common: Add DISPLAY_BOARDINFO

[people/ms/u-boot.git] / include / configs / T102xQDS.h

diff --git a/include/configs/T102xQDS.h b/include/configs/T102xQDS.h
index 0fa03cf93cd652af6ecc58dfe334c90941309d63..f24e902de303575d38538ecb256fb0cb24caa1b3 100644 (file)
--- a/include/configs/T102xQDS.h
+++ b/include/configs/T102xQDS.h
@@ -12,14 +12,11 @@
 #define __T1024QDS_H
 
 /* High Level Configuration Options */
-#define CONFIG_SYS_GENERIC_BOARD
-#define CONFIG_DISPLAY_BOARDINFO
 #define CONFIG_BOOKE
 #define CONFIG_E500                    /* BOOKE e500 family */
 #define CONFIG_E500MC                  /* BOOKE e500mc family */
 #define CONFIG_SYS_BOOK3E_HV           /* Category E.HV supported */
 #define CONFIG_MP                      /* support multiple processors */
-#define CONFIG_PHYS_64BIT
 #define CONFIG_ENABLE_36BIT_PHYS
 
 #ifdef CONFIG_PHYS_64BIT
@@ -40,18 +37,13 @@
 #define CONFIG_BOARD_EARLY_INIT_F
 #endif
 
+#define CONFIG_FSL_CAAM                        /* Enable SEC/CAAM */
+
 #ifdef CONFIG_RAMBOOT_PBL
 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t102xqds/t1024_pbi.cfg
 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xqds/t1024_rcw.cfg
-#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
-#define CONFIG_SPL_ENV_SUPPORT
-#define CONFIG_SPL_SERIAL_SUPPORT
 #define CONFIG_SPL_FLUSH_IMAGE
 #define CONFIG_SPL_TARGET              "u-boot-with-spl.bin"
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_I2C_SUPPORT
-#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
 #define CONFIG_FSL_LAW                 /* Use common FSL init code */
 #define CONFIG_SYS_TEXT_BASE           0x00201000
 #define CONFIG_SPL_TEXT_BASE           0xFFFD8000
@@ -67,7 +59,6 @@
 #endif
 
 #ifdef CONFIG_NAND
-#define CONFIG_SPL_NAND_SUPPORT
 #define CONFIG_SYS_NAND_U_BOOT_SIZE    (768 << 10)
 #define CONFIG_SYS_NAND_U_BOOT_DST     0x00200000
 #define CONFIG_SYS_NAND_U_BOOT_START   0x00200000
@@ -78,8 +69,6 @@
 
 #ifdef CONFIG_SPIFLASH
 #define CONFIG_RESET_VECTOR_ADDRESS            0x200FFC
-#define CONFIG_SPL_SPI_SUPPORT
-#define CONFIG_SPL_SPI_FLASH_SUPPORT
 #define CONFIG_SPL_SPI_FLASH_MINIMAL
 #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE       (768 << 10)
 #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST                (0x00200000)
@@ -94,7 +83,6 @@
 
 #ifdef CONFIG_SDCARD
 #define CONFIG_RESET_VECTOR_ADDRESS            0x200FFC
-#define CONFIG_SPL_MMC_SUPPORT
 #define CONFIG_SPL_MMC_MINIMAL
 #define CONFIG_SYS_MMC_U_BOOT_SIZE     (768 << 10)
 #define CONFIG_SYS_MMC_U_BOOT_DST      (0x00200000)
@@ -201,7 +189,6 @@
 #define CONFIG_ENV_SECT_SIZE   0x20000 /* 128K (one sector) */
 #endif
 
-
 #ifndef __ASSEMBLY__
 unsigned long get_board_sys_clk(void);
 unsigned long get_board_ddr_clk(void);
@@ -475,13 +462,13 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_INIT_RAM_ADDR       0xfdd00000      /* Initial L1 address */
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH     0xf
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW      0xfe0ec000
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW      0xfe03c000
 /* The assembler doesn't like typecast */
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
        ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
          CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 #else
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS  0xfe0ec000 /* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS  0xfe03c000 /* Initial L1 address */
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
 #endif
@@ -496,7 +483,6 @@ unsigned long get_board_ddr_clk(void);
 
 /* Serial Port */
 #define CONFIG_CONS_INDEX      1
-#define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
 #define CONFIG_SYS_NS16550_CLK         (get_bus_freq(0)/2)
@@ -510,10 +496,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_NS16550_COM4        (CONFIG_SYS_CCSRBAR+0x11D600)
 #define CONFIG_SYS_CONSOLE_IS_IN_ENV   /* determine from environment */
 
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-
 /* Video */
 #ifdef CONFIG_PPC_T1024                /* no DIU on T1023 */
 #define CONFIG_FSL_DIU_FB
@@ -536,15 +518,6 @@ unsigned long get_board_ddr_clk(void);
 #endif
 #endif
 
