compatible = "tsd,rk3399-q7", "tsd,puma", "rockchip,rk3399";
config {
- u-boot,spl-payload-offset = <0x40000>; /* 256kbyte */
+ u-boot,spl-payload-offset = <0x40000>; /* @ 256KB */
+ u-boot,mmc-env-offset = <0x4000>; /* @ 16KB */
+ u-boot,efi-partition-entries-offset = <0x200000>; /* 2MB */
u-boot,boot-led = "module_led";
};
chosen {
stdout-path = "serial0:115200n8";
- u-boot,spl-boot-order = &spiflash, &sdhci, &sdmmc;
+ u-boot,spl-boot-order = \
+ "same-as-spl", &spiflash, &sdhci, &sdmmc;
};
aliases {
module_led {
label = "module_led";
- gpios = <&gpio2 25 GPIO_ACTIVE_HIGH>;
+ gpios = <&gpio2 RK_PD1 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
sd_card_led {
label = "sd_card_led";
- gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+ gpios = <&gpio1 RK_PA2 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "mmc0";
};
};
};
};
+ usbhub_enable: usbhub_enable {
+ compatible = "regulator-fixed";
+ regulator-name = "usbhub_enable";
+ enable-active-low;
+ gpio = <&gpio4 RK_PA3 GPIO_ACTIVE_LOW>;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ /*
+ * The Qseven BIOS_DISABLE signal on the RK3399-Q7 keeps the on-module
+ * eMMC and SPI flash powered-down initially (in fact it keeps the
+ * reset signal asserted). Even though it is an enable signal, we
+ * model this as a regulator.
+ */
+ bios_enable: bios_enable {
+ compatible = "regulator-fixed";
+ u-boot,dm-pre-reloc;
+ regulator-name = "bios_enable";
+ enable-active-high;
+ gpio = <&gpio3 RK_PD5 GPIO_ACTIVE_LOW>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
vccadc_ref: vccadc-ref {
compatible = "regulator-fixed";
regulator-name = "vcc1v8_sys";
vcc5v0_otg: vcc5v0-otg-regulator {
compatible = "regulator-fixed";
enable-active-high;
- gpio = <&gpio0 2 GPIO_ACTIVE_HIGH>;
+ gpio = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&otg_vbus_drv>;
regulator-name = "vcc5v0_otg";
vcc5v0_host: vcc5v0-host-regulator {
compatible = "regulator-fixed";
enable-active-low;
- gpio = <&gpio4 3 GPIO_ACTIVE_HIGH>;
+ gpio = <&gpio4 RK_PA3 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&host_vbus_drv>;
regulator-name = "vcc5v0_host";
phy-supply = <&vcc_phy>;
phy-mode = "rgmii";
clock_in_out = "input";
- snps,reset-gpio = <&gpio3 16 GPIO_ACTIVE_LOW>;
+ snps,reset-gpio = <&gpio3 RK_PC0 GPIO_ACTIVE_LOW>;
snps,reset-active-low;
snps,reset-delays-us = <2 10000 50000>;
assigned-clocks = <&cru SCLK_RMII_SRC>;
vdd_gpu: fan535555@60 {
compatible = "fcs,fan53555";
reg = <0x60>;
- vsel-gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+ vsel-gpios = <&gpio1 RK_PB6 GPIO_ACTIVE_HIGH>;
vin-supply = <&vcc5v0_sys>;
regulator-compatible = "fan53555-reg";
regulator-name = "vdd_gpu";
vdd_cpu_b: fan53555@60 {
compatible = "fcs,fan53555";
reg = <0x60>;
- vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+ vsel-gpios = <&gpio1 RK_PA4 GPIO_ACTIVE_HIGH>;
vin-supply = <&vcc5v0_sys>;
regulator-compatible = "fan53555-reg";
regulator-name = "vdd_cpu_b";
assigned-clocks = <&cru SCLK_PCIEPHY_REF>;
