#include <debug_uart.h>
#include <dm.h>
#include <fdtdec.h>
+#include <i2c.h>
#include <led.h>
#include <malloc.h>
#include <ram.h>
#include <spl.h>
#include <asm/gpio.h>
#include <asm/io.h>
+#include <asm/arch/bootrom.h>
#include <asm/arch/clock.h>
#include <asm/arch/hardware.h>
#include <asm/arch/periph.h>
+#include <asm/arch/pmu_rk3288.h>
#include <asm/arch/sdram.h>
+#include <asm/arch/sdram_common.h>
+#include <asm/arch/sys_proto.h>
#include <asm/arch/timer.h>
#include <dm/pinctrl.h>
#include <dm/root.h>
#include <dm/test.h>
#include <dm/util.h>
#include <power/regulator.h>
+#include <power/rk8xx_pmic.h>
DECLARE_GLOBAL_DATA_PTR;
}
fallback:
+#elif defined(CONFIG_TARGET_CHROMEBOOK_JERRY) || \
+ defined(CONFIG_TARGET_CHROMEBIT_MICKEY) || \
+ defined(CONFIG_TARGET_CHROMEBOOK_MINNIE)
+ return BOOT_DEVICE_SPI;
#endif
return BOOT_DEVICE_MMC1;
}
-u32 spl_boot_mode(const u32 boot_device)
-{
- return MMCSD_MODE_RAW;
-}
-
-/* read L2 control register (L2CTLR) */
-static inline uint32_t read_l2ctlr(void)
-{
- uint32_t val = 0;
-
- asm volatile ("mrc p15, 1, %0, c9, c0, 2" : "=r" (val));
-
- return val;
-}
-
-/* write L2 control register (L2CTLR) */
-static inline void write_l2ctlr(uint32_t val)
-{
- /*
- * Note: L2CTLR can only be written when the L2 memory system
- * is idle, ie before the MMU is enabled.
- */
- asm volatile("mcr p15, 1, %0, c9, c0, 2" : : "r" (val) : "memory");
- isb();
-}
-
-static void configure_l2ctlr(void)
-{
- uint32_t l2ctlr;
-
- l2ctlr = read_l2ctlr();
- l2ctlr &= 0xfffc0000; /* clear bit0~bit17 */
-
- /*
- * Data RAM write latency: 2 cycles
- * Data RAM read latency: 2 cycles
- * Data RAM setup latency: 1 cycle
- * Tag RAM write latency: 1 cycle
- * Tag RAM read latency: 1 cycle
- * Tag RAM setup latency: 1 cycle
- */
- l2ctlr |= (1 << 3 | 1 << 0);
- write_l2ctlr(l2ctlr);
-}
-
#ifdef CONFIG_SPL_MMC_SUPPORT
static int configure_emmc(struct udevice *pinctrl)
{
+#if defined(CONFIG_TARGET_CHROMEBOOK_JERRY)
+
struct gpio_desc desc;
int ret;
debug("gpio value ret=%d\n", ret);
return ret;
}
+#endif
+ return 0;
+}
+#endif
+
+#if !defined(CONFIG_SPL_OF_PLATDATA)
+static int phycore_init(void)
+{
+ struct udevice *pmic;
+ int ret;
+
+ ret = uclass_first_device_err(UCLASS_PMIC, &pmic);
+ if (ret)
+ return ret;
+
+#if defined(CONFIG_SPL_POWER_SUPPORT)
+ /* Increase USB input current to 2A */
+ ret = rk818_spl_configure_usb_input_current(pmic, 2000);
+ if (ret)
+ return ret;
+
+ /* Close charger when USB lower then 3.26V */
+ ret = rk818_spl_configure_usb_chrg_shutdown(pmic, 3260000);
+ if (ret)
+ return ret;
+#endif
return 0;
}
#endif
-extern void back_to_bootrom(void);
+
void board_init_f(ulong dummy)
{
struct udevice *pinctrl;
int ret;
/* Example code showing how to enable the debug UART on RK3288 */
-#ifdef EARLY_UART
#include <asm/arch/grf_rk3288.h>
/* Enable early UART on the RK3288 */
#define GRF_BASE 0xff770000
* printascii("string");
*/
debug_uart_init();
-#endif
-
- ret = spl_init();
+ debug("\nspl:debug uart enabled in %s\n", __func__);
+ ret = spl_early_init();
if (ret) {
- debug("spl_init() failed: %d\n", ret);
+ debug("spl_early_init() failed: %d\n", ret);
hang();
}
rockchip_timer_init();
configure_l2ctlr();
- ret = uclass_get_device(UCLASS_CLK, 0, &dev);
+ ret = rockchip_get_clk(&dev);
if (ret) {
debug("CLK init failed: %d\n", ret);
return;
return;
}
+#if !defined(CONFIG_SPL_OF_PLATDATA)
+ if (of_machine_is_compatible("phytec,rk3288-phycore-som")) {
+ ret = phycore_init();
+ if (ret) {
+ debug("Failed to set up phycore power settings: %d\n",
+ ret);
+ return;
+ }
+ }
+#endif
+
+#if !defined(CONFIG_SUPPORT_TPL)
+ debug("\nspl:init dram\n");
ret = uclass_get_device(UCLASS_RAM, 0, &dev);
if (ret) {
debug("DRAM init failed: %d\n", ret);
return;
}
-#ifdef CONFIG_ROCKCHIP_SPL_BACK_TO_BROM
- back_to_bootrom();
+#endif
+
+#if CONFIG_IS_ENABLED(ROCKCHIP_BACK_TO_BROM) && !defined(CONFIG_SPL_BOARD_INIT)
+ back_to_bootrom(BROM_BOOT_NEXTSTAGE);
#endif
}
debug("%s: Cannot find pinctrl device\n", __func__);
goto err;
}
+
#ifdef CONFIG_SPL_MMC_SUPPORT
- if (!IS_ENABLED(CONFIG_TARGET_ROCK2) &&
- !IS_ENABLED(CONFIG_TARGET_FIREFLY_RK3288)) {
- ret = pinctrl_request_noflags(pinctrl, PERIPH_ID_SDCARD);
- if (ret) {
- debug("%s: Failed to set up SD card\n", __func__);
- goto err;
- }
- ret = configure_emmc(pinctrl);
- if (ret) {
- debug("%s: Failed to set up eMMC\n", __func__);
- goto err;
- }
+ ret = pinctrl_request_noflags(pinctrl, PERIPH_ID_SDCARD);
+ if (ret) {
+ debug("%s: Failed to set up SD card\n", __func__);
+ goto err;
+ }
+ ret = configure_emmc(pinctrl);
+ if (ret) {
+ debug("%s: Failed to set up eMMC\n", __func__);
+ goto err;
}
#endif
}
preloader_console_init();
+#if CONFIG_IS_ENABLED(ROCKCHIP_BACK_TO_BROM)
+ back_to_bootrom(BROM_BOOT_NEXTSTAGE);
+#endif
return;
err:
printf("spl_board_init: Error %d\n", ret);
hang();
}
-void lowlevel_init(void)
+#ifdef CONFIG_SPL_OS_BOOT
+
+#define PMU_BASE 0xff730000
+int dram_init_banksize(void)
{
+ struct rk3288_pmu *const pmu = (void *)PMU_BASE;
+ size_t size = rockchip_sdram_size((phys_addr_t)&pmu->sys_reg[2]);
+
+ gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+ gd->bd->bi_dram[0].size = size;
+
+ return 0;
}
+#endif
projects / people / ms / u-boot.git / blobdiff