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_OF_STDOUT_VIA_ALIAS
-
-/* new uImage format support */
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE     /* enable fit_format_{error,warning}() */
-
 /* I2C */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_FSL             /* Use FSL common I2C driver */
@@ -580,13 +553,8 @@ unsigned long get_board_ddr_clk(void);
 /*
  * eSPI - Enhanced SPI
  */
-#define CONFIG_FSL_ESPI
-#define CONFIG_SPI_FLASH_STMICRO
 #ifndef CONFIG_SPL_BUILD
-#define CONFIG_SPI_FLASH_SST
-#define CONFIG_SPI_FLASH_EON
 #endif
-#define CONFIG_CMD_SF
 #define CONFIG_SPI_FLASH_BAR
 #define CONFIG_SF_DEFAULT_SPEED         10000000
 #define CONFIG_SF_DEFAULT_MODE   0
@@ -596,9 +564,9 @@ unsigned long get_board_ddr_clk(void);
  * Memory space is mapped 1-1, but I/O space must start from 0.
  */
 #define CONFIG_PCI             /* Enable PCI/PCIE */
-#define CONFIG_PCIE1           /* PCIE controler 1 */
-#define CONFIG_PCIE2           /* PCIE controler 2 */
-#define CONFIG_PCIE3           /* PCIE controler 3 */
+#define CONFIG_PCIE1           /* PCIE controller 1 */
+#define CONFIG_PCIE2           /* PCIE controller 2 */
+#define CONFIG_PCIE3           /* PCIE controller 3 */
 #define CONFIG_FSL_PCI_INIT    /* Use common FSL init code */
 #define CONFIG_SYS_PCI_64BIT   /* enable 64-bit PCI resources */
 #define CONFIG_PCI_INDIRECT_BRIDGE
@@ -668,7 +636,6 @@ unsigned long get_board_ddr_clk(void);
 #endif
 
 #define CONFIG_PCI_PNP                 /* do pci plug-and-play */
-#define CONFIG_E1000
 #define CONFIG_PCI_SCAN_SHOW           /* show pci devices on startup */
 #define CONFIG_DOS_PARTITION
 #endif /* CONFIG_PCI */
@@ -687,7 +654,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_LBA48
 #define CONFIG_CMD_SATA
 #define CONFIG_DOS_PARTITION
-#define CONFIG_CMD_EXT2
 #endif
 
 /*
@@ -697,11 +663,8 @@ unsigned long get_board_ddr_clk(void);
 
 #ifdef CONFIG_HAS_FSL_DR_USB
 #define CONFIG_USB_EHCI
-#define CONFIG_CMD_USB
-#define CONFIG_USB_STORAGE
 #define CONFIG_USB_EHCI_FSL
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_CMD_EXT2
 #endif
 
 /*
@@ -711,10 +674,7 @@ unsigned long get_board_ddr_clk(void);
 #ifdef CONFIG_MMC
 #define CONFIG_FSL_ESDHC
 #define CONFIG_SYS_FSL_ESDHC_ADDR      CONFIG_SYS_MPC85xx_ESDHC_ADDR
-#define CONFIG_CMD_MMC
 #define CONFIG_GENERIC_MMC
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
 #define CONFIG_DOS_PARTITION
 #endif
 
@@ -849,15 +809,9 @@ unsigned long get_board_ddr_clk(void);
  * Command line configuration.
  */
 #define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
 #define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
 #define CONFIG_CMD_ERRATA
-#define CONFIG_CMD_GREPENV
 #define CONFIG_CMD_IRQ
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
 #define CONFIG_CMD_REGINFO
 
 #ifdef CONFIG_PCI
@@ -871,7 +825,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_CMDLINE_EDITING                 /* Command-line editing */
 #define CONFIG_AUTO_COMPLETE                   /* add autocompletion support */
 #define CONFIG_SYS_LOAD_ADDR   0x2000000       /* default load address */
-#define CONFIG_SYS_PROMPT      "=> "           /* Monitor Command Prompt */
 #ifdef CONFIG_CMD_KGDB
 #define CONFIG_SYS_CBSIZE      1024            /* Console I/O Buffer Size */
 #else
@@ -900,11 +853,9 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_BOOTFILE                "uImage"
 #define CONFIG_UBOOTPATH       "u-boot.bin" /* U-Boot image on TFTP server */
 #define CONFIG_LOADADDR                1000000 /* default location for tftp, bootm */
-#define CONFIG_BOOTDELAY       10      /* -1 disables auto-boot */
 #define CONFIG_BAUDRATE                115200
 #define __USB_PHY_TYPE         utmi
 
-
 #define        CONFIG_EXTRA_ENV_SETTINGS                               \
        "hwconfig=fsl_ddr:ctlr_intlv=cacheline,bank_intlv=cs0_cs1;\0"  \
        "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0" \
@@ -945,8 +896,12 @@ unsigned long get_board_ddr_clk(void);
 
 #define CONFIG_BOOTCOMMAND     CONFIG_LINUX
 
-#ifdef CONFIG_SECURE_BOOT
-#include <asm/fsl_secure_boot.h>
+/* Hash command with SHA acceleration supported in hardware */
+#ifdef CONFIG_FSL_CAAM
+#define CONFIG_CMD_HASH
+#define CONFIG_SHA_HW_ACCEL
 #endif
 
+#include <asm/fsl_secure_boot.h>
+
 #endif /* __T1024QDS_H */