#define CONFIG_NAND_LEGACY
-#define CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
/**************************************************************
* I2C Stuff:
* the PIP405 is equiped with an Atmel 24C128/256 EEPROM at address
* The Atmel EEPROM uses 16Bit addressing.
***************************************************************/
#define CONFIG_HARD_I2C /* I2c with hardware support */
-#define CFG_I2C_SPEED 50000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_SPEED 50000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CFG_I2C_EEPROM_ADDR 0x53
-#define CFG_I2C_EEPROM_ADDR_LEN 2
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x53
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
#define CONFIG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
#define CONFIG_ENV_SIZE 0x800 /* 2 kBytes may be used for env vars */
-#undef CFG_I2C_EEPROM_ADDR_OVERFLOW
-#define CFG_EEPROM_PAGE_WRITE_BITS 6 /* The Atmel 24C128/256 has */
+#undef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* The Atmel 24C128/256 has */
/* 64 byte page write mode using*/
/* last 6 bits of the address */
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
/***************************************************************
/***************************************************************
* defines if the console is stored in the environment
***************************************************************/
-#define CFG_CONSOLE_IS_IN_ENV /* stdin, stdout and stderr are in evironment */
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* stdin, stdout and stderr are in evironment */
/***************************************************************
* defines if an overwrite_console function exists
*************************************************************/
-#define CFG_CONSOLE_OVERWRITE_ROUTINE
-#define CFG_CONSOLE_INFO_QUIET
+#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
+#define CONFIG_SYS_CONSOLE_INFO_QUIET
/***************************************************************
* defines if the overwrite_console should be stored in the
* environment
**************************************************************/
-#undef CFG_CONSOLE_ENV_OVERWRITE
+#undef CONFIG_SYS_CONSOLE_ENV_OVERWRITE
/**************************************************************
* loads config
*************************************************************/
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MISC_INIT_R
/***********************************************************
* Miscellaneous configurable options
**********************************************************/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x0100000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 1 ... 12 MB in DRAM */
+#define CONFIG_SYS_MEMTEST_START 0x0100000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 1 ... 12 MB in DRAM */
-#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
-#define CFG_BASE_BAUD 691200
+#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */
+#define CONFIG_SYS_BASE_BAUD 691200
/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
+#define CONFIG_SYS_BAUDRATE_TABLE \
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
57600, 115200, 230400, 460800, 921600 }
-#define CFG_LOAD_ADDR 0x400000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+#define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */
+#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
/*-----------------------------------------------------------------------
* PCI stuff
#define CONFIG_PCI_HOST PCI_HOST_FORCE /* configure as pci-host */
#define CONFIG_PCI_PNP /* pci plug-and-play */
/* resource configuration */
-#define CFG_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */
-#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CFG_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CFG_PCI_PTM2LA 0x00000000 /* disabled */
-#define CFG_PCI_PTM2MS 0x00000000 /* disabled */
-#define CFG_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */
+#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */
+#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */
+#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */
+#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */
+#define CONFIG_SYS_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_FLASH_BASE 0xFFF80000
-#define CFG_MONITOR_BASE CFG_FLASH_BASE
-#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */
-#define CFG_MALLOC_LEN (1024 * 1024) /* Reserve 1024 kB for malloc() */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_FLASH_BASE 0xFFF80000
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserve 1024 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
/*
* Init Memory Controller:
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in On Chip SRAM)
*/
-#define CFG_TEMP_STACK_OCM 1
-#define CFG_OCM_DATA_ADDR 0xF0000000
-#define CFG_OCM_DATA_SIZE 0x1000
-#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of On Chip SRAM */
-#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of On Chip SRAM */
-#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_TEMP_STACK_OCM 1
+#define CONFIG_SYS_OCM_DATA_ADDR 0xF0000000
+#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of On Chip SRAM */
+#define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE /* End of On Chip SRAM */
+#define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*
* Internal Definitions
/***********************************************************************
* External peripheral base address
***********************************************************************/
-#define CFG_ISA_IO_BASE_ADDRESS 0xE8000000
+#define CONFIG_SYS_ISA_IO_BASE_ADDRESS 0xE8000000
/***********************************************************************
* Last Stage Init
/************************************************************
* IDE/ATA stuff
************************************************************/
-#define CFG_IDE_MAXBUS 2 /* max. 2 IDE busses */
-#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
+#define CONFIG_SYS_IDE_MAXBUS 2 /* max. 2 IDE busses */
+#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
-#define CFG_ATA_BASE_ADDR CFG_ISA_IO_BASE_ADDRESS /* base address */
-#define CFG_ATA_IDE0_OFFSET 0x01F0 /* ide0 offste */
-#define CFG_ATA_IDE1_OFFSET 0x0170 /* ide1 offset */
-#define CFG_ATA_DATA_OFFSET 0 /* data reg offset */
-#define CFG_ATA_REG_OFFSET 0 /* reg offset */
-#define CFG_ATA_ALT_OFFSET 0x200 /* alternate register offset */
+#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_ISA_IO_BASE_ADDRESS /* base address */
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x01F0 /* ide0 offste */
+#define CONFIG_SYS_ATA_IDE1_OFFSET 0x0170 /* ide1 offset */
+#define CONFIG_SYS_ATA_DATA_OFFSET 0 /* data reg offset */
+#define CONFIG_SYS_ATA_REG_OFFSET 0 /* reg offset */
+#define CONFIG_SYS_ATA_ALT_OFFSET 0x200 /* alternate register offset */
#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
#undef CONFIG_IDE_LED /* no led for ide supported */
* SCSI support (experimental) only SYM53C8xx supported
************************************************************/
#define CONFIG_SCSI_SYM53C8XX
-#define CFG_SCSI_MAX_LUN 8 /* number of supported LUNs */
-#define CFG_SCSI_MAX_SCSI_ID 7 /* maximum SCSI ID (0..6) */
-#define CFG_SCSI_MAX_DEVICE CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN /* maximum Target devices */
-#define CFG_SCSI_SPIN_UP_TIME 2
+#define CONFIG_SYS_SCSI_MAX_LUN 8 /* number of supported LUNs */
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID 7 /* maximum SCSI ID (0..6) */
+#define CONFIG_SYS_SCSI_MAX_DEVICE CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN /* maximum Target devices */
+#define CONFIG_SYS_SCSI_SPIN_UP_TIME 2
/************************************************************
* Disk-On-Chip configuration
************************************************************/
-#define CFG_MAX_DOC_DEVICE 1 /* Max number of DOC devices */
-#define CFG_DOC_SHORT_TIMEOUT
-#define CFG_DOC_SUPPORT_2000
-#define CFG_DOC_SUPPORT_MILLENNIUM
+#define CONFIG_SYS_MAX_DOC_DEVICE 1 /* Max number of DOC devices */
+#define CONFIG_SYS_DOC_SHORT_TIMEOUT
+#define CONFIG_SYS_DOC_SUPPORT_2000
+#define CONFIG_SYS_DOC_SUPPORT_MILLENNIUM
/************************************************************
* DISK Partition support
#define CONFIG_USB_STORAGE
/* Enable needed helper functions */
-#define CFG_DEVICE_DEREGISTER /* needs device_deregister */
+#define CONFIG_SYS_DEVICE_DEREGISTER /* needs device_deregister */
/************************************************************
* Debug support
projects / people / ms / u-boot.git / blobdiff