configs: Re-sync with cmd/Kconfig

[people/ms/u-boot.git] / include / configs / B4860QDS.h

diff --git a/include/configs/B4860QDS.h b/include/configs/B4860QDS.h
index ad3f52ac929d224a47696e3afbaff582a92f8c8d..94c8253e60d68dfec164f03899815090e02b35bb 100644 (file)
--- a/include/configs/B4860QDS.h
+++ b/include/configs/B4860QDS.h
@@ -7,7 +7,6 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-#define CONFIG_SYS_GENERIC_BOARD
 #define CONFIG_DISPLAY_BOARDINFO
 
 /*
@@ -460,13 +459,13 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_INIT_RAM_ADDR       0xfdd00000      /* Initial L1 address */
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH     0xf
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW      0xfe0ec000
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW      0xfe03c000
 /* The assembler doesn't like typecast */
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
        ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
          CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 #else
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS  0xfe0ec000 /* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS  0xfe03c000 /* Initial L1 address */
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
 #endif
@@ -484,7 +483,6 @@ unsigned long get_board_ddr_clk(void);
  * shorted - index 1
  */
 #define CONFIG_CONS_INDEX      1
-#define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
 #define CONFIG_SYS_NS16550_CLK         (get_bus_freq(0)/2)
@@ -500,20 +498,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_CONSOLE_IS_IN_ENV   /* determine from environment */
 #endif
 
-
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_OF_STDOUT_VIA_ALIAS
-
-/* new uImage format support */
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE     /* enable fit_format_{error,warning}() */
-
 /* I2C */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_FSL             /* Use FSL common I2C driver */
@@ -588,9 +572,6 @@ unsigned long get_board_ddr_clk(void);
 /*
  * eSPI - Enhanced SPI
  */
-#define CONFIG_FSL_ESPI
-#define CONFIG_SPI_FLASH_SST
-#define CONFIG_CMD_SF
 #define CONFIG_SF_DEFAULT_SPEED         10000000
 #define CONFIG_SF_DEFAULT_MODE          0
 
@@ -731,7 +712,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_FM1_10GEC1_PHY_ADDR 0x7      /*SLOT 1*/
 #define CONFIG_SYS_FM1_10GEC2_PHY_ADDR 0x6      /*SLOT 2*/
 
-
 #define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR    0x1c
 #define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR    0x1d
 #define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR    0x1e
@@ -754,15 +734,9 @@ unsigned long get_board_ddr_clk(void);
  * Command line configuration.
  */
 #define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
 #define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
 #define CONFIG_CMD_ERRATA
-#define CONFIG_CMD_GREPENV
 #define CONFIG_CMD_IRQ
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
 #define CONFIG_CMD_REGINFO
 
 #ifdef CONFIG_PCI
@@ -784,11 +758,9 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_USB_EHCI
 
 #ifdef CONFIG_USB_EHCI
-#define CONFIG_CMD_USB
 #define CONFIG_USB_STORAGE
 #define CONFIG_USB_EHCI_FSL
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_CMD_EXT2
 #endif
 #endif
 
@@ -929,8 +901,4 @@ unsigned long get_board_ddr_clk(void);
 
 #include <asm/fsl_secure_boot.h>
 
-#ifdef CONFIG_SECURE_BOOT
-#define CONFIG_CMD_BLOB
-#endif
-
 #endif /* __CONFIG_H */