assigned-clock-parents = <&cru SCLK_PCIEPHY_REF100M>;
assigned-clock-rates = <100000000>;
- ep-gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
+ ep-gpios = <&gpio4 RK_PC6 GPIO_ACTIVE_HIGH>;
num-lanes = <4>;
pinctrl-names = "default";
pinctrl-0 = <&pcie_clkreqn>;
};
&pcie_phy {
- status = "okay";
+ status = "okay";
};
&pmu_io_domains {
};
&sdmmc {
- u-boot,dm-pre-reloc;
+ u-boot,dm-pre-reloc;
clock-frequency = <150000000>;
clock-freq-min-max = <100000 150000000>;
supports-sd;
};
&usb_host0_ehci {
- status = "okay";
+ status = "disabled";
};
&usb_host0_ohci {
- status = "okay";
+ status = "disabled";
};
&dwc3_typec0 {
- status = "disabled";
+ status = "okay";
};
&usb_host1_ehci {
- status = "okay";
+ status = "disabled";
};
&usb_host1_ohci {
- status = "okay";
+ status = "disabled";
};
&dwc3_typec1 {
- rockchip,vbus-gpio = <&gpio4 3 GPIO_ACTIVE_LOW>;
status = "okay";
};
status = "okay";
};
+&gpio3 {
+ u-boot,dm-pre-reloc;
+};
+
&pinctrl {
/* Pins that are not explicitely used by any devices */
pinctrl-names = "default";
pinctrl-0 = <&puma_pin_hog>;
+
hog {
puma_pin_hog: puma_pin_hog {
rockchip,pins =
/* We need pull-ups on Q7 buttons */
- <0 4 RK_FUNC_GPIO &pcfg_pull_up>, /* LID_BTN# */
- <0 10 RK_FUNC_GPIO &pcfg_pull_up>, /* BATLOW# */
- <0 11 RK_FUNC_GPIO &pcfg_pull_up>, /* SLP_BTN# */
- <0 9 RK_FUNC_GPIO &pcfg_pull_up>; /* BIOS_DISABLE# */
+ <RK_GPIO0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>, /* LID_BTN# */
+ <RK_GPIO0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>, /* BATLOW# */
+ <RK_GPIO0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_up>, /* SLP_BTN# */
+ <RK_GPIO0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_up>; /* BIOS_DISABLE# */
};
};
pmic {
pmic_int_l: pmic-int-l {
rockchip,pins =
- <1 22 RK_FUNC_GPIO &pcfg_pull_up>;
+ <RK_GPIO1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
leds_pins_puma: led_pins@0 {
rockchip,pins =
- <2 25 RK_FUNC_GPIO &pcfg_pull_none>,
- <1 2 RK_FUNC_GPIO &pcfg_pull_none>;
+ <RK_GPIO2 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>,
+ <RK_GPIO1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
};
usb2 {
otg_vbus_drv: otg-vbus-drv {
rockchip,pins =
- <0 2 RK_FUNC_GPIO &pcfg_pull_none>;
+ <RK_GPIO0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
};
host_vbus_drv: host-vbus-drv {
rockchip,pins =
- <0 2 RK_FUNC_GPIO &pcfg_pull_none>;
+ <RK_GPIO4 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
i2c8 {
i2c8_xfer_a: i2c8-xfer {
- rockchip,pins = <1 21 RK_FUNC_1 &pcfg_pull_up>,
- <1 20 RK_FUNC_1 &pcfg_pull_up>;
+ rockchip,pins =
+ <RK_GPIO1 RK_PC5 RK_FUNC_1 &pcfg_pull_up>,
+ <RK_GPIO1 RK_PC4 RK_FUNC_1 &pcfg_pull_up>;
};
};
};
&i2c6_xfer {
/* Enable pull-ups, the pins would float otherwise. */
rockchip,pins =
- <2 10 RK_FUNC_2 &pcfg_pull_up>,
- <2 9 RK_FUNC_2 &pcfg_pull_up>;
+ <RK_GPIO2 RK_PB2 RK_FUNC_2 &pcfg_pull_up>,
+ <RK_GPIO2 RK_PB1 RK_FUNC_2 &pcfg_pull_up>;
};
&i2c7 {
&spi5 {
status = "okay";
};
-