#define PORT_SCR_ERR 0x30 /* SATA phy register: SError */
#define PORT_SCR_ACT 0x34 /* SATA phy register: SActive */
+#ifdef CONFIG_SUNXI_AHCI
+#define PORT_P0DMACR 0x70 /* SUNXI specific "DMA register" */
+#endif
+
/* PORT_IRQ_{STAT,MASK} bits */
#define PORT_IRQ_COLD_PRES (1 << 31) /* cold presence detect */
#define PORT_IRQ_TF_ERR (1 << 30) /* task file error */
| PORT_IRQ_DMAS_FIS | PORT_IRQ_PIOS_FIS \
| PORT_IRQ_D2H_REG_FIS
+/* PORT_SCR_STAT bits */
+#define PORT_SCR_STAT_DET_MASK 0x3
+#define PORT_SCR_STAT_DET_COMINIT 0x1
+#define PORT_SCR_STAT_DET_PHYRDY 0x3
+
/* PORT_CMD bits */
#define PORT_CMD_ATAPI (1 << 24) /* Device is ATAPI */
#define PORT_CMD_LIST_ON (1 << 15) /* cmd list DMA engine running */
#define AHCI_MAX_PORTS 32
-/* SETFEATURES stuff */
-#define SETFEATURES_XFER 0x03
-#define XFER_UDMA_7 0x47
-#define XFER_UDMA_6 0x46
-#define XFER_UDMA_5 0x45
-#define XFER_UDMA_4 0x44
-#define XFER_UDMA_3 0x43
-#define XFER_UDMA_2 0x42
-#define XFER_UDMA_1 0x41
-#define XFER_UDMA_0 0x40
-#define XFER_MW_DMA_2 0x22
-#define XFER_MW_DMA_1 0x21
-#define XFER_MW_DMA_0 0x20
-#define XFER_SW_DMA_2 0x12
-#define XFER_SW_DMA_1 0x11
-#define XFER_SW_DMA_0 0x10
-#define XFER_PIO_4 0x0C
-#define XFER_PIO_3 0x0B
-#define XFER_PIO_2 0x0A
-#define XFER_PIO_1 0x09
-#define XFER_PIO_0 0x08
-#define XFER_PIO_SLOW 0x00
-
#define ATA_FLAG_SATA (1 << 3)
#define ATA_FLAG_NO_LEGACY (1 << 4) /* no legacy mode check */
#define ATA_FLAG_MMIO (1 << 6) /* use MMIO, not PIO */
};
struct ahci_ioports {
- u32 cmd_addr;
- u32 scr_addr;
- u32 port_mmio;
+ void __iomem *cmd_addr;
+ void __iomem *scr_addr;
+ void __iomem *port_mmio;
struct ahci_cmd_hdr *cmd_slot;
struct ahci_sg *cmd_tbl_sg;
- u32 cmd_tbl;
+ ulong cmd_tbl;
u32 rx_fis;
};
-struct ahci_probe_ent {
+/**
+ * struct ahci_uc_priv - information about an AHCI controller
+ *
+ * When driver model is used, this is accessible using dev_get_uclass_priv(dev)
+ * where dev is the controller (although at present it sometimes stands alone).
+ */
+struct ahci_uc_priv {
+#if defined(CONFIG_DM_PCI) || defined(CONFIG_DM_SCSI)
+ /*
+ * TODO(sjg@chromium.org): Drop this once this structure is only used
+ * in a driver-model context (i.e. attached to a device with
+ * dev_get_uclass_priv()
+ */
+ struct udevice *dev;
+#else
pci_dev_t dev;
+#endif
struct ahci_ioports port[AHCI_MAX_PORTS];
+ u16 *ataid[AHCI_MAX_PORTS];
u32 n_ports;
u32 hard_port_no;
u32 host_flags;
u32 host_set_flags;
- u32 mmio_base;
+ void __iomem *mmio_base;
u32 pio_mask;
u32 udma_mask;
u32 flags;
u32 link_port_map; /*linkup port map*/
};
-int ahci_init(u32 base);
+struct ahci_ops {
+ /**
+ * reset() - reset the controller
+ *
+ * @dev: Controller to reset
+ * @return 0 if OK, -ve on error
+ */
+ int (*reset)(struct udevice *dev);
+
+ /**
+ * port_status() - get the status of a SATA port
+ *
+ * @dev: Controller to reset
+ * @port: Port number to check (0 for first)
+ * @return 0 if detected, -ENXIO if nothing on port, other -ve on error
+ */
+ int (*port_status)(struct udevice *dev, int port);
+
+ /**
+ * scan() - scan SATA ports
+ *
+ * @dev: Controller to scan
+ * @return 0 if OK, -ve on error
+ */
+ int (*scan)(struct udevice *dev);
+};
+
+#define ahci_get_ops(dev) ((struct ahci_ops *)(dev)->driver->ops)
+
+/**
+ * sata_reset() - reset the controller
+ *
+ * @dev: Controller to reset
+ * @return 0 if OK, -ve on error
+ */
+int sata_reset(struct udevice *dev);
+
+/**
+ * sata_port_status() - get the status of a SATA port
+ *
+ * @dev: Controller to reset
+ * @port: Port number to check (0 for first)
+ * @return 0 if detected, -ENXIO if nothin on port, other -ve on error
+ */
+int sata_dm_port_status(struct udevice *dev, int port);
+
+/**
+ * sata_scan() - scan SATA ports
+ *
+ * @dev: Controller to scan
+ * @return 0 if OK, -ve on error
+ */
+int sata_scan(struct udevice *dev);
+
+int ahci_init(void __iomem *base);
+int ahci_reset(void __iomem *base);
+
+/**
+ * ahci_init_one_dm() - set up a single AHCI port
+ *
+ * @dev: Controller to init
+ */
+int ahci_init_one_dm(struct udevice *dev);
+
+/**
+ * ahci_start_ports_dm() - start all AHCI ports for a controller
+ *
+ * @dev: Controller containing ports to start
+ */
+int ahci_start_ports_dm(struct udevice *dev);
+
+/**
+ * ahci_init_dm() - init AHCI for a controller, finding all ports
+ *
+ * @dev: Device to init
+ */
+int ahci_init_dm(struct udevice *dev, void __iomem *base);
+
+/**
+ * ahci_bind_scsi() - bind a new SCSI bus as a child
+ *
+ * Note that the SCSI bus device will itself bind block devices
+ *
+ * @ahci_dev: AHCI parent device
+ * @devp: Returns new SCSI bus device
+ * @return 0 if OK, -ve on error
+ */
+int ahci_bind_scsi(struct udevice *ahci_dev, struct udevice **devp);
+
+/**
+ * ahci_probe_scsi() - probe and scan the attached SCSI bus
+ *
+ * Note that the SCSI device will itself bind block devices for any storage
+ * devices it finds.
+ *
+ * @ahci_dev: AHCI parent device
+ * @base: Base address of AHCI port
+ * @return 0 if OK, -ve on error
+ */
+int ahci_probe_scsi(struct udevice *ahci_dev, ulong base);
+
+/**
+ * ahci_probe_scsi_pci() - probe and scan the attached SCSI bus on PCI
+ *
+ * Note that the SCSI device will itself bind block devices for any storage
+ * devices it finds.
+ *
+ * @ahci_dev: AHCI parent device
+ * @return 0 if OK, -ve on error
+ */
+int ahci_probe_scsi_pci(struct udevice *ahci_dev);
#endif
projects / people / ms / u-boot.git / blobdiff