spi: Move SPI drivers to defconfig

[people/ms/u-boot.git] / include / configs / T208xQDS.h

diff --git a/include/configs/T208xQDS.h b/include/configs/T208xQDS.h
index 8dd2e492ba8ef95d5fb9d9a9679c5a3afb0ecd0d..c0c8c09decde75f145b9ef8b9604d751f19bc9b3 100644 (file)
--- a/include/configs/T208xQDS.h
+++ b/include/configs/T208xQDS.h
@@ -11,9 +11,9 @@
 #ifndef __T208xQDS_H
 #define __T208xQDS_H
 
+#define CONFIG_DISPLAY_BOARDINFO
 #define CONFIG_ICS307_REFCLK_HZ 25000000  /* ICS307 ref clk freq */
 #define CONFIG_MMC
-#define CONFIG_SPI_FLASH
 #define CONFIG_USB_EHCI
 #if defined(CONFIG_PPC_T2080)
 #define CONFIG_T2080QDS
@@ -42,6 +42,7 @@
 #define CONFIG_SYS_FSL_CPC     /* Corenet Platform Cache */
 #define CONFIG_SYS_NUM_CPC     CONFIG_NUM_DDR_CONTROLLERS
 #define CONFIG_FSL_IFC         /* Enable IFC Support */
+#define CONFIG_FSL_CAAM                /* Enable SEC/CAAM */
 #define CONFIG_FSL_LAW         /* Use common FSL init code */
 #define CONFIG_ENV_OVERWRITE
 
@@ -53,7 +54,6 @@
 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xqds/t2081_rcw.cfg
 #endif
 
-#define CONFIG_SPL
 #define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
 #define CONFIG_SPL_ENV_SUPPORT
 #define CONFIG_SPL_SERIAL_SUPPORT
@@ -227,11 +227,12 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_VERY_BIG_RAM
 #define CONFIG_SYS_DDR_SDRAM_BASE      0x00000000
 #define CONFIG_SYS_SDRAM_BASE          CONFIG_SYS_DDR_SDRAM_BASE
-#define CONFIG_DIMM_SLOTS_PER_CTLR     1
-#define CONFIG_CHIP_SELECTS_PER_CTRL   (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
+#define CONFIG_DIMM_SLOTS_PER_CTLR     2
+#define CONFIG_CHIP_SELECTS_PER_CTRL   (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
+#define CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE
 #define CONFIG_DDR_SPD
 #define CONFIG_SYS_FSL_DDR3
-#undef CONFIG_FSL_DDR_INTERACTIVE
+#define CONFIG_FSL_DDR_INTERACTIVE
 #define CONFIG_SYS_SPD_BUS_NUM 0
 #define CONFIG_SYS_SDRAM_SIZE  2048    /* for fixed parameter use */
 #define SPD_EEPROM_ADDRESS1    0x51
@@ -354,7 +355,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_NAND_DDR_LAW                11
 #define CONFIG_SYS_NAND_BASE_LIST      { CONFIG_SYS_NAND_BASE }
 #define CONFIG_SYS_MAX_NAND_DEVICE     1
-#define CONFIG_MTD_NAND_VERIFY_WRITE
 #define CONFIG_CMD_NAND
 #define CONFIG_SYS_NAND_BLOCK_SIZE     (128 * 1024)
 
@@ -429,7 +429,7 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_INIT_RAM_LOCK
 #define CONFIG_SYS_INIT_RAM_ADDR       0xfdd00000 /* Initial L1 address */
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH     0xf
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW      0xfe0ec000
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW      0xfe03c000
 /* The assembler doesn't like typecast */
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
                        ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
@@ -445,7 +445,6 @@ unsigned long get_board_ddr_clk(void);
  * Serial Port
  */
 #define CONFIG_CONS_INDEX              1
-#define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
 #define CONFIG_SYS_NS16550_CLK         (get_bus_freq(0)/2)
@@ -491,6 +490,23 @@ unsigned long get_board_ddr_clk(void);
 #define I2C_MUX_PCA_ADDR_SEC2  0x76 /* I2C bus multiplexer,secondary 2 */
 #define I2C_MUX_CH_DEFAULT     0x8
 
+#define I2C_MUX_CH_VOL_MONITOR 0xa
+
+/* Voltage monitor on channel 2*/
+#define I2C_VOL_MONITOR_ADDR           0x40
+#define I2C_VOL_MONITOR_BUS_V_OFFSET   0x2
+#define I2C_VOL_MONITOR_BUS_V_OVF      0x1
+#define I2C_VOL_MONITOR_BUS_V_SHIFT    3
+
+#define CONFIG_VID_FLS_ENV             "t208xqds_vdd_mv"
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_VID
+#endif
+#define CONFIG_VOL_MONITOR_IR36021_SET
+#define CONFIG_VOL_MONITOR_IR36021_READ
+/* The lowest and highest voltage allowed for T208xQDS */
+#define VDD_MV_MIN                     819
+#define VDD_MV_MAX                     1212
 
