Move CONFIG_OF_LIBFDT to Kconfig

[people/ms/u-boot.git] / include / configs / T208xRDB.h

diff --git a/include/configs/T208xRDB.h b/include/configs/T208xRDB.h
index db6b42ea0f1cf3681fe2fda1f16268a53f4a9ee3..43ff63e7ad6fa00496b161dc35d38083aa18d9b6 100644 (file)
--- a/include/configs/T208xRDB.h
+++ b/include/configs/T208xRDB.h
@@ -11,12 +11,10 @@
 #ifndef __T2080RDB_H
 #define __T2080RDB_H
 
-#define CONFIG_SYS_GENERIC_BOARD
 #define CONFIG_DISPLAY_BOARDINFO
 #define CONFIG_T2080RDB
 #define CONFIG_ICS307_REFCLK_HZ 25000000  /* ICS307 ref clk freq */
 #define CONFIG_MMC
-#define CONFIG_SPI_FLASH
 #define CONFIG_USB_EHCI
 #define CONFIG_FSL_SATA_V2
 
@@ -140,6 +138,11 @@
 #define CONFIG_MEM_INIT_VALUE          0xdeadbeef
 #endif
 
+#define CONFIG_CMD_MEMTEST
+#define CONFIG_SYS_MEMTEST_START       0x00200000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END         0x00400000
+#define CONFIG_SYS_ALT_MEMTEST
+
 #ifndef CONFIG_SYS_NO_FLASH
 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_SYS_FLASH_CFI
@@ -328,7 +331,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_NAND_DDR_LAW                11
 #define CONFIG_SYS_NAND_BASE_LIST      { CONFIG_SYS_NAND_BASE }
 #define CONFIG_SYS_MAX_NAND_DEVICE     1
-#define CONFIG_MTD_NAND_VERIFY_WRITE
 #define CONFIG_CMD_NAND
 #define CONFIG_SYS_NAND_BLOCK_SIZE     (512 * 1024)
 
@@ -387,7 +389,7 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_INIT_RAM_LOCK
 #define CONFIG_SYS_INIT_RAM_ADDR       0xfdd00000 /* Initial L1 address */
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH     0xf
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW      0xfe0ec000
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW      0xfe03c000
 /* The assembler doesn't like typecast */
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
                        ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
@@ -403,7 +405,6 @@ unsigned long get_board_ddr_clk(void);
  * Serial Port
  */
 #define CONFIG_CONS_INDEX              1
-#define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
 #define CONFIG_SYS_NS16550_CLK         (get_bus_freq(0)/2)
@@ -419,7 +420,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
 
 /* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT
 #define CONFIG_OF_BOARD_SETUP
 #define CONFIG_OF_STDOUT_VIA_ALIAS
 
@@ -449,6 +449,17 @@ unsigned long get_board_ddr_clk(void);
 #define I2C_MUX_PCA_ADDR_SEC2  0x76 /* I2C bus multiplexer,secondary 2 */
 #define I2C_MUX_CH_DEFAULT     0x8
 
+#define I2C_MUX_CH_VOL_MONITOR 0xa
+
+#define CONFIG_VID_FLS_ENV             "t208xrdb_vdd_mv"
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_VID
+#endif
+#define CONFIG_VOL_MONITOR_IR36021_SET
+#define CONFIG_VOL_MONITOR_IR36021_READ
+/* The lowest and highest voltage allowed for T208xRDB */
+#define VDD_MV_MIN                     819
+#define VDD_MV_MAX                     1212
 
 /*
  * RapidIO
@@ -492,8 +503,6 @@ unsigned long get_board_ddr_clk(void);
  * eSPI - Enhanced SPI
  */
 #ifdef CONFIG_SPI_FLASH
-#define CONFIG_FSL_ESPI
-#define CONFIG_SPI_FLASH_STMICRO
 #define CONFIG_SPI_FLASH_BAR
 #define CONFIG_CMD_SF
 #define CONFIG_SF_DEFAULT_SPEED         10000000
@@ -553,8 +562,6 @@ unsigned long get_board_ddr_clk(void);
 #ifdef CONFIG_PCI
 #define CONFIG_PCI_INDIRECT_BRIDGE
 #define CONFIG_FSL_PCIE_RESET           /* need PCIe reset errata LSZ ADD */
-#define CONFIG_NET_MULTI
-#define CONFIG_E1000
 #define CONFIG_PCI_PNP         /* do pci plug-and-play */
 #define CONFIG_PCI_SCAN_SHOW   /* show pci devices on startup */
 #define CONFIG_DOS_PARTITION
@@ -647,8 +654,8 @@ unsigned long get_board_ddr_clk(void);
 #ifdef CONFIG_SYS_DPAA_FMAN
 #define CONFIG_FMAN_ENET
 #define CONFIG_PHYLIB_10G
+#define CONFIG_PHY_AQUANTIA
 #define CONFIG_PHY_CORTINA
-#define CONFIG_PHY_AQ1202
 #define CONFIG_PHY_REALTEK
 #define CONFIG_CORTINA_FW_LENGTH       0x40000
 #define RGMII_PHY1_ADDR                0x01  /* RealTek RTL8211E */
@@ -735,22 +742,15 @@ unsigned long get_board_ddr_clk(void);
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
 #define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
 #define CONFIG_CMD_ERRATA
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_PING
-#define CONFIG_CMD_ECHO
-#define CONFIG_CMD_SETEXPR
 #define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_BDI
 
 #ifdef CONFIG_PCI
 #define CONFIG_CMD_PCI
-#define CONFIG_CMD_NET
 #endif
 
 /* Hash command with SHA acceleration supported in hardware */
@@ -888,10 +888,6 @@ unsigned long get_board_ddr_clk(void);
 
 #define CONFIG_BOOTCOMMAND             CONFIG_LINUX
 
-#ifdef CONFIG_SECURE_BOOT
 #include <asm/fsl_secure_boot.h>
-#define CONFIG_CMD_BLOB
-#undef CONFIG_CMD_USB
-#endif
 
 #endif /* __T2080RDB_H */