/*
- * (C) Copyright 2003-2005
+ * (C) Copyright 2003-2014
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* (C) Copyright 2004-2006
* Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de
*
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
* (easy to change)
*/
-#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */
-#define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */
+#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */
#define CONFIG_TQM5200 1 /* ... on TQM5200 module */
#undef CONFIG_TQM5200_REV100 /* define for revision 100 modules */
+#define CONFIG_DISPLAY_BOARDINFO
/*
* Valid values for CONFIG_SYS_TEXT_BASE are:
#endif
/* On a Cameron or on a FO300 board or ... */
-#if !defined(CONFIG_CAM5200) && !defined(CONFIG_FO300)
+#if !defined(CONFIG_CAM5200) && !defined(CONFIG_CHARON) \
+ && !defined(CONFIG_FO300)
#define CONFIG_STK52XX 1 /* ... on a STK52XX board */
#endif
#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
#define CONFIG_HIGH_BATS 1 /* High BATs supported */
/*
/* switch is open */
#endif /* CONFIG_FO300 */
-#ifdef CONFIG_STK52XX
+#if defined(CONFIG_CHARON) || defined(CONFIG_STK52XX)
#define CONFIG_PS2KBD /* AT-PS/2 Keyboard */
#define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */
#define CONFIG_PS2SERIAL 6 /* .. on PSC6 */
* 0x40000000 - 0x4fffffff - PCI Memory
* 0x50000000 - 0x50ffffff - PCI IO Space
*/
-#ifdef CONFIG_STK52XX
+#if defined(CONFIG_CHARON) || defined(CONFIG_STK52XX)
#define CONFIG_PCI 1
#define CONFIG_PCI_PNP 1
/* #define CONFIG_PCI_SCAN_SHOW 1 */
#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
#define CONFIG_PCI_IO_SIZE 0x01000000
-#define CONFIG_NET_MULTI 1
#define CONFIG_EEPRO100 1
#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define CONFIG_NS8382X 1
#define CONFIG_ISO_PARTITION
/* USB */
-#if defined(CONFIG_STK52XX) || defined(CONFIG_FO300)
+#if defined(CONFIG_CHARON) || defined(CONFIG_FO300) || \
+ defined(CONFIG_STK52XX)
#define CONFIG_USB_OHCI_NEW
#define CONFIG_SYS_OHCI_BE_CONTROLLER
#define CONFIG_USB_STORAGE
/*
* Command line configuration.
*/
-#include <config_cmd_default.h>
-
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DATE
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_I2C
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_MII
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PING
#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SNTP
#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
#endif
-#if defined(CONFIG_MINIFAP) || defined(CONFIG_STK52XX) || defined(CONFIG_FO300)
+#if defined(CONFIG_CHARON) || defined(CONFIG_FO300) || \
+ defined(CONFIG_MINIFAP) || defined(CONFIG_STK52XX)
#define CONFIG_CMD_IDE
#define CONFIG_CMD_FAT
#define CONFIG_CMD_EXT2
#endif
-#if defined(CONFIG_STK52XX) || defined(CONFIG_FO300)
+#if defined(CONFIG_CHARON) || defined(CONFIG_FO300) || \
+ defined(CONFIG_STK52XX)
#define CONFIG_CFG_USB
#define CONFIG_CFG_FAT
#endif
"fdt_addr=FC100000\0" \
"kernel_addr=FC140000\0" \
"ramdisk_addr=FC600000\0"
+#elif defined(CONFIG_CHARON)
+#define ENV_FLASH_LAYOUT \
+ "fdt_addr=FDFC0000\0" \
+ "kernel_addr=FC0A0000\0" \
+ "ramdisk_addr=FC200000\0"
#else /* !CONFIG_TQM5200_B */
#define ENV_FLASH_LAYOUT \
"fdt_addr=FC0A0000\0" \
":${hostname}:${netdev}:off panic=1\0" \
"addcons=setenv bootargs ${bootargs} " \
"console=${console},${baudrate}\0" \
- "flash_self_old=sete console ttyS0; run ramargs addip addcons;" \
+ "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
+ "flash_self_old=sete console ttyS0; " \
+ "run ramargs addip addcons addmtd; " \
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
"flash_self=run ramargs addip addcons;" \
"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
"sete console ttyS0; run nfsargs addip addcons;bootm\0" \
"net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
"tftp ${fdt_addr_r} ${fdt_file}; " \
- "run nfsargs addip addcons; " \
+ "run nfsargs addip addcons addmtd; " \
"bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
CUSTOM_ENV_SETTINGS \
"load=tftp 200000 ${u-boot}\0" \
*
* Please notice, that the resulting clock frequency could differ from the
* configured value. This is because the I2C clock is derived from system
- * clock over a frequency divider with only a few divider values. U-boot
+ * clock over a frequency divider with only a few divider values. U-Boot
* calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated
* approximation allways lies below the configured value, never above.
