da830evm: Add support for TI EMAC

[people/ms/u-boot.git] / board / davinci / da830evm / da830evm.c

diff --git a/board/davinci/da830evm/da830evm.c b/board/davinci/da830evm/da830evm.c
index aac5c5cbe1a51ec0b7495f2604702f3a97cd5597..ed668afccc87c32ad0df034b19a9912b67257264 100644 (file)
--- a/board/davinci/da830evm/da830evm.c
+++ b/board/davinci/da830evm/da830evm.c
@@ -34,8 +34,11 @@
 
 #include <common.h>
 #include <i2c.h>
+#include <net.h>
+#include <netdev.h>
 #include <asm/arch/hardware.h>
 #include <asm/arch/emif_defs.h>
+#include <asm/arch/emac_defs.h>
 #include <asm/io.h>
 #include "../common/misc.h"
 
@@ -69,6 +72,20 @@ static const struct pinmux_config emifa_nand_pins[] = {
        { pinmux[18], 1, 5 },
 };
 
+/* EMAC PHY interface pins */
+static const struct pinmux_config emac_pins[] = {
+       { pinmux[9], 0, 5 },
+       { pinmux[10], 2, 1 },
+       { pinmux[10], 2, 2 },
+       { pinmux[10], 2, 3 },
+       { pinmux[10], 2, 4 },
+       { pinmux[10], 2, 5 },
+       { pinmux[10], 2, 6 },
+       { pinmux[10], 2, 7 },
+       { pinmux[11], 2, 0 },
+       { pinmux[11], 2, 1 },
+};
+
 /* UART pin muxer settings */
 static const struct pinmux_config uart_pins[] = {
        { pinmux[8], 2, 7 },
@@ -77,8 +94,8 @@ static const struct pinmux_config uart_pins[] = {
 
 /* I2C pin muxer settings */
 static const struct pinmux_config i2c_pins[] = {
-       { pinmux[9], 2, 3 },
-       { pinmux[9], 2, 4 }
+       { pinmux[8], 2, 3 },
+       { pinmux[8], 2, 4 }
 };
 
 /* USB0_DRVVBUS pin muxer settings */
@@ -98,6 +115,9 @@ static const struct pinmux_resource pinmuxes[] = {
 #ifdef CONFIG_USE_NAND
        PINMUX_ITEM(emifa_nand_pins),
 #endif
+#if defined(CONFIG_DRIVER_TI_EMAC)
+       PINMUX_ITEM(emac_pins),
+#endif
 };
 
 int board_init(void)
@@ -169,3 +189,44 @@ int board_init(void)
 
        return(0);
 }
+
+#if defined(CONFIG_DRIVER_TI_EMAC)
+
+#define PHY_SW_I2C_ADDR        0x5f /* Address of PHY on i2c bus */
+
+/*
+ * Initializes on-board ethernet controllers.
+ */
+int board_eth_init(bd_t *bis)
+{
+       u_int8_t mac_addr[6];
+       u_int8_t switch_start_cmd[2] = { 0x01, 0x23 };
+
+       /* Read Ethernet MAC address from EEPROM */
+       if (dvevm_read_mac_address(mac_addr))
+               /* set address env if not already set */
+               dv_configure_mac_address(mac_addr);
+
+       /* read the address back from env */
+       if (!eth_getenv_enetaddr("ethaddr", mac_addr))
+               return -1;
+
+       /* provide the resulting addr to the driver */
+       davinci_eth_set_mac_addr(mac_addr);
+
+       /* enable the Ethernet switch in the 3 port PHY */
+       if (i2c_write(PHY_SW_I2C_ADDR, 0, 0,
+                       switch_start_cmd, sizeof(switch_start_cmd))) {
+               printf("Ethernet switch start failed!\n");
+               return -1;
+       }
+
+       /* finally, initialise the driver */
+       if (!davinci_emac_initialize()) {
+               printf("Error: Ethernet init failed!\n");
+               return -1;
+       }
+
+       return 0;
+}
+#endif /* CONFIG_DRIVER_TI_EMAC */