*
* This file contains structures and information for the communication
* processor channels. Some CPM control and status is available
- * throught the MPC8xx internal memory map. See immap.h for details.
+ * through the MPC8xx internal memory map. See immap.h for details.
* This file only contains what I need for the moment, not the total
* CPM capabilities. I (or someone else) will add definitions as they
* are needed. -- Dan
/*
* DPRAM defines and allocation functions
*/
-
-/* The dual ported RAM is multi-functional. Some areas can be (and are
- * being) used for microcode. There is an area that can only be used
- * as data ram for buffer descriptors, which is all we use right now.
- * Currently the first 512 and last 256 bytes are used for microcode.
- */
-#ifdef CONFIG_SYS_ALLOC_DPRAM
-
-#define CPM_DATAONLY_BASE ((uint)0x0800)
-#define CPM_DATAONLY_SIZE ((uint)0x0700)
-#define CPM_DP_NOSPACE ((uint)0x7fffffff)
-
-#else
-
#define CPM_SERIAL_BASE 0x0800
#define CPM_I2C_BASE 0x0820
#define CPM_SPI_BASE 0x0840
#define CPM_POST_BASE 0x0980
#define CPM_WLKBD_BASE 0x0a00
-#endif
-
-#ifndef CONFIG_SYS_CPM_POST_WORD_ADDR
-#define CPM_POST_WORD_ADDR 0x07FC
-#else
-#define CPM_POST_WORD_ADDR CONFIG_SYS_CPM_POST_WORD_ADDR
-#endif
-
-#ifndef CONFIG_SYS_CPM_BOOTCOUNT_ADDR
-#define CPM_BOOTCOUNT_ADDR (CPM_POST_WORD_ADDR - 2*sizeof(ulong))
-#else
-#define CPM_BOOTCOUNT_ADDR CONFIG_SYS_CPM_BOOTCOUNT_ADDR
-#endif
-
#define BD_IIC_START ((uint) 0x0400) /* <- please use CPM_I2C_BASE !! */
/* Export the base address of the communication processor registers
#define BD_SC_INTRPT ((ushort)0x1000) /* Interrupt on change */
#define BD_SC_LAST ((ushort)0x0800) /* Last buffer in frame */
#define BD_SC_TC ((ushort)0x0400) /* Transmit CRC */
-#define BD_SC_CM ((ushort)0x0200) /* Continous mode */
+#define BD_SC_CM ((ushort)0x0200) /* Continuous mode */
#define BD_SC_ID ((ushort)0x0100) /* Rec'd too many idles */
#define BD_SC_P ((ushort)0x0100) /* xmt preamble */
#define BD_SC_BR ((ushort)0x0020) /* Break received */
ushort sen_taddrl; /* temp address (LSB) */
} scc_enet_t;
-/**********************************************************************
- *
- * Board specific configuration settings.
- *
- * Please note that we use the presence of a #define SCC_ENET and/or
- * #define FEC_ENET to enable the SCC resp. FEC ethernet drivers.
- **********************************************************************/
-
-/*** BSEIP **********************************************************/
-
-#ifdef CONFIG_BSEIP
-/* This ENET stuff is for the MPC823 with ethernet on SCC2.
- * This is unique to the BSE ip-Engine board.
- */
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define PA_ENET_RXD ((ushort)0x0004)
-#define PA_ENET_TXD ((ushort)0x0008)
-#define PA_ENET_TCLK ((ushort)0x0100)
-#define PA_ENET_RCLK ((ushort)0x0200)
-#define PB_ENET_TENA ((uint)0x00002000)
-#define PC_ENET_CLSN ((ushort)0x0040)
-#define PC_ENET_RENA ((ushort)0x0080)
-
-/* BSE uses port B and C bits for PHY control also.
