Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig

[people/ms/u-boot.git] / include / configs / T208xQDS.h

diff --git a/include/configs/T208xQDS.h b/include/configs/T208xQDS.h
index af0dada7ea3fcf684721c3788b748b0aa4a9293c..50413eb24763e6da6b8c72fb733818de3e808635 100644 (file)
--- a/include/configs/T208xQDS.h
+++ b/include/configs/T208xQDS.h
@@ -39,7 +39,6 @@
 
 #define CONFIG_SPL_FLUSH_IMAGE
 #define CONFIG_SPL_TARGET              "u-boot-with-spl.bin"
-#define CONFIG_SYS_TEXT_BASE           0x00201000
 #define CONFIG_SPL_TEXT_BASE           0xFFFD8000
 #define CONFIG_SPL_PAD_TO              0x40000
 #define CONFIG_SPL_MAX_SIZE            0x28000
@@ -86,7 +85,6 @@
 
 #ifdef CONFIG_SDCARD
 #define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
-#define CONFIG_SPL_MMC_MINIMAL
 #define CONFIG_SYS_MMC_U_BOOT_SIZE     (768 << 10)
 #define CONFIG_SYS_MMC_U_BOOT_DST      (0x00200000)
 #define CONFIG_SYS_MMC_U_BOOT_START    (0x00200000)
@@ -114,10 +112,6 @@
 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
 #endif
 
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE   0xeff40000
-#endif
-
 #ifndef CONFIG_RESET_VECTOR_ADDRESS
 #define CONFIG_RESET_VECTOR_ADDRESS    0xeffffffc
 #endif
@@ -141,7 +135,6 @@
 
 #if defined(CONFIG_SPIFLASH)
 #define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_SPI_FLASH
 #define CONFIG_ENV_SPI_BUS     0
 #define CONFIG_ENV_SPI_CS      0
 #define CONFIG_ENV_SPI_MAX_HZ  10000000
@@ -151,23 +144,19 @@
 #define CONFIG_ENV_SECT_SIZE   0x10000
 #elif defined(CONFIG_SDCARD)
 #define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_MMC
 #define CONFIG_SYS_MMC_ENV_DEV 0
 #define CONFIG_ENV_SIZE                0x2000
 #define CONFIG_ENV_OFFSET      (512 * 0x800)
 #elif defined(CONFIG_NAND)
 #define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_NAND
 #define CONFIG_ENV_SIZE                0x2000
 #define CONFIG_ENV_OFFSET      (10 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
-#define CONFIG_ENV_IS_IN_REMOTE
 #define CONFIG_ENV_ADDR                0xffe20000
 #define CONFIG_ENV_SIZE                0x2000
 #elif defined(CONFIG_ENV_IS_NOWHERE)
 #define CONFIG_ENV_SIZE                0x2000
 #else
-#define CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_ENV_ADDR                (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
 #define CONFIG_ENV_SIZE                0x2000
 #define CONFIG_ENV_SECT_SIZE   0x20000 /* 128K (one sector) */
@@ -342,7 +331,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_NAND_DDR_LAW                11
 #define CONFIG_SYS_NAND_BASE_LIST      { CONFIG_SYS_NAND_BASE }
 #define CONFIG_SYS_MAX_NAND_DEVICE     1
-#define CONFIG_CMD_NAND
 #define CONFIG_SYS_NAND_BLOCK_SIZE     (128 * 1024)
 
 #if defined(CONFIG_NAND)
@@ -540,7 +528,7 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_PCIE2           /* PCIE controller 2 */
 #define CONFIG_PCIE3           /* PCIE controller 3 */
 #define CONFIG_PCIE4           /* PCIE controller 4 */
-#define CONFIG_FSL_PCIE_RESET
+#define CONFIG_FSL_PCIE_RESET   /* pcie reset fix link width 2x-4x*/
 #define CONFIG_FSL_PCI_INIT    /* Use common FSL init code */
 #define CONFIG_SYS_PCI_64BIT   /* enable 64-bit PCI resources */
 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
@@ -584,13 +572,11 @@ unsigned long get_board_ddr_clk(void);
 
 #ifdef CONFIG_PCI
 #define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_FSL_PCIE_RESET     /* need PCIe reset errata */
 #define CONFIG_PCI_SCAN_SHOW   /* show pci devices on startup */
 #endif
 
 /* Qman/Bman */
 #ifndef CONFIG_NOBQFMAN
-#define CONFIG_SYS_DPAA_QBMAN          /* Support Q/Bman */
 #define CONFIG_SYS_BMAN_NUM_PORTALS    18
 #define CONFIG_SYS_BMAN_MEM_BASE       0xf4000000
 #define CONFIG_SYS_BMAN_MEM_PHYS       0xff4000000ull
@@ -678,15 +664,12 @@ unsigned long get_board_ddr_clk(void);
 #ifdef CONFIG_FMAN_ENET
 #define CONFIG_MII             /* MII PHY management */
 #define CONFIG_ETHPRIME                "FM1@DTSEC3"
-#define CONFIG_PHY_GIGE                /* Include GbE speed/duplex detection */
 #endif
 
 /*
  * SATA
  */
 #ifdef CONFIG_FSL_SATA_V2
-#define CONFIG_LIBATA
-#define CONFIG_FSL_SATA
 #define CONFIG_SYS_SATA_MAX_DEVICE     2
 #define CONFIG_SATA1
 #define CONFIG_SYS_SATA1               CONFIG_SYS_MPC85xx_SATA1_ADDR
@@ -695,7 +678,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_SATA2               CONFIG_SYS_MPC85xx_SATA2_ADDR
 #define CONFIG_SYS_SATA2_FLAGS         FLAGS_DMA
 #define CONFIG_LBA48
-#define CONFIG_CMD_SATA
 #endif
 
 /*
@@ -725,14 +707,7 @@ unsigned long get_board_ddr_clk(void);
 #ifdef CONFIG_MTD_NOR_FLASH
 #define CONFIG_MTD_DEVICE
 #define CONFIG_MTD_PARTITIONS
-#define CONFIG_CMD_MTDPARTS
 #define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT "nor0=fe8000000.nor,nand0=fff800000.flash," \
-                       "spi0=spife110000.0"
-#define MTDPARTS_DEFAULT "mtdparts=fe8000000.nor:1m(uboot),5m(kernel)," \
-                       "128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot)," \
-                       "5m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:" \
-                       "1m(uboot),5m(kernel),128k(dtb),-(user)"
 #endif
 
 /*
@@ -741,31 +716,10 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_LOADS_ECHO      /* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE   /* allow baudrate change */
 
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_REGINFO
-
-#ifdef CONFIG_PCI
-#define CONFIG_CMD_PCI
-#endif
-
 /*
  * Miscellaneous configurable options
  */
-#define CONFIG_SYS_LONGHELP            /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING         /* Command-line editing */
-#define CONFIG_AUTO_COMPLETE           /* add autocompletion support */
 #define CONFIG_SYS_LOAD_ADDR   0x2000000 /* default load address */
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_SYS_CBSIZE      1024      /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE      256       /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS     16      /* max number of command args */
-#define CONFIG_SYS_BARGSIZE    CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
 
 /*
  * For booting Linux, the board info and command line data