configs: Migrate CONFIG_SYS_TEXT_BASE

[people/ms/u-boot.git] / include / configs / MPC8610HPCD.h

diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h
index 2529d8a71e2d2fc8b9ac6f45e4957c41ca6733f3..3eaa4630f81615010a4f2bc8ce630cc070240fd4 100644 (file)
--- a/include/configs/MPC8610HPCD.h
+++ b/include/configs/MPC8610HPCD.h
@@ -12,18 +12,13 @@
 #define __CONFIG_H
 
 /* High Level Configuration Options */
-#define CONFIG_MPC8610         1       /* MPC8610 specific */
-#define CONFIG_MPC8610HPCD     1       /* MPC8610HPCD board specific */
 #define CONFIG_LINUX_RESET_VEC 0x100   /* Reset vector used by Linux */
 
-#define        CONFIG_SYS_TEXT_BASE    0xfff00000
-
 /* video */
 #define CONFIG_FSL_DIU_FB
 
 #ifdef CONFIG_FSL_DIU_FB
 #define CONFIG_SYS_DIU_ADDR    (CONFIG_SYS_CCSRBAR + 0x2c000)
-#define CONFIG_CMD_BMP
 #define CONFIG_VIDEO_LOGO
 #define CONFIG_VIDEO_BMP_LOGO
 #endif
@@ -44,7 +39,6 @@
 #define CONFIG_FSL_PCI_INIT    1       /* Use common FSL init code */
 #define CONFIG_PCI_INDIRECT_BRIDGE 1   /* indirect PCI bridge support */
 #define CONFIG_SYS_PCI_64BIT   1       /* enable 64-bit PCI resources */
-#define CONFIG_FSL_LAW         1       /* Use common FSL init code */
 
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_INTERRUPTS              /* enable pci, srio, ddr interrupts */
@@ -64,7 +58,6 @@
 #define CONFIG_SYS_CLK_FREQ    get_board_sys_clk(0)
 #endif
 
-#define CONFIG_BOARD_EARLY_INIT_F      1       /* Call board_pre_init */
 #define CONFIG_MISC_INIT_R             1
 
 #define CONFIG_SYS_MEMTEST_START       0x00200000      /* memtest region */
@@ -74,7 +67,6 @@
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  */
-#define CONFIG_SYS_CCSRBAR_DEFAULT     0xff700000      /* CCSRBAR Default */
 #define CONFIG_SYS_CCSRBAR             0xe0000000      /* relocated CCSRBAR */
 #define CONFIG_SYS_IMMR                CONFIG_SYS_CCSRBAR      /* PQII uses CONFIG_SYS_IMMR */
 
@@ -83,7 +75,6 @@
 #define CONFIG_SYS_CCSRBAR_PHYS                CONFIG_SYS_CCSRBAR_PHYS_LOW
 
 /* DDR Setup */
-#define CONFIG_SYS_FSL_DDR2
 #undef CONFIG_FSL_DDR_INTERACTIVE
 #define CONFIG_SPD_EEPROM              /* Use SPD for DDR */
 #define CONFIG_DDR_SPD
@@ -96,7 +87,6 @@
 #define CONFIG_SYS_MAX_DDR_BAT_SIZE    0x80000000      /* BAT mapping size */
 #define CONFIG_VERY_BIG_RAM
 
-#define CONFIG_NUM_DDR_CONTROLLERS     1
 #define CONFIG_DIMM_SLOTS_PER_CTLR     1
 #define CONFIG_CHIP_SELECTS_PER_CTRL   (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
 
@@ -270,8 +260,6 @@
 
 #define CONFIG_PCI_SCAN_SHOW           /* show pci devices on startup */
 
-#define CONFIG_CMD_REGINFO
-
 #define CONFIG_ULI526X
 #ifdef CONFIG_ULI526X
 #endif
@@ -281,7 +269,6 @@
  ************************************************************/
 #define CONFIG_PCI_OHCI                1
 #define CONFIG_USB_OHCI_NEW            1
-#define CONFIG_SYS_USB_EVENT_POLL      1
 #define CONFIG_SYS_USB_OHCI_SLOT_NAME  "ohci_pci"
 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
 #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS        1
@@ -292,11 +279,7 @@
 #define PCI_IDSEL_NUMBER       0x0c    /* slot0->3(IDSEL)=12->15 */
 #endif
 
-#define CONFIG_DOS_PARTITION
-#define CONFIG_SCSI_AHCI
-
 #ifdef CONFIG_SCSI_AHCI
-#define CONFIG_LIBATA
 #define CONFIG_SATA_ULI5288
 #define CONFIG_SYS_SCSI_MAX_SCSI_ID    4
 #define CONFIG_SYS_SCSI_MAX_LUN        1
@@ -412,12 +395,10 @@
  * Environment
  */
 #ifndef CONFIG_SYS_RAMBOOT
-#define CONFIG_ENV_IS_IN_FLASH 1
 #define CONFIG_ENV_ADDR                (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 #define CONFIG_ENV_SECT_SIZE   0x20000 /* 126k (one sector) for env */
 #define CONFIG_ENV_SIZE                0x2000
 #else
-#define CONFIG_ENV_IS_NOWHERE  1       /* Store ENV in memory only */
 #define CONFIG_ENV_ADDR                (CONFIG_SYS_MONITOR_BASE - 0x1000)
 #define CONFIG_ENV_SIZE                0x2000
 #endif
@@ -437,11 +418,6 @@
  * Command line configuration.
  */
 
-#if defined(CONFIG_PCI)
-#define CONFIG_CMD_PCI
-#define CONFIG_SCSI
-#endif
-
 #define CONFIG_WATCHDOG                        /* watchdog enabled */
 #define CONFIG_SYS_WATCHDOG_FREQ       5000    /* Feed interval, 5s */
 
@@ -452,16 +428,6 @@
 #define CONFIG_CMDLINE_EDITING          /* Command-line editing */
 #define CONFIG_SYS_LOAD_ADDR   0x2000000       /* default load address */
 
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE      1024            /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE      256             /* Console I/O Buffer Size */
-#endif
-
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS     16              /* max number of command args */
-#define CONFIG_SYS_BARGSIZE    CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size */
-
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
@@ -491,10 +457,6 @@
 /* default location for tftp and bootm */
 #define CONFIG_LOADADDR                0x10000000
 
-#undef CONFIG_BOOTARGS         /* the boot command will set bootargs */
-
-#define CONFIG_BAUDRATE        115200
-
 #if defined(CONFIG_PCI1)
 #define PCI_ENV \
  "pcireg=md ${a}000 3; echo o;md ${a}c00 25; echo i; md ${a}da0 15;" \