-*/
-#define PB_BSE_POWERUP ((uint)0x00000004)
-#define PB_BSE_FDXDIS ((uint)0x00008000)
-#define PC_BSE_LOOPBACK ((ushort)0x0800)
-
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00002c00)
-#endif /* CONFIG_BSEIP */
-
-/*** BSEIP **********************************************************/
-
-#ifdef CONFIG_FLAGADM
-/* Enet configuration for the FLAGADM */
-/* Enet on SCC2 */
-
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define PA_ENET_RXD ((ushort)0x0004)
-#define PA_ENET_TXD ((ushort)0x0008)
-#define PA_ENET_TCLK ((ushort)0x0100)
-#define PA_ENET_RCLK ((ushort)0x0400)
-#define PB_ENET_TENA ((uint)0x00002000)
-#define PC_ENET_CLSN ((ushort)0x0040)
-#define PC_ENET_RENA ((ushort)0x0080)
-
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00003400)
-#endif /* CONFIG_FLAGADM */
-
-/*** ELPT860 *********************************************************/
-
-#ifdef CONFIG_ELPT860
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use.
- */
-# define PROFF_ENET PROFF_SCC1
-# define CPM_CR_ENET CPM_CR_CH_SCC1
-# define SCC_ENET 0
-
-# define PA_ENET_RXD ((ushort)0x0001) /* PA 15 */
-# define PA_ENET_TXD ((ushort)0x0002) /* PA 14 */
-# define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
-# define PA_ENET_TCLK ((ushort)0x0200) /* PA 6 */
-
-# define PC_ENET_TENA ((ushort)0x0001) /* PC 15 */
-# define PC_ENET_CLSN ((ushort)0x0010) /* PC 11 */
-# define PC_ENET_RENA ((ushort)0x0020) /* PC 10 */
-
-/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK1) to
- * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
- */
-# define SICR_ENET_MASK ((uint)0x000000FF)
-# define SICR_ENET_CLKRT ((uint)0x00000025)
-#endif /* CONFIG_ELPT860 */
-
-/*** ESTEEM 192E **************************************************/
-#ifdef CONFIG_ESTEEM192E
-/* ESTEEM192E
- * This ENET stuff is for the MPC850 with ethernet on SCC2. This
- * is very similar to the RPX-Lite configuration.
- * Note TENA , LOOPBACK , FDPLEX_DIS on Port B.
- */
-
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-
-#define PA_ENET_RXD ((ushort)0x0004)
-#define PA_ENET_TXD ((ushort)0x0008)
-#define PA_ENET_TCLK ((ushort)0x0200)
-#define PA_ENET_RCLK ((ushort)0x0800)
-#define PB_ENET_TENA ((uint)0x00002000)
-#define PC_ENET_CLSN ((ushort)0x0040)
-#define PC_ENET_RENA ((ushort)0x0080)
-
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00003d00)
-
-#define PB_ENET_LOOPBACK ((uint)0x00004000)
-#define PB_ENET_FDPLEX_DIS ((uint)0x00008000)
-
-#endif
-
-/*** FPS850L, FPS860L ************************************************/
-
-#if defined(CONFIG_FPS850L) || defined(CONFIG_FPS860L)
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC2 use.
- */
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
-
-#define PC_ENET_TENA ((ushort)0x0002) /* PC 14 */
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-
-/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
- * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00002600)
-#endif /* CONFIG_FPS850L, CONFIG_FPS860L */
-
-/*** GEN860T **********************************************************/
-#if defined(CONFIG_GEN860T)
-#undef SCC_ENET
-#define FEC_ENET
-
-#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
-#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
-#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
-#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
-#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
-#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
-#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
-#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
-#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
-#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
-#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
-#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
-#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
-#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3-15 */
-#endif /* CONFIG_GEN860T */
-
-/*** HERMES-PRO ******************************************************/
-
-/* The HERMES-PRO uses the FEC on a MPC860T for Ethernet */
-
-#ifdef CONFIG_HERMES
-
-#define FEC_ENET /* use FEC for EThernet */
-#undef SCC_ENET
-
-
-#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
-#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
-#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
-#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
-#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
-#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
-#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
-#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
-#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
-#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
-#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
-#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
-#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
-
-#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
-
-#endif /* CONFIG_HERMES */
-
-/*** ICU862 **********************************************************/
-
-#if defined(CONFIG_ICU862)
-
-#ifdef CONFIG_FEC_ENET
-#define FEC_ENET /* use FEC for EThernet */
-#endif /* CONFIG_FEC_ETHERNET */
-
-#endif /* CONFIG_ICU862 */
-
-/*** IP860 **********************************************************/
-
-#if defined(CONFIG_IP860)
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use.
