reboot
-               cycle, see:
-               http://www.denx.de/wiki/view/DULG/UBootBootCountLimit
-
                CONFIG_BOOTCOUNT_ENV
                If no softreset save registers are found on the hardware
                "bootcount" is stored in the environment. To prevent a
@@ -2001,11 +1996,6 @@ The following options need to be configured:
                SPI EEPROM, also an instance works with Crystal A/D and
                D/As on the SACSng board)
 
-               CONFIG_SH_SPI
-
-               Enables the driver for SPI controller on SuperH. Currently
-               only SH7757 is supported.
-
                CONFIG_SOFT_SPI
 
                Enables a software (bit-bang) SPI driver rather than
@@ -2024,11 +2014,6 @@ The following options need to be configured:
                Currently supported on some MPC8xxx processors.  For an
                example, see include/configs/mpc8349emds.h.
 
-               CONFIG_MXC_SPI
-
-               Enables the driver for the SPI controllers on i.MX and MXC
-               SoCs. Currently i.MX31/35/51 are supported.
-
                CONFIG_SYS_SPI_MXC_WAIT
                Timeout for waiting until spi transfer completed.
                default: (CONFIG_SYS_HZ/100)     /* 10 ms */
@@ -2311,18 +2296,6 @@ The following options need to be configured:
                CONFIG_SF_DEFAULT_MODE          (see include/spi.h)
                CONFIG_SF_DEFAULT_SPEED         in Hz
 
-               CONFIG_SYSTEMACE
-
-               Adding this option adds support for Xilinx SystemACE
-               chips attached via some sort of local bus. The address
-               of the chip must also be defined in the
-               CONFIG_SYS_SYSTEMACE_BASE macro. For example:
-
-               #define CONFIG_SYSTEMACE
-               #define CONFIG_SYS_SYSTEMACE_BASE 0xf0000000
-
-               When SystemACE support is added, the "ace" device type
-               becomes available to the fat commands, i.e. fatls.
 
 - TFTP Fixed UDP Port:
                CONFIG_TFTP_PORT
@@ -2345,11 +2318,6 @@ The following options need to be configured:
                but sometimes that is not allowed.
 
 - bootcount support:
-               CONFIG_BOOTCOUNT_LIMIT
-
-               This enables the bootcounter support, see:
-               http://www.denx.de/wiki/DULG/UBootBootCountLimit
-
                CONFIG_AT91SAM9XE
                enable special bootcounter support on at91sam9xe based boards.
                CONFIG_SOC_DA8XX
@@ -2726,11 +2694,6 @@ FIT uImage format:
                CONFIG_SYS_SPL_MALLOC_SIZE
                The size of the malloc pool used in SPL.
 
-               CONFIG_SPL_FRAMEWORK
-               Enable the SPL framework under common/.  This framework
-               supports MMC, NAND and YMODEM loading of U-Boot and NAND
-               NAND loading of the Linux Kernel.
-
                CONFIG_SPL_OS_BOOT
                Enable booting directly to an OS from SPL.
                See also: doc/README.falcon