/*
- * Copyright 2004-2007 Freescale Semiconductor.
+ * Copyright 2004-2007, 2010-2011 Freescale Semiconductor.
*
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * SPDX-License-Identifier: GPL-2.0+
*/
/*
#ifndef __CONFIG_H
#define __CONFIG_H
+#define CONFIG_DISPLAY_BOARDINFO
+
/* High Level Configuration Options */
#define CONFIG_BOOKE 1 /* BOOKE */
#define CONFIG_E500 1 /* BOOKE e500 family */
-#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48/68 */
#define CONFIG_MPC8568 1 /* MPC8568 specific */
#define CONFIG_MPC8568MDS 1 /* MPC8568MDS board specific */
#define CONFIG_SYS_TEXT_BASE 0xfff80000
+#define CONFIG_SYS_SRIO
+#define CONFIG_SRIO1 /* SRIO port 1 */
+
#define CONFIG_PCI 1 /* Enable PCI/PCIE */
#define CONFIG_PCI1 1 /* PCI controller */
#define CONFIG_PCIE1 1 /* PCIE controller */
#define CONFIG_FSL_PCI_INIT 1 /* use common fsl pci init code */
+#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00400000
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
-#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR 0xe0000000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_SPD
-#define CONFIG_DDR_DLL /* possible DLL fix needed */
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
/* Serial Port */
#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
/* Use the HUSH parser*/
#define CONFIG_SYS_HUSH_PARSER
#ifdef CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#endif
/* pass open firmware flat tree */
/*
* I2C
*/
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
/*
* General PCI
#define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000
#define CONFIG_SYS_PCI1_IO_SIZE 0x00800000 /* 8M */
+#define CONFIG_SYS_PCIE1_NAME "Slot"
#define CONFIG_SYS_PCIE1_MEM_VIRT 0xa0000000
#define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xa0000000
#define CONFIG_SYS_PCIE1_IO_PHYS 0xe2800000
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */
-#define CONFIG_SYS_SRIO_MEM_VIRT 0xc0000000
-#define CONFIG_SYS_SRIO_MEM_BUS 0xc0000000
-#define CONFIG_SYS_SRIO_MEM_PHYS 0xc0000000
+#define CONFIG_SYS_SRIO1_MEM_VIRT 0xC0000000
+#define CONFIG_SYS_SRIO1_MEM_BUS 0xC0000000
+#define CONFIG_SYS_SRIO1_MEM_PHYS CONFIG_SYS_SRIO1_MEM_BUS
+#define CONFIG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 512M */
#ifdef CONFIG_QE
/*
#define CONFIG_SYS_UEC1_TX_CLK QE_CLK16
#define CONFIG_SYS_UEC1_ETH_TYPE GIGA_ETH
#define CONFIG_SYS_UEC1_PHY_ADDR 7
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE RGMII_ID
+#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
#define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000
#endif
#define CONFIG_SYS_UEC2_TX_CLK QE_CLK16
#define CONFIG_SYS_UEC2_ETH_TYPE GIGA_ETH
#define CONFIG_SYS_UEC2_PHY_ADDR 1
-#define CONFIG_SYS_UEC2_INTERFACE_TYPE RGMII_ID
+#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
#define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000
#endif
#endif /* CONFIG_QE */
#if defined(CONFIG_PCI)
-#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#undef CONFIG_EEPRO100
#endif /* CONFIG_PCI */
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI 1
-#endif
-
#if defined(CONFIG_TSEC_ENET)
#define CONFIG_MII 1 /* MII PHY management */
/*
* Command line configuration.
*/
-#include <config_cmd_default.h>
-
#define CONFIG_CMD_PING
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
-#define CONFIG_CMD_ELF
#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_SETEXPR
#define CONFIG_CMD_REGINFO
#if defined(CONFIG_PCI)
#define CONFIG_CMDLINE_EDITING /* Command-line editing */
#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
/*
* For booting Linux, the board info and command line data
- * have to be in the first 16 MB of memory, since this is
+ * have to be in the first 64 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/*
/* The mac addresses for all ethernet interface */
#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_UEC_ETH)
#define CONFIG_HAS_ETH0
-#define CONFIG_ETHADDR 00:E0:0C:00:00:FD
#define CONFIG_HAS_ETH1
-#define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD
#define CONFIG_HAS_ETH2
-#define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD
#define CONFIG_HAS_ETH3
-#define CONFIG_ETH3ADDR 00:E0:0C:00:03:FD
#endif
#define CONFIG_IPADDR 192.168.1.253
#define CONFIG_HOSTNAME unknown
-#define CONFIG_ROOTPATH /nfsroot
-#define CONFIG_BOOTFILE your.uImage
+#define CONFIG_ROOTPATH "/nfsroot"
+#define CONFIG_BOOTFILE "your.uImage"
#define CONFIG_SERVERIP 192.168.1.1
#define CONFIG_GATEWAYIP 192.168.1.1
projects / people / ms / u-boot.git / blobdiff