- */
-#define PROFF_ENET PROFF_SCC1
-#define CPM_CR_ENET CPM_CR_CH_SCC1
-#define SCC_ENET 0
-#define PA_ENET_RXD ((ushort)0x0001) /* PA 15 */
-#define PA_ENET_TXD ((ushort)0x0002) /* PA 14 */
-#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
-#define PA_ENET_TCLK ((ushort)0x0100) /* PA 7 */
-
-#define PC_ENET_TENA ((ushort)0x0001) /* PC 15 */
-#define PC_ENET_CLSN ((ushort)0x0010) /* PC 11 */
-#define PC_ENET_RENA ((ushort)0x0020) /* PC 10 */
-
-#define PB_ENET_RESET (uint)0x00000008 /* PB 28 */
-#define PB_ENET_JABD (uint)0x00000004 /* PB 29 */
-
-/* Control bits in the SICR to route TCLK (CLK1) and RCLK (CLK2) to
- * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x000000ff)
-#define SICR_ENET_CLKRT ((uint)0x0000002C)
-#endif /* CONFIG_IP860 */
-
-/*** IVMS8 **********************************************************/
-
-/* The IVMS8 uses the FEC on a MPC860T for Ethernet */
-
-#if defined(CONFIG_IVMS8) || defined(CONFIG_IVML24)
-
-#define FEC_ENET /* use FEC for EThernet */
-#undef SCC_ENET
-
-#define PB_ENET_POWER ((uint)0x00010000) /* PB 15 */
-
-#define PC_ENET_RESET ((ushort)0x0010) /* PC 11 */
-
-#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
-#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
-#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
-#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
-#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
-#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
-#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
-#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
-#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
-#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
-#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
-#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
-#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
-
-#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
-
-#endif /* CONFIG_IVMS8, CONFIG_IVML24 */
-
-/*** KUP4K, KUP4X ****************************************************/
-/* The KUP4 boards uses the FEC on a MPC8xx for Ethernet */
-
-#if defined(CONFIG_KUP4K) || defined(CONFIG_KUP4X)
-
-#define FEC_ENET /* use FEC for EThernet */
-#undef SCC_ENET
-
-#define PB_ENET_POWER ((uint)0x00010000) /* PB 15 */
-
-#define PC_ENET_RESET ((ushort)0x0010) /* PC 11 */
-
-#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
-#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
-#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
-#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
-#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
-#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
-#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
-#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
-#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
-#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
-#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
-#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
-#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
-
-#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
-
-#endif /* CONFIG_KUP4K */
-
-/*** LWMON **********************************************************/
-
-#if defined(CONFIG_LWMON)
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC2 use.
- */
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0800) /* PA 4 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
-
-#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
-
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK4) to
- * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00003E00)
-#endif /* CONFIG_LWMON */
-
-/*** KM8XX *********************************************************/
-
-/* The KM8XX Service Module uses SCC3 for Ethernet */
-
-#ifdef CONFIG_KM8XX
-#define PROFF_ENET PROFF_SCC3 /* Ethernet on SCC3 */
-#define CPM_CR_ENET CPM_CR_CH_SCC3
-#define SCC_ENET 2
-#define PA_ENET_RXD ((ushort)0x0010) /* PA 11 */
-#define PA_ENET_TXD ((ushort)0x0020) /* PA 10 */
-#define PA_ENET_RCLK ((ushort)0x1000) /* PA 3 CLK 5 */
-#define PA_ENET_TCLK ((ushort)0x2000) /* PA 2 CLK 6 */
-
-#define PC_ENET_TENA ((ushort)0x0004) /* PC 13 */
-
-#define PC_ENET_RENA ((ushort)0x0200) /* PC 6 */
-#define PC_ENET_CLSN ((ushort)0x0100) /* PC 7 */
-
-/* Control bits in the SICR to route TCLK (CLK6) and RCLK (CLK5) to
- * SCC3. Also, make sure GR3 (bit 8) and SC3 (bit 9) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x00FF0000)
-#define SICR_ENET_CLKRT ((uint)0x00250000)
-#endif /* CONFIG_KM8XX */
-
-
-/*** MHPC ********************************************************/
-
-#if defined(CONFIG_MHPC)
-/* This ENET stuff is for the MHPC with ethernet on SCC2.
- * Note TENA is on Port B.