 /*
  * RapidIO
@@ -534,9 +550,8 @@ unsigned long get_board_ddr_clk(void);
  * eSPI - Enhanced SPI
  */
 #ifdef CONFIG_SPI_FLASH
-#define CONFIG_FSL_ESPI
 #define CONFIG_SPI_FLASH_STMICRO
-#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_RAMBOOT_PBL)
+#ifndef CONFIG_SPL_BUILD
 #define CONFIG_SPI_FLASH_SST
 #define CONFIG_SPI_FLASH_EON
 #endif
@@ -556,6 +571,7 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_PCIE2           /* PCIE controler 2 */
 #define CONFIG_PCIE3           /* PCIE controler 3 */
 #define CONFIG_PCIE4           /* PCIE controler 4 */
+#define CONFIG_FSL_PCIE_RESET
 #define CONFIG_FSL_PCI_INIT    /* Use common FSL init code */
 #define CONFIG_SYS_PCI_64BIT   /* enable 64-bit PCI resources */
 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
@@ -600,8 +616,6 @@ unsigned long get_board_ddr_clk(void);
 #ifdef CONFIG_PCI
 #define CONFIG_PCI_INDIRECT_BRIDGE
 #define CONFIG_FSL_PCIE_RESET     /* need PCIe reset errata */
-#define CONFIG_NET_MULTI
-#define CONFIG_E1000
 #define CONFIG_PCI_PNP         /* do pci plug-and-play */
 #define CONFIG_PCI_SCAN_SHOW   /* show pci devices on startup */
 #define CONFIG_DOS_PARTITION
@@ -614,10 +628,26 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_BMAN_MEM_BASE       0xf4000000
 #define CONFIG_SYS_BMAN_MEM_PHYS       0xff4000000ull
 #define CONFIG_SYS_BMAN_MEM_SIZE       0x02000000
+#define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
+#define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
+#define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
+#define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
+#define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
+                                       CONFIG_SYS_BMAN_CENA_SIZE)
+#define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
+#define CONFIG_SYS_BMAN_SWP_ISDR_REG    0xE08
 #define CONFIG_SYS_QMAN_NUM_PORTALS    18
 #define CONFIG_SYS_QMAN_MEM_BASE       0xf6000000
 #define CONFIG_SYS_QMAN_MEM_PHYS       0xff6000000ull
 #define CONFIG_SYS_QMAN_MEM_SIZE       0x02000000
+#define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
+#define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
+#define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
+#define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
+#define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
+                                       CONFIG_SYS_QMAN_CENA_SIZE)
+#define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
+#define CONFIG_SYS_QMAN_SWP_ISDR_REG   0xE08
 
 #define CONFIG_SYS_DPAA_FMAN
 #define CONFIG_SYS_DPAA_PME
@@ -721,6 +751,7 @@ unsigned long get_board_ddr_clk(void);
 #ifdef CONFIG_MMC
 #define CONFIG_CMD_MMC
 #define CONFIG_FSL_ESDHC
+#define define CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK
 #define CONFIG_SYS_FSL_ESDHC_ADDR      CONFIG_SYS_MPC85xx_ESDHC_ADDR
 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
@@ -728,6 +759,7 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_CMD_EXT2
 #define CONFIG_CMD_FAT
 #define CONFIG_DOS_PARTITION
+#define CONFIG_FSL_ESDHC_ADAPTER_IDENT
 #endif
 
 
@@ -756,23 +788,23 @@ unsigned long get_board_ddr_clk(void);
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
 #define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
 #define CONFIG_CMD_ERRATA
 #define CONFIG_CMD_GREPENV
 #define CONFIG_CMD_IRQ
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_PING
-#define CONFIG_CMD_SETEXPR
 #define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_BDI
 
 #ifdef CONFIG_PCI
 #define CONFIG_CMD_PCI
-#define CONFIG_CMD_NET
+#endif
+
+/* Hash command with SHA acceleration supported in hardware */
+#ifdef CONFIG_FSL_CAAM
+#define CONFIG_CMD_HASH
+#define CONFIG_SHA_HW_ACCEL
 #endif
 
 /*
@@ -782,7 +814,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_CMDLINE_EDITING         /* Command-line editing */
 #define CONFIG_AUTO_COMPLETE           /* add autocompletion support */
 #define CONFIG_SYS_LOAD_ADDR   0x2000000 /* default load address */
-#define CONFIG_SYS_PROMPT      "=> "     /* Monitor Command Prompt */
 #ifdef CONFIG_CMD_KGDB
 #define CONFIG_SYS_CBSIZE      1024      /* Console I/O Buffer Size */
 #else
@@ -907,6 +938,7 @@ unsigned long get_board_ddr_clk(void);
 
 #ifdef CONFIG_SECURE_BOOT
 #include <asm/fsl_secure_boot.h>
+#define CONFIG_CMD_BLOB
 #undef CONFIG_CMD_USB
 #endif