* (easy to change)
***********************************************************/
#define CONFIG_405GP 1 /* This is a PPC405 CPU */
-#define CONFIG_MIP405 1 /* ...on a MIP405 board */
#define CONFIG_SYS_TEXT_BASE 0xFFF80000
-#define CONFIG_SYS_GENERIC_BOARD
-
/***********************************************************
* Note that it may also be a MIP405T board which is a subset of the
* MIP405
***********************************************************/
#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */
-
/*
* BOOTP options
*/
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
-
/*
* Command line configuration.
*/
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
#define CONFIG_CMD_IDE
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MII
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SAVES
-#define CONFIG_CMD_BSP
-
-#if !defined(CONFIG_MIP405T)
- #define CONFIG_CMD_USB
-#endif
-
-#define CONFIG_SYS_HUSH_PARSER
/**************************************************************
* I2C Stuff:
* the MIP405 is equiped with an Atmel 24C128/256 EEPROM at address
/* last 6 bits of the address */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
-
#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
#define CONFIG_ENV_OFFSET 0x00000 /* environment starts at the beginning of the EEPROM */
#define CONFIG_ENV_SIZE 0x00800 /* 2k bytes may be used for env vars */
/**************************************************************
* Environment definitions
**************************************************************/
-#define CONFIG_BAUDRATE 9600 /* STD Baudrate */
-#define CONFIG_BOOTDELAY 5
/* autoboot (do NOT change this set environment variable "bootdelay" to -1 instead) */
/* #define CONFIG_BOOT_RETRY_TIME -10 /XXX* feature is available but not enabled */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check console even if bootdelay = 0 */
#define CONFIG_BOOTCOMMAND "diskboot 400000 0:1; bootm" /* autoboot command */
#define CONFIG_BOOTARGS "console=ttyS0,9600 root=/dev/hda5" /* boot arguments */
#define CONFIG_IPADDR 10.0.0.100
#define CONFIG_SERVERIP 10.0.0.1
#define CONFIG_PREBOOT
-/***************************************************************
- * defines if the console is stored in the environment
- ***************************************************************/
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* stdin, stdout and stderr are in evironment */
/***************************************************************
* defines if an overwrite_console function exists
*************************************************************/
-#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
-#define CONFIG_SYS_CONSOLE_INFO_QUIET
/***************************************************************
* defines if the overwrite_console should be stored in the
* environment
**************************************************************/
-#undef CONFIG_SYS_CONSOLE_ENV_OVERWRITE
/**************************************************************
* loads config
#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 1 ... 12 MB in DRAM */
#define CONFIG_CONS_INDEX 1 /* Use UART0 */
-#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_serial_clock()
#define PCI_HOST_FORCE 1 /* configure as pci host */
#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-#define CONFIG_PCI /* include pci support */
#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
#define CONFIG_PCI_HOST PCI_HOST_FORCE /* configure as pci-host */
-#define CONFIG_PCI_PNP /* pci plug-and-play */
/* resource configuration */
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */
#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */
/* Size: 0=1MB, 1=2MB, 2=4MB, 3=8MB, 4=16MB, 5=32MB, 6=64MB, 7=128MB */
#define FLASH_SIZE_PRELIM 3 /* maximal flash FLASH size bank #0 */
-#define CONFIG_BOARD_EARLY_INIT_F 1
#define CONFIG_BOARD_EARLY_INIT_R
/* Peripheral Bus Mapping */
#define MULTI_PURPOSE_SOCKET_ADDR 0xF8000000
#define CONFIG_PORT_ADDR PER_PLD_ADDR + 5
-
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in On Chip SRAM)
*/
/************************************************************
* IDE/ATA stuff
************************************************************/
-#if defined(CONFIG_MIP405T)
+#if defined(CONFIG_TARGET_MIP405T)
#define CONFIG_SYS_IDE_MAXBUS 1 /* MIP405T has only one IDE bus */
#else
#define CONFIG_SYS_IDE_MAXBUS 2 /* max. 2 IDE busses */
/************************************************************
* DISK Partition support
************************************************************/
-#define CONFIG_DOS_PARTITION
-#define CONFIG_MAC_PARTITION
-#define CONFIG_ISO_PARTITION /* Experimental */
-
-/************************************************************
- * Keyboard support
- ************************************************************/
-#undef CONFIG_ISA_KEYBOARD
/************************************************************
* Video support
************************************************************/
-#define CONFIG_VIDEO /*To enable video controller support */
-#define CONFIG_VIDEO_CT69000
-#define CONFIG_CFB_CONSOLE
#define CONFIG_VIDEO_LOGO
-#define CONFIG_CONSOLE_EXTRA_INFO
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_VIDEO_SW_CURSOR
#undef CONFIG_VIDEO_ONBOARD
/************************************************************
* USB support EXPERIMENTAL
************************************************************/
-#if !defined(CONFIG_MIP405T)
+#if !defined(CONFIG_TARGET_MIP405T)
#define CONFIG_USB_UHCI
-#define CONFIG_USB_KEYBOARD
-#define CONFIG_USB_STORAGE
/* Enable needed helper functions */
-#define CONFIG_SYS_STDIO_DEREGISTER /* needs stdio_deregister */
#endif
/************************************************************
* Debug support
************************************************************/
#define CONFIG_BZIP2 1
-/************************************************************
- * Ident
- ************************************************************/
-
-#define VERSION_TAG "released"
-#if !defined(CONFIG_MIP405T)
-#define CONFIG_ISO_STRING "MEV-10072-001"
-#else
-#define CONFIG_ISO_STRING "MEV-10082-001"
-#endif
-
-#if !defined(CONFIG_BOOT_PCI)
-#define CONFIG_IDENT_STRING "\n(c) 2003 by MPL AG Switzerland, " CONFIG_ISO_STRING " " VERSION_TAG
-#else
-#define CONFIG_IDENT_STRING "\n(c) 2003 by MPL AG Switzerland, PCI_BOOT Version"
-#endif
-
-
#endif /* __CONFIG_H */
projects / people / ms / u-boot.git / blobdiff