- */
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
-#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00002e00) /* RCLK-CLK2, TCLK-CLK3 */
-#endif /* CONFIG_MHPC */
-
-/*** NETVIA *******************************************************/
-
-/* SinoVee Microsystems SC8xx series FEL8xx-AT,SC823,SC850,SC855T,SC860T */
-#if ( defined CONFIG_SVM_SC8xx )
-# ifndef CONFIG_FEC_ENET
-
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-
- /* Bits in parallel I/O port registers that have to be set/cleared
- * * * * to configure the pins for SCC2 use.
- * * * */
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0400) /* PA 5 */
-#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */
-
-#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
-
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
- * * * * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- * * * */
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00003700)
-
-# else /* Use FEC for Fast Ethernet */
-
-#undef SCC_ENET
-#define FEC_ENET
-
-#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
-#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
-#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
-#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
-#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
-#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
-#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
-#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
-#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
-#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
-#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
-#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
-#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
-
-#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
-
-# endif /* CONFIG_FEC_ENET */
-#endif /* CONFIG_SVM_SC8xx */
-
-
-#if defined(CONFIG_NETVIA)
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC2 use.
- */
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
-#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */
-
-#if !defined(CONFIG_NETVIA_VERSION) || CONFIG_NETVIA_VERSION == 1
-# define PB_ENET_PDN ((ushort)0x4000) /* PB 17 */
-#elif CONFIG_NETVIA_VERSION >= 2
-# define PC_ENET_PDN ((ushort)0x0008) /* PC 12 */
-#endif
-
-#define PB_ENET_TENA ((ushort)0x2000) /* PB 18 */
-
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
- * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00002f00)
-
-#endif /* CONFIG_NETVIA */
-
-/*** SM850 *********************************************************/
-
-/* The SM850 Service Module uses SCC2 for IrDA and SCC3 for Ethernet */
-
-#ifdef CONFIG_SM850
-#define PROFF_ENET PROFF_SCC3 /* Ethernet on SCC3 */
-#define CPM_CR_ENET CPM_CR_CH_SCC3
-#define SCC_ENET 2
-#define PB_ENET_RXD ((uint)0x00000004) /* PB 29 */
-#define PB_ENET_TXD ((uint)0x00000002) /* PB 30 */
-#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
-
-#define PC_ENET_LBK ((ushort)0x0008) /* PC 12 */
-#define PC_ENET_TENA ((ushort)0x0004) /* PC 13 */
-
-#define PC_ENET_RENA ((ushort)0x0800) /* PC 4 */
-#define PC_ENET_CLSN ((ushort)0x0400) /* PC 5 */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
- * SCC3. Also, make sure GR3 (bit 8) and SC3 (bit 9) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x00FF0000)
-#define SICR_ENET_CLKRT ((uint)0x00260000)
-#endif /* CONFIG_SM850 */
-
-/*** SPD823TS ******************************************************/
-
-#ifdef CONFIG_SPD823TS
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC2 use.
- */
-#define PROFF_ENET PROFF_SCC2 /* Ethernet on SCC2 */
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define PA_ENET_MDC ((ushort)0x0001) /* PA 15 !!! */
-#define PA_ENET_MDIO ((ushort)0x0002) /* PA 14 !!! */
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
-
-#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
-
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-#define PC_ENET_RESET ((ushort)0x0100) /* PC 7 !!! */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK2) to
- * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00002E00)
-#endif /* CONFIG_SPD823TS */
-
-/*** SXNI855T ******************************************************/
-
-#if defined(CONFIG_SXNI855T)
-
-#ifdef CONFIG_FEC_ENET
-#define FEC_ENET /* use FEC for Ethernet */
-#endif /* CONFIG_FEC_ETHERNET */
-
-#endif /* CONFIG_SXNI855T */
-
-/*** MVS1, TQM823L/M, TQM850L/M, TQM885D, R360MPI **********/
-
-#if (defined(CONFIG_MVS) && CONFIG_MVS < 2) || \
- defined(CONFIG_R360MPI) || \
- defined(CONFIG_RRVISION)|| defined(CONFIG_TQM823L) || \
- defined(CONFIG_TQM823M) || defined(CONFIG_TQM850L) || \
- defined(CONFIG_TQM850M) || defined(CONFIG_TQM885D) || \
- defined(CONFIG_RRVISION)|| defined(CONFIG_VIRTLAB2)
-
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC2 use.
