drivers/pci/Kconfig: Add PCI

[people/ms/u-boot.git] / include / configs / BSC9132QDS.h

diff --git a/include/configs/BSC9132QDS.h b/include/configs/BSC9132QDS.h
index e5cd26797cccd3a9cc43c0406836fc2683a7b7f4..430ba3a533e4d5cc61935933f754cbd4b5b55283 100644 (file)
--- a/include/configs/BSC9132QDS.h
+++ b/include/configs/BSC9132QDS.h
@@ -11,9 +11,6 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-#define CONFIG_SYS_GENERIC_BOARD
-#define CONFIG_DISPLAY_BOARDINFO
-
 #ifdef CONFIG_BSC9132QDS
 #define CONFIG_BSC9132
 #endif
@@ -45,8 +42,6 @@
 
 #ifdef CONFIG_NAND
 #define CONFIG_SPL_INIT_MINIMAL
-#define CONFIG_SPL_SERIAL_SUPPORT
-#define CONFIG_SPL_NAND_SUPPORT
 #define CONFIG_SPL_NAND_BOOT
 #define CONFIG_SPL_FLUSH_IMAGE
 #define CONFIG_SPL_TARGET              "u-boot-with-spl.bin"
@@ -84,9 +79,8 @@
 #define CONFIG_FSL_CAAM                        /* Enable SEC/CAAM */
 #define CONFIG_SYS_HAS_SERDES          /* common SERDES init code */
 
-#define CONFIG_PCI                     /* Enable PCI/PCIE */
 #if defined(CONFIG_PCI)
-#define CONFIG_PCIE1                   /* PCIE controler 1 (slot 1) */
+#define CONFIG_PCIE1                   /* PCIE controller 1 (slot 1) */
 #define CONFIG_FSL_PCI_INIT            /* Use common FSL init code */
 #define CONFIG_PCI_INDIRECT_BRIDGE     /* indirect PCI bridge support */
 #define CONFIG_FSL_PCIE_RESET          /* need PCIe reset errata */
@@ -94,8 +88,6 @@
 
 #define CONFIG_CMD_PCI
 
-#define CONFIG_E1000                   /*  E1000 pci Ethernet card*/
-
 /*
  * PCI Windows
  * Memory space is mapped 1-1, but I/O space must start from 0.
@@ -225,7 +217,6 @@ combinations. this should be removed later
 #define CONFIG_SYS_DDR_TIMING_5        CONFIG_SYS_DDR_TIMING_5_800
 #endif
 
-
 /* relocated CCSRBAR */
 #define CONFIG_SYS_CCSRBAR     CONFIG_SYS_CCSRBAR_DEFAULT
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW    CONFIG_SYS_CCSRBAR_DEFAULT
@@ -398,9 +389,9 @@ combinations. this should be removed later
 
 #define CONFIG_SYS_INIT_RAM_LOCK
 #define CONFIG_SYS_INIT_RAM_ADDR       0xffd00000      /* stack in RAM */
-#define CONFIG_SYS_INIT_RAM_END                0x00004000 /* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_SIZE       0x00004000 /* End of used area in RAM */
 
-#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_END \
+#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_SIZE \
                                                - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
 
@@ -410,7 +401,6 @@ combinations. this should be removed later
 /* Serial Port */
 #define CONFIG_CONS_INDEX      1
 #undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
 #define CONFIG_SYS_NS16550_CLK         get_bus_freq(0)
@@ -418,9 +408,6 @@ combinations. this should be removed later
 #define CONFIG_NS16550_MIN_FUNCTIONS
 #endif
 
-#define CONFIG_SERIAL_MULTI    1 /* Enable both serial ports */
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV   /* determine from environment */
-
 #define CONFIG_SYS_BAUDRATE_TABLE      \
        {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 
@@ -429,23 +416,6 @@ combinations. this should be removed later
 #define CONFIG_SYS_NS16550_COM3        (CONFIG_SYS_CCSRBAR + 0x4700)
 #define CONFIG_SYS_NS16550_COM4        (CONFIG_SYS_CCSRBAR + 0x4800)
 
