#ifndef __CONFIG_H
#define __CONFIG_H
-#define CONFIG_DISPLAY_BOARDINFO
-
-#ifdef CONFIG_BSC9132QDS
-#define CONFIG_BSC9132
-#endif
-
#define CONFIG_MISC_INIT_R
#ifdef CONFIG_SDCARD
#define CONFIG_SYS_TEXT_BASE 0x11000000
#define CONFIG_RESET_VECTOR_ADDRESS 0x110bfffc
#endif
-#define CONFIG_SYS_FSL_ERRATUM_IFC_A002769 1
#ifdef CONFIG_SPIFLASH
#define CONFIG_RAMBOOT_SPIFLASH
#define CONFIG_SYS_RAMBOOT
#ifdef CONFIG_NAND
#define CONFIG_SPL_INIT_MINIMAL
-#define CONFIG_SPL_SERIAL_SUPPORT
-#define CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SPL_NAND_BOOT
#define CONFIG_SPL_FLUSH_IMAGE
#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
#endif
/* High Level Configuration Options */
-#define CONFIG_BOOKE /* BOOKE */
-#define CONFIG_E500 /* BOOKE e500 family */
-#define CONFIG_FSL_IFC /* Enable IFC Support */
#define CONFIG_FSL_CAAM /* Enable SEC/CAAM */
#define CONFIG_SYS_HAS_SERDES /* common SERDES init code */
-#define CONFIG_PCI /* Enable PCI/PCIE */
#if defined(CONFIG_PCI)
-#define CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */
+#define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */
#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */
#define CONFIG_CMD_PCI
-
/*
* PCI Windows
* Memory space is mapped 1-1, but I/O space must start from 0.
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
#define CONFIG_SYS_PCIE1_IO_PHYS 0xC0010000
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
-
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_DOS_PARTITION
#endif
-#define CONFIG_FSL_LAW /* Use common FSL init code */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_TSEC_ENET /* ethernet */
#define CONFIG_SYS_MEMTEST_END 0x01ffffff
/* DDR Setup */
-#define CONFIG_SYS_FSL_DDR3
#define CONFIG_SYS_SPD_BUS_NUM 0
#define SPD_EEPROM_ADDRESS1 0x54 /* I2C access */
#define SPD_EEPROM_ADDRESS2 0x56 /* I2C access */
#define CONFIG_SYS_DDR_TIMING_5 CONFIG_SYS_DDR_TIMING_5_800
#endif
-
/* relocated CCSRBAR */
#define CONFIG_SYS_CCSRBAR CONFIG_SYS_CCSRBAR_DEFAULT
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR_DEFAULT
*/
/* NOR Flash on IFC */
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SYS_NO_FLASH
-#endif
#define CONFIG_SYS_FLASH_BASE 0x88000000
#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* Max number of sector: 32M */
#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3
#endif
-#define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */
#define CONFIG_BOARD_EARLY_INIT_R
#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */
-#define CONFIG_SYS_INIT_RAM_END 0x00004000 /* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END \
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \
- GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_NS16550_MIN_FUNCTIONS
#endif
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */
-
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR + 0x4700)
#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR + 0x4800)
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER /* hush parser */
-#ifdef CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#endif
-
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED 400800 /* I2C speed and slave address*/
*/
/* eSPI - Enhanced SPI */
#ifdef CONFIG_FSL_ESPI
-#define CONFIG_CMD_SF
#define CONFIG_SF_DEFAULT_SPEED 10000000
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
#endif
#endif /* CONFIG_TSEC_ENET */
-#define CONFIG_MMC
#ifdef CONFIG_MMC
-#define CONFIG_CMD_MMC
-#define CONFIG_DOS_PARTITION
#define CONFIG_FSL_ESDHC
-#define CONFIG_GENERIC_MMC
#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
#endif
#define CONFIG_USB_EHCI /* USB */
#ifdef CONFIG_USB_EHCI
-#define CONFIG_CMD_USB
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
-#define CONFIG_USB_STORAGE
#define CONFIG_HAS_FSL_DR_USB
#endif
* Command line configuration.
*/
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
#define CONFIG_CMD_ERRATA
-#define CONFIG_CMD_I2C
#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
#define CONFIG_CMD_REGINFO
-#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI)
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_DOS_PARTITION
-#endif
-
/* Hash command with SHA acceleration supported in hardware */
#ifdef CONFIG_FSL_CAAM
#define CONFIG_CMD_HASH
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
-
/*
* For booting Linux, the board info and command line data
* have to be in the first 64 MB of memory, since this is
/*
* Dynamic MTD Partition support with mtdparts
*/
-#ifndef CONFIG_SYS_NO_FLASH
+#ifdef CONFIG_MTD_NOR_FLASH
#define CONFIG_MTD_DEVICE
#define CONFIG_MTD_PARTITIONS
#define CONFIG_CMD_MTDPARTS
"55m(fs),1m(uboot);ff800000.flash:1m(uboot)," \
"8m(kernel),512k(dtb),-(fs)"
#endif
-/*
- * Override partitions in device tree using info
- * in "mtdparts" environment variable
- */
-#ifdef CONFIG_CMD_MTDPARTS
-#define CONFIG_FDT_FIXUP_PARTITIONS
-#endif
-
/*
* Environment Configuration
*/
#define CONFIG_UBOOTPATH "u-boot.bin"
#define CONFIG_BAUDRATE 115200
-#define CONFIG_BOOTDELAY 10 /* -1 disable auto-boot */
#ifdef CONFIG_SDCARD
#define CONFIG_DEF_HWCONFIG "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0"
"consoledev=ttyS0\0" \
"ramdiskaddr=2000000\0" \
"ramdiskfile=rootfs.ext2.gz.uboot\0" \
- "fdtaddr=c00000\0" \
+ "fdtaddr=1e00000\0" \
"fdtfile=bsc9132qds.dtb\0" \
"bdev=sda1\0" \
CONFIG_DEF_HWCONFIG\
projects / people / ms / u-boot.git / blobdiff