Move CONFIG_OF_LIBFDT to Kconfig

[people/ms/u-boot.git] / include / configs / C29XPCIE.h

diff --git a/include/configs/C29XPCIE.h b/include/configs/C29XPCIE.h
index 7c45c3617ae4baf81aaeecc81d0cb294bcc65bde..6310e6364082fc3fb912bfe4743eaccab82c1403 100644 (file)
--- a/include/configs/C29XPCIE.h
+++ b/include/configs/C29XPCIE.h
@@ -12,7 +12,6 @@
 #define __CONFIG_H
 
 #define CONFIG_PHYS_64BIT
-#define CONFIG_SYS_GENERIC_BOARD
 #define CONFIG_DISPLAY_BOARDINFO
 
 #ifdef CONFIG_C29XPCIE
@@ -99,10 +98,8 @@
 #define CONFIG_FSL_PCIE_RESET          /* need PCIe reset errata */
 #define CONFIG_SYS_PCI_64BIT           /* enable 64-bit PCI resources */
 
-#define CONFIG_CMD_NET
 #define CONFIG_CMD_PCI
 
-#define CONFIG_E1000
 
 /*
  * PCI Windows
@@ -380,7 +377,6 @@
 
 /* Serial Port */
 #define CONFIG_CONS_INDEX      1
-#define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
 #define CONFIG_SYS_NS16550_CLK         get_bus_freq(0)
@@ -389,7 +385,6 @@
 #define CONFIG_NS16550_MIN_FUNCTIONS
 #endif
 
-#define CONFIG_SERIAL_MULTI            /* Enable both serial ports */
 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
 
 #define CONFIG_SYS_BAUDRATE_TABLE      \
@@ -404,7 +399,6 @@
 /*
  * Pass open firmware flat tree
  */
-#define CONFIG_OF_LIBFDT
 #define CONFIG_OF_BOARD_SETUP
 #define CONFIG_OF_STDOUT_VIA_ALIAS
 
@@ -424,7 +418,6 @@
 /* I2C EEPROM */
 /* enable read and write access to EEPROM */
 #define CONFIG_CMD_EEPROM
-#define CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
@@ -432,16 +425,11 @@
 #define CONFIG_CMD_I2C
 
 /* eSPI - Enhanced SPI */
-#define CONFIG_FSL_ESPI
-#define CONFIG_SPI_FLASH
-#define CONFIG_SPI_FLASH_SPANSION
-#define CONFIG_SPI_FLASH_EON
 #define CONFIG_CMD_SF
 #define CONFIG_SF_DEFAULT_SPEED                10000000
 #define CONFIG_SF_DEFAULT_MODE         SPI_MODE_0
 
 #ifdef CONFIG_TSEC_ENET
-#define CONFIG_NET_MULTI
 #define CONFIG_MII                     /* MII PHY management */
 #define CONFIG_MII_DEFAULT_TSEC        1       /* Allow unregistered phys */
 #define CONFIG_TSEC1           1
@@ -498,14 +486,10 @@
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
 #define CONFIG_CMD_ERRATA
-#define CONFIG_CMD_ELF
 #define CONFIG_CMD_IRQ
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_PING
-#define CONFIG_CMD_SETEXPR
 #define CONFIG_CMD_REGINFO
 
 /* Hash command with SHA acceleration supported in hardware */