*/
/* List of I2C addresses to be verified by POST */
#if defined (CONFIG_MINIFAP)
-#undef I2C_ADDR_LIST
-#define I2C_ADDR_LIST { CONFIG_SYS_I2C_EEPROM_ADDR, \
- CONFIG_SYS_I2C_HWMON_ADDR, \
- CONFIG_SYS_I2C_SLAVE }
+#undef CONFIG_SYS_POST_I2C_ADDRS
+#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_EEPROM_ADDR, \
+ CONFIG_SYS_I2C_HWMON_ADDR, \
+ CONFIG_SYS_I2C_SLAVE}
#endif
/*
/* use CFI flash driver */
#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
+#define CONFIG_FLASH_CFI_MTD /* with MTD support */
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_BOOTCS_START }
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks
(= chip selects) */
/* Dynamic MTD partition support */
#define CONFIG_CMD_MTDPARTS
#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
-#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT "nor0=TQM5200-0"
+#define MTDIDS_DEFAULT "nor0=fc000000.flash"
-#ifdef CONFIG_STK52XX
+#if defined(CONFIG_STK52XX)
# if defined(CONFIG_TQM5200_B)
# if defined(CONFIG_SYS_LOWBOOT)
-# define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:1m(firmware)," \
+# define MTDPARTS_DEFAULT "mtdparts=fc000000.flash:1m(firmware)," \
"256k(dtb)," \
"2304k(kernel)," \
"2560k(small-fs)," \
"8m(misc)," \
"16m(big-fs)"
# else /* highboot */
-# define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:2560k(kernel)," \
+# define MTDPARTS_DEFAULT "mtdparts=fc000000.flash:2560k(kernel),"\
"3584k(small-fs)," \
"2m(initrd)," \
"8m(misc)," \
"1m(firmware)"
# endif /* CONFIG_SYS_LOWBOOT */
# else /* !CONFIG_TQM5200_B */
-# define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:640k(firmware)," \
+# define MTDPARTS_DEFAULT "mtdparts=fc000000.flash:640k(firmware),"\
"128k(dtb)," \
"2304k(kernel)," \
"2m(initrd)," \
"15m(big-fs)"
# endif /* CONFIG_TQM5200_B */
#elif defined (CONFIG_CAM5200)
-# define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:768k(firmware)," \
+# define MTDPARTS_DEFAULT "mtdparts=fc000000.flash:768k(firmware),"\
"1792k(kernel)," \
"5632k(rootfs)," \
"24m(home)"
+#elif defined (CONFIG_CHARON)
+# define MTDPARTS_DEFAULT "mtdparts=fc000000.flash:640k(firmware),"\
+ "1408k(kernel)," \
+ "2m(initrd)," \
+ "4m(small-fs)," \
+ "24320k(big-fs)," \
+ "256k(dts)"
#elif defined (CONFIG_FO300)
-# define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:640k(firmware)," \
+# define MTDPARTS_DEFAULT "mtdparts=fc000000.flash:640k(firmware),"\
"1408k(kernel)," \
"2m(initrd)," \
"4m(small-fs)," \
#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
#ifdef CONFIG_POST
/* preserve space for the post_word at end of on-chip SRAM */
-#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_POST_SIZE
+#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE
#else
-#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_SIZE
+#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE
#endif
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
* use PSC1: Bits 29-31 (mask: 0x00000007):
* 100 -> UART (on all boards).
*/
+#if !defined(CONFIG_SYS_GPS_PORT_CONFIG)
#if defined (CONFIG_MINIFAP)
# define CONFIG_SYS_GPS_PORT_CONFIG 0x91000004
#elif defined (CONFIG_STK52XX)
#else /* TMQ5200 Inbetriebnahme-Board */
# define CONFIG_SYS_GPS_PORT_CONFIG 0x81000004
#endif
+#endif
/*
* RTC configuration
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_SYS_HUSH_PARSER 1 /* use "hush" command parser */
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-
/*
* Enable loopw command.
*/
* Open firmware flat tree support
*-----------------------------------------------------------------------
*/
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#define OF_CPU "PowerPC,5200@0"
#define OF_SOC "soc5200@f0000000"
#define OF_TBCLK (bd->bi_busfreq / 4)
projects / people / ms / u-boot.git / blobdiff