- */
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#if (!defined(CONFIG_TK885D)) /* TK885D does not use SCC Ethernet */
-#define SCC_ENET 1
-#endif
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
-
-#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
-
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-#if defined(CONFIG_R360MPI)
-#define PC_ENET_LBK ((ushort)0x0008) /* PC 12 */
-#endif /* CONFIG_R360MPI */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
- * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00002600)
-
-# ifdef CONFIG_FEC_ENET /* Use FEC for Fast Ethernet */
-#define FEC_ENET
-# endif /* CONFIG_FEC_ENET */
-
-#endif /* CONFIG_MVS v1, CONFIG_TQM823L/M, CONFIG_TQM850L/M, etc. */
-
-/*** TQM855L/M, TQM860L/M, TQM862L/M, TQM866L/M *********************/
-
-#if defined(CONFIG_TQM855L) || defined(CONFIG_TQM855M) || \
- defined(CONFIG_TQM860L) || defined(CONFIG_TQM860M) || \
- defined(CONFIG_TQM862L) || defined(CONFIG_TQM862M) || \
- defined(CONFIG_TQM866L) || defined(CONFIG_TQM866M)
-
-# ifdef CONFIG_SCC1_ENET /* use SCC for 10Mbps Ethernet */
-
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use.
- */
-#define PROFF_ENET PROFF_SCC1
-#define CPM_CR_ENET CPM_CR_CH_SCC1
-#define SCC_ENET 0
-#define PA_ENET_RXD ((ushort)0x0001) /* PA 15 */
-#define PA_ENET_TXD ((ushort)0x0002) /* PA 14 */
-#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
-
-#define PC_ENET_TENA ((ushort)0x0001) /* PC 15 */
-#define PC_ENET_CLSN ((ushort)0x0010) /* PC 11 */
-#define PC_ENET_RENA ((ushort)0x0020) /* PC 10 */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
- * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x000000ff)
-#define SICR_ENET_CLKRT ((uint)0x00000026)
-
-# endif /* CONFIG_SCC1_ENET */
-
-# ifdef CONFIG_FEC_ENET /* Use FEC for Fast Ethernet */
-
-#define FEC_ENET
-
-#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
-#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
-#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
-#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
-#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
-#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
-#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
-#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
-#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
-#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
-#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
-#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
-#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
-
-#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
-
-# endif /* CONFIG_FEC_ENET */
-#endif /* CONFIG_TQM855L/M, TQM860L/M, TQM862L/M */
-
/*********************************************************************/
/* SCC Event register as used by Ethernet.
#define SPMODE_LENMSK ((ushort)0x00f0) /* character length */
#define SPMODE_PMMSK ((ushort)0x000f) /* prescale modulus */
-#define SPMODE_LEN(x) ((((x)-1)&0xF)<<4)
-#define SPMODE_PM(x) ((x) &0xF)
+#define SPMODE_LEN(x) ((((x) - 1) & 0xF) << 4)
+#define SPMODE_PM(x) ((x) & 0xF)
/* HDLC parameter RAM.
*/
#define CPMVEC_PIO_PC4 ((ushort)0x01 | CPMVEC_OFFSET)
#define CPMVEC_ERROR ((ushort)0x00 | CPMVEC_OFFSET)
-extern void irq_install_handler(int vec, void (*handler)(void *), void *dev_id);
+void irq_install_handler(int vec, void (*handler)(void *), void *dev_id);
/* CPM interrupt configuration vector.
*/
#define CICR_SCC_SCC3 ((uint)0x00200000) /* SCC3 @ SCCc */
#define CICR_SCB_SCC2 ((uint)0x00040000) /* SCC2 @ SCCb */
#define CICR_SCA_SCC1 ((uint)0x00000000) /* SCC1 @ SCCa */
-#define CICR_IRL_MASK ((uint)0x0000e000) /* Core interrrupt */
+#define CICR_IRL_MASK ((uint)0x0000e000) /* Core interrupt */
#define CICR_HP_MASK ((uint)0x00001f00) /* Hi-pri int. */
#define CICR_IEN ((uint)0x00000080) /* Int. enable */
#define CICR_SPS ((uint)0x00000001) /* SCC Spread */
projects / people / ms / u-boot.git / blobdiff