drivers/pci/Kconfig: Add PCI

[people/ms/u-boot.git] / include / configs / MPC8560ADS.h

diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h
index bb9ae2dcb53438ba9c6d76b1f9353bcc674d6678..e58987efe520c7458d71d79fd5564047cdc9399f 100644 (file)
--- a/include/configs/MPC8560ADS.h
+++ b/include/configs/MPC8560ADS.h
@@ -12,7 +12,7 @@
  * Please refer to doc/README.mpc85xx for more info.
  *
  * Make sure you change the MAC address and other network params first,
- * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file.
+ * search for CONFIG_SERVERIP, etc. in this file.
  */
 
 #ifndef __CONFIG_H
@@ -21,7 +21,6 @@
 /* High Level Configuration Options */
 #define CONFIG_BOOKE           1       /* BOOKE */
 #define CONFIG_E500            1       /* BOOKE e500 family */
-#define CONFIG_MPC85xx         1       /* MPC8540/MPC8560 */
 #define CONFIG_CPM2            1       /* has CPM2 */
 #define CONFIG_MPC8560ADS      1       /* MPC8560ADS board specific */
 #define CONFIG_MPC8560         1
@@ -32,7 +31,6 @@
  */
 #define        CONFIG_SYS_TEXT_BASE    0xfff80000
 
-#define CONFIG_PCI
 #define CONFIG_PCI_INDIRECT_BRIDGE
 #define CONFIG_SYS_PCI_64BIT   1       /* enable 64-bit PCI resources */
 #define CONFIG_TSEC_ENET               /* tsec ethernet support */
@@ -59,7 +57,6 @@
 #define CONFIG_SYS_CLK_FREQ    33000000
 #endif
 
-
 /*
  * These can be toggled for performance analysis, otherwise use default.
  */
@@ -132,7 +129,6 @@
 
 #undef CONFIG_CLOCKS_IN_MHZ
 
-
 /*
  * Local Bus Definitions
  */
@@ -197,7 +193,6 @@
 #define CONFIG_SYS_LBC_LSDMR_4 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW)
 #define CONFIG_SYS_LBC_LSDMR_5 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL)
 
-
 /*
  * 32KB, 8-bit wide for ADS config reg
  */
@@ -225,16 +220,6 @@
 #define CONFIG_SYS_BAUDRATE_TABLE  \
        {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-#ifdef  CONFIG_SYS_HUSH_PARSER
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT               1
-#define CONFIG_OF_BOARD_SETUP          1
-#define CONFIG_OF_STDOUT_VIA_ALIAS     1
-
 /*
  * I2C
  */
@@ -282,7 +267,6 @@
 
 #endif /* CONFIG_PCI */
 
-
 #ifdef CONFIG_TSEC_ENET
 
 #ifndef CONFIG_MII
@@ -354,7 +338,6 @@
 
 #endif
 
-
 /*
  * Environment
  */
@@ -381,17 +364,10 @@
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 
-
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_ELF
 #define CONFIG_CMD_IRQ
-#define CONFIG_CMD_SETEXPR
 #define CONFIG_CMD_REGINFO
 
 #if defined(CONFIG_PCI)
@@ -399,15 +375,8 @@
 #endif
 
 #if defined(CONFIG_ETHER_ON_FCC)
-    #define CONFIG_CMD_MII
-#endif
-
-#if defined(CONFIG_SYS_RAMBOOT)
-    #undef CONFIG_CMD_SAVEENV
-    #undef CONFIG_CMD_LOADS
 #endif
 
-
 #undef CONFIG_WATCHDOG                 /* watchdog disabled */
 
 /*
@@ -438,24 +407,16 @@
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX  2       /* which serial port to use */
 #endif
 
-
 /*
  * Environment Configuration
  */
-
-/* The mac addresses for all ethernet interface */
 #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
 #define CONFIG_HAS_ETH0
-#define CONFIG_ETHADDR   00:E0:0C:00:00:FD
 #define CONFIG_HAS_ETH1
-#define CONFIG_ETH1ADDR  00:E0:0C:00:01:FD
 #define CONFIG_HAS_ETH2
-#define CONFIG_ETH2ADDR  00:E0:0C:00:02:FD
 #define CONFIG_HAS_ETH3
-#define CONFIG_ETH3ADDR  00:E0:0C:00:03:FD
 #endif
 
 #define CONFIG_IPADDR    192.168.1.253
@@ -470,7 +431,6 @@
 
 #define CONFIG_LOADADDR  200000        /* default location for tftp and bootm */
 
-#define CONFIG_BOOTDELAY 10    /* -1 disables auto-boot */
 #undef  CONFIG_BOOTARGS                /* the boot command will set bootargs */
 
 #define CONFIG_BAUDRATE        115200