Move CONFIG_OF_LIBFDT to Kconfig

[people/ms/u-boot.git] / include / configs / MPC8540ADS.h

diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h
index acd37a01aa75ca4c5dbffbf64c8da34531f74d92..d616c0f3fd772ccffbf60460cb7b99a8e4a321da 100644 (file)
--- a/include/configs/MPC8540ADS.h
+++ b/include/configs/MPC8540ADS.h
@@ -3,7 +3,7 @@
  * (C) Copyright 2002,2003 Motorola,Inc.
  * Xianghua Xiao <X.Xiao@motorola.com>
  *
- * SPDX-License-Identifier:    GPL-2.0+ 
+ * SPDX-License-Identifier:    GPL-2.0+
  */
 
 /*
@@ -12,16 +12,17 @@
  * Please refer to doc/README.mpc85xx for more info.
  *
  * Make sure you change the MAC address and other network params first,
- * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file.
+ * search for CONFIG_SERVERIP, etc in this file.
  */
 
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
+#define CONFIG_DISPLAY_BOARDINFO
+
 /* High Level Configuration Options */
 #define CONFIG_BOOKE           1       /* BOOKE */
 #define CONFIG_E500            1       /* BOOKE e500 family */
-#define CONFIG_MPC85xx         1       /* MPC8540/MPC8560 */
 #define CONFIG_MPC8540         1       /* MPC8540 specific */
 #define CONFIG_MPC8540ADS      1       /* MPC8540ADS board specific */
 
@@ -78,7 +79,7 @@
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW    CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR1
+#define CONFIG_SYS_FSL_DDR1
 #define CONFIG_SPD_EEPROM              /* Use SPD EEPROM for DDR setup*/
 #define CONFIG_DDR_SPD
 #undef CONFIG_FSL_DDR_INTERACTIVE
@@ -220,7 +221,6 @@
 
 /* Serial Port */
 #define CONFIG_CONS_INDEX     1
-#define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
 #define CONFIG_SYS_NS16550_CLK         get_bus_freq(0)
@@ -237,7 +237,6 @@
 #endif
 
 /* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT               1
 #define CONFIG_OF_BOARD_SETUP          1
 #define CONFIG_OF_STDOUT_VIA_ALIAS     1
 
@@ -349,24 +348,14 @@
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_I2C
-#define CONFIG_CMD_ELF
 #define CONFIG_CMD_IRQ
-#define CONFIG_CMD_SETEXPR
 
 #if defined(CONFIG_PCI)
     #define CONFIG_CMD_PCI
 #endif
 
-#if defined(CONFIG_SYS_RAMBOOT)
-    #undef CONFIG_CMD_SAVEENV
-    #undef CONFIG_CMD_LOADS
-#endif
-
-
 #undef CONFIG_WATCHDOG                 /* watchdog disabled */
 
 /*
@@ -376,7 +365,6 @@
 #define CONFIG_CMDLINE_EDITING                 /* Command-line editing */
 #define CONFIG_AUTO_COMPLETE                   /* add autocompletion support */
 #define CONFIG_SYS_LOAD_ADDR   0x2000000       /* default load address */
-#define CONFIG_SYS_PROMPT      "=> "           /* Monitor Command Prompt */
 
 #if defined(CONFIG_CMD_KGDB)
     #define CONFIG_SYS_CBSIZE  1024            /* Console I/O Buffer Size */
@@ -387,7 +375,6 @@
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 #define CONFIG_SYS_MAXARGS     16              /* max number of command args */
 #define CONFIG_SYS_BARGSIZE    CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size */
-#define CONFIG_SYS_HZ          1000            /* decrementer freq: 1ms ticks */
 
 /*
  * For booting Linux, the board info and command line data
@@ -399,7 +386,6 @@
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX  2       /* which serial port to use */
 #endif
 
 
@@ -410,11 +396,8 @@
 /* The mac addresses for all ethernet interface */
 #if defined(CONFIG_TSEC_ENET)
 #define CONFIG_HAS_ETH0
-#define CONFIG_ETHADDR   00:E0:0C:00:00:FD
 #define CONFIG_HAS_ETH1
-#define CONFIG_ETH1ADDR  00:E0:0C:00:01:FD
 #define CONFIG_HAS_ETH2
-#define CONFIG_ETH2ADDR  00:E0:0C:00:02:FD
 #endif
 
 #define CONFIG_IPADDR    192.168.1.253