configs: Re-sync with cmd/Kconfig

[people/ms/u-boot.git] / include / configs / BSC9132QDS.h

diff --git a/include/configs/BSC9132QDS.h b/include/configs/BSC9132QDS.h
index 54dcf3b9548de2086ef5aa597218ce313b0e587c..3a733795ae2066d5c24d31fc468486b4dd5779d1 100644 (file)
--- a/include/configs/BSC9132QDS.h
+++ b/include/configs/BSC9132QDS.h
@@ -93,7 +93,6 @@
 
 #define CONFIG_CMD_PCI
 
-
 /*
  * PCI Windows
  * Memory space is mapped 1-1, but I/O space must start from 0.
@@ -223,7 +222,6 @@ combinations. this should be removed later
 #define CONFIG_SYS_DDR_TIMING_5        CONFIG_SYS_DDR_TIMING_5_800
 #endif
 
-
 /* relocated CCSRBAR */
 #define CONFIG_SYS_CCSRBAR     CONFIG_SYS_CCSRBAR_DEFAULT
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW    CONFIG_SYS_CCSRBAR_DEFAULT
@@ -396,9 +394,9 @@ combinations. this should be removed later
 
 #define CONFIG_SYS_INIT_RAM_LOCK
 #define CONFIG_SYS_INIT_RAM_ADDR       0xffd00000      /* stack in RAM */
-#define CONFIG_SYS_INIT_RAM_END                0x00004000 /* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_SIZE       0x00004000 /* End of used area in RAM */
 
-#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_END \
+#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_SIZE \
                                                - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
 
@@ -408,7 +406,6 @@ combinations. this should be removed later
 /* Serial Port */
 #define CONFIG_CONS_INDEX      1
 #undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
 #define CONFIG_SYS_NS16550_CLK         get_bus_freq(0)
@@ -426,23 +423,6 @@ combinations. this should be removed later
 #define CONFIG_SYS_NS16550_COM3        (CONFIG_SYS_CCSRBAR + 0x4700)
 #define CONFIG_SYS_NS16550_COM4        (CONFIG_SYS_CCSRBAR + 0x4800)
 
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER    /* hush parser */
-#ifdef CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#endif
-
-/*
- * Pass open firmware flat tree
- */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_OF_STDOUT_VIA_ALIAS
-
-/* new uImage format support */
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE     /* enable fit_format_{error,warning}() */
-
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_FSL
 #define CONFIG_SYS_FSL_I2C_SPEED       400800 /* I2C speed and slave address*/
@@ -463,7 +443,6 @@ combinations. this should be removed later
 
 /* enable read and write access to EEPROM */
 #define CONFIG_CMD_EEPROM
-#define CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
@@ -480,10 +459,7 @@ combinations. this should be removed later
  * used for SLIC
  */
 /* eSPI - Enhanced SPI */
-#define CONFIG_FSL_ESPI  /* SPI */
 #ifdef CONFIG_FSL_ESPI
-#define CONFIG_SPI_FLASH_SPANSION
-#define CONFIG_CMD_SF
 #define CONFIG_SF_DEFAULT_SPEED                10000000
 #define CONFIG_SF_DEFAULT_MODE         SPI_MODE_0
 #endif
@@ -522,7 +498,6 @@ combinations. this should be removed later
 
 #define CONFIG_MMC
 #ifdef CONFIG_MMC
-#define CONFIG_CMD_MMC
 #define CONFIG_DOS_PARTITION
 #define CONFIG_FSL_ESDHC
 #define CONFIG_GENERIC_MMC
@@ -531,7 +506,6 @@ combinations. this should be removed later
 
 #define CONFIG_USB_EHCI  /* USB */
 #ifdef CONFIG_USB_EHCI
-#define CONFIG_CMD_USB
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_USB_EHCI_FSL
 #define CONFIG_USB_STORAGE
@@ -578,17 +552,11 @@ combinations. this should be removed later
  * Command line configuration.
  */
 #define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
 #define CONFIG_CMD_ERRATA
-#define CONFIG_CMD_I2C
 #define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
 #define CONFIG_CMD_REGINFO
 
 #if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI)
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
 #define CONFIG_DOS_PARTITION
 #endif
 
@@ -616,7 +584,6 @@ combinations. this should be removed later
 #define CONFIG_SYS_MAXARGS     16              /* max number of command args */
 #define CONFIG_SYS_BARGSIZE    CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
 
-
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 64 MB of memory, since this is
@@ -726,8 +693,4 @@ combinations. this should be removed later
 
 #include <asm/fsl_secure_boot.h>
 
-#ifdef CONFIG_SECURE_BOOT
-#define CONFIG_CMD_BLOB
-#endif
-
 #endif /* __CONFIG_H */