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER    /* hush parser */
-#ifdef CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#endif
-
-/*
- * Pass open firmware flat tree
- */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_OF_STDOUT_VIA_ALIAS
-
-/* new uImage format support */
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE     /* enable fit_format_{error,warning}() */
-
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_FSL
 #define CONFIG_SYS_FSL_I2C_SPEED       400800 /* I2C speed and slave address*/
@@ -466,7 +436,6 @@ combinations. this should be removed later
 
 /* enable read and write access to EEPROM */
 #define CONFIG_CMD_EEPROM
-#define CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
@@ -483,10 +452,7 @@ combinations. this should be removed later
  * used for SLIC
  */
 /* eSPI - Enhanced SPI */
-#define CONFIG_FSL_ESPI  /* SPI */
 #ifdef CONFIG_FSL_ESPI
-#define CONFIG_SPI_FLASH_SPANSION
-#define CONFIG_CMD_SF
 #define CONFIG_SF_DEFAULT_SPEED                10000000
 #define CONFIG_SF_DEFAULT_MODE         SPI_MODE_0
 #endif
@@ -525,7 +491,6 @@ combinations. this should be removed later
 
 #define CONFIG_MMC
 #ifdef CONFIG_MMC
-#define CONFIG_CMD_MMC
 #define CONFIG_DOS_PARTITION
 #define CONFIG_FSL_ESDHC
 #define CONFIG_GENERIC_MMC
@@ -534,10 +499,8 @@ combinations. this should be removed later
 
 #define CONFIG_USB_EHCI  /* USB */
 #ifdef CONFIG_USB_EHCI
-#define CONFIG_CMD_USB
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_USB_EHCI_FSL
-#define CONFIG_USB_STORAGE
 #define CONFIG_HAS_FSL_DR_USB
 #endif
 
@@ -581,18 +544,11 @@ combinations. this should be removed later
  * Command line configuration.
  */
 #define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
 #define CONFIG_CMD_ERRATA
-#define CONFIG_CMD_I2C
 #define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
 #define CONFIG_CMD_REGINFO
 
 #if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI)
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
 #define CONFIG_DOS_PARTITION
 #endif
 
@@ -620,7 +576,6 @@ combinations. this should be removed later
 #define CONFIG_SYS_MAXARGS     16              /* max number of command args */
 #define CONFIG_SYS_BARGSIZE    CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
 
-
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 64 MB of memory, since this is
@@ -646,14 +601,6 @@ combinations. this should be removed later
                        "55m(fs),1m(uboot);ff800000.flash:1m(uboot)," \
                        "8m(kernel),512k(dtb),-(fs)"
 #endif
-/*
- * Override partitions in device tree using info
- * in "mtdparts" environment variable
- */
-#ifdef CONFIG_CMD_MTDPARTS
-#define CONFIG_FDT_FIXUP_PARTITIONS
-#endif
-
 /*
  * Environment Configuration
  */
@@ -669,7 +616,6 @@ combinations. this should be removed later
 #define CONFIG_UBOOTPATH       "u-boot.bin"
 
 #define CONFIG_BAUDRATE                115200
-#define CONFIG_BOOTDELAY       10 /* -1 disable auto-boot */
 
 #ifdef CONFIG_SDCARD
 #define CONFIG_DEF_HWCONFIG    "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0"
@@ -685,7 +631,7 @@ combinations. this should be removed later
        "consoledev=ttyS0\0"                            \
        "ramdiskaddr=2000000\0"                 \
        "ramdiskfile=rootfs.ext2.gz.uboot\0"            \
-       "fdtaddr=c00000\0"                              \
+       "fdtaddr=1e00000\0"                             \
        "fdtfile=bsc9132qds.dtb\0"              \
        "bdev=sda1\0"   \
        CONFIG_DEF_HWCONFIG\
@@ -730,8 +676,4 @@ combinations. this should be removed later
 
 #include <asm/fsl_secure_boot.h>
 
-#ifdef CONFIG_SECURE_BOOT
-#define CONFIG_CMD_BLOB
-#endif
-
 #endif /* __CONFIG_H */