if USB_GADGET
+config USB_GADGET_MANUFACTURER
+ string "Vendor name of the USB device"
+ default "Allwinner Technology" if ARCH_SUNXI
+ default "U-Boot"
+ help
+ Vendor name of the USB device emulated, reported to the host device.
+ This is usually either the manufacturer of the device or the SoC.
+
+config USB_GADGET_VENDOR_NUM
+ hex "Vendor ID of the USB device"
+ default 0x1f3a if ARCH_SUNXI
+ default 0x0
+ help
+ Vendor ID of the USB device emulated, reported to the host device.
+ This is usually the board or SoC vendor's, unless you've registered
+ for one.
+
+config USB_GADGET_PRODUCT_NUM
+ hex "Product ID of the USB device"
+ default 0x1010 if ARCH_SUNXI
+ default 0x0
+ help
+ Product ID of the USB device emulated, reported to the host device.
+
config USB_GADGET_ATMEL_USBA
bool "Atmel USBA"
select USB_GADGET_DUALSPEED
USBA is the integrated high-speed USB Device controller on
the AT32AP700x, some AT91SAM9 and AT91CAP9 processors from Atmel.
+config USB_GADGET_BCM_UDC_OTG_PHY
+ bool "Broadcom UDC OTG PHY"
+ help
+ Enable the Broadcom UDC OTG physical device interface.
+
config USB_GADGET_DWC2_OTG
bool "DesignWare USB2.0 HS OTG controller (gadget mode)"
select USB_GADGET_DUALSPEED
driver to operate in Peripheral mode. This option requires
USB_GADGET to be enabled.
+if USB_GADGET_DWC2_OTG
+
+config USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8
+ bool "DesignWare USB2.0 HS OTG controller 8-bit PHY bus width"
+ help
+ Set the Designware USB2.0 high-speed OTG controller
+ PHY interface width to 8 bits, rather than the default (16 bits).
+
+endif # USB_GADGET_DWC2_OTG
+
config CI_UDC
bool "ChipIdea device controller"
select USB_GADGET_DUALSPEED
if USB_GADGET_DOWNLOAD
-config G_DNL_MANUFACTURER
- string "Vendor name of USB device"
-
-config G_DNL_VENDOR_NUM
- hex "Vendor ID of USB device"
+config USB_FUNCTION_MASS_STORAGE
+ bool "Enable USB mass storage gadget"
+ help
+ Enable mass storage protocol support in U-Boot. It allows exporting
+ the eMMC/SD card content to HOST PC so it can be mounted.
+
+config USB_FUNCTION_ROCKUSB
+ bool "Enable USB rockusb gadget"
+ help
+ Rockusb protocol is widely used by Rockchip SoC based devices. It can
+ read/write info, image to/from devices. This enables the USB part of
+ the rockusb gadget.for more detail about Rockusb protocol, please see
+ doc/README.rockusb
+
+config USB_FUNCTION_SDP
+ bool "Enable USB SDP (Serial Download Protocol)"
+ help
+ Enable Serial Download Protocol (SDP) device support in U-Boot. This
+ allows to download images into memory and execute (jump to) them
+ using the same protocol as implemented by the i.MX family's boot ROM.
-config G_DNL_PRODUCT_NUM
- hex "Product ID of USB device"
+config USB_FUNCTION_THOR
+ bool "Enable USB THOR gadget"
+ help
+ Enable Tizen's THOR download protocol support in U-Boot. It
+ allows downloading images into memory and flash them to target device.
endif # USB_GADGET_DOWNLOAD
+config USB_ETHER
+ bool "USB Ethernet Gadget"
+ default y if ARCH_SUNXI && USB_MUSB_GADGET
+ help
+ Creates an Ethernet network device through a USB peripheral
+ controller. This will create a network interface on both the device
+ (U-Boot) and the host (remote device) that can be used just like any
+ other nework interface.
+ It will bind on the peripheral USB controller, ignoring the USB hosts
+ controllers in the system.
+
+if USB_ETHER
+
+choice
+ prompt "USB Ethernet Gadget Model"
+ default USB_ETH_RNDIS
+ help
+ There is several models (protocols) to implement Ethernet over USB
+ devices. The main ones are Microsoft's RNDIS and USB's CDC-Ethernet
+ (also called CDC-ECM). RNDIS is obviously compatible with Windows,
+ while CDC-ECM is not. Most other operating systems support both, so
+ if inter-operability is a concern, RNDIS is to be preferred.
+
+config USB_ETH_CDC
+ bool "CDC-ECM Protocol"
+ help
+ CDC (Communications Device Class) is the standard for Ethernet over
+ USB devices. While there's several alternatives, the most widely used
+ protocol is ECM (Ethernet Control Model). However, compatibility with
+ Windows is not that great.
+
+config USB_ETH_RNDIS
+ bool "RNDIS Protocol"
+ help
+ The RNDIS (Remote Network Driver Interface Specification) is a
+ Microsoft proprietary protocol to create an Ethernet device over USB.
+ Windows obviously supports it, as well as all the major operating
+ systems, so it's the best option for compatibility.
+
+endchoice
+
+config USBNET_DEVADDR
+ string "USB Gadget Ethernet device mac address"
+ default "de:ad:be:ef:00:01"
+ help
+ Ethernet MAC address of the device-side (ie. local board's) MAC
+ address of the usb_ether interface
+
+config USBNET_HOST_ADDR
+ string "USB Gadget Ethernet host mac address"
+ default "de:ad:be:ef:00:00"
+ help
+ Ethernet MAC address of the host-side (ie. remote device's) MAC
+ address of the usb_ether interface
+
+endif # USB_ETHER
+
endif # USB_GADGET
projects / people / ms / u-boot.git / blobdiff