usb: host: Move CONFIG_XHCI_FSL to Kconfig

[people/ms/u-boot.git] / drivers / usb / host / Kconfig

diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index 9a67e43c2d947501dcb5fb3d8ae3c0e46c4381e0..5264475fa521bf91c075d866b28ed7b88236663e 100644 (file)
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -31,13 +31,31 @@ config USB_XHCI_MVEBU
          SoCs, which includes Armada8K, Armada3700 and other Armada
          family SoCs.
 
+config USB_XHCI_PCI
+       bool "Support for PCI-based xHCI USB controller"
+       depends on DM_USB
+       default y if X86
+       help
+         Enables support for the PCI-based xHCI controller.
+
 config USB_XHCI_ROCKCHIP
        bool "Support for Rockchip on-chip xHCI USB controller"
        depends on ARCH_ROCKCHIP
+       depends on DM_REGULATOR
+       depends on DM_USB
        default y
        help
          Enables support for the on-chip xHCI controller on Rockchip SoCs.
 
+config USB_XHCI_STI
+       bool "Support for STMicroelectronics STiH407 family on-chip xHCI USB controller"
+       depends on ARCH_STI
+       default y
+       help
+         Enables support for the on-chip xHCI controller on STMicroelectronics
+         STiH407 family SoCs. This is a driver for the dwc3 to provide the glue logic
+         to configure the controller.
+
 config USB_XHCI_ZYNQMP
        bool "Support for Xilinx ZynqMP on-chip xHCI USB controller"
        depends on ARCH_ZYNQMP
@@ -53,6 +71,12 @@ config USB_XHCI_DRA7XX_INDEX
          Select the DRA7XX xHCI USB index.
          Current supported values: 0, 1.
 
+config USB_XHCI_FSL
+       bool "Support for NXP Layerscape on-chip xHCI USB controller"
+       default y if ARCH_LS1021A || FSL_LSCH3 || FSL_LSCH2
+       depends on !SPL_NO_USB
+       help
+         Enables support for the on-chip xHCI controller on NXP Layerscape SoCs.
 endif # USB_XHCI_HCD
 
 config USB_EHCI_HCD
@@ -133,6 +157,12 @@ config USB_EHCI_MSM
          This driver supports combination of Chipidea USB controller
          and Synapsys USB PHY in host mode only.
 
+config USB_EHCI_PCI
+       bool "Support for PCI-based EHCI USB controller"
+       default y if X86
+       help
+         Enables support for the PCI-based EHCI controller.
+
 config USB_EHCI_ZYNQ
        bool "Support for Xilinx Zynq on-chip EHCI USB controller"
        depends on ARCH_ZYNQ
@@ -191,3 +221,13 @@ config USB_UHCI_HCD
 if USB_UHCI_HCD
 
 endif # USB_UHCI_HCD
+
+config USB_DWC2
+       bool "DesignWare USB2 Core support"
+       select USB_HOST
+       ---help---
+         The DesignWare USB 2.0 controller is compliant with the
+         USB-Implementers Forum (USB-IF) USB 2.0 specifications.
+         Hi-Speed (480 Mbps), Full-Speed (12 Mbps), and Low-Speed (1.5 Mbps)
+         operation is compliant to the controller Supplement. If you want to
+         enable this controller in host mode, say Y.