configs: Migrate RBTREE, LZO, CMD_MTDPARTS, CMD_UBI and CMD_UBIFS

[people/ms/u-boot.git] / include / configs / TQM834x.h

diff --git a/include/configs/TQM834x.h b/include/configs/TQM834x.h
index 6762e3a57e2c71587ac4b2ded949cdfe06d25fab..c54de6507633d53a43ee3c1047b26fde87b4b823 100644 (file)
--- a/include/configs/TQM834x.h
+++ b/include/configs/TQM834x.h
@@ -41,7 +41,6 @@
 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_8
 
 /* board pre init: do not call, nothing to do */
-#undef CONFIG_BOARD_EARLY_INIT_F
 
 /* detect the number of flash banks */
 #define CONFIG_BOARD_EARLY_INIT_R
@@ -156,7 +155,6 @@
  * Serial Port
  */
 #define CONFIG_CONS_INDEX      1
-#define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
 #define CONFIG_SYS_NS16550_CLK         get_bus_freq(0)
@@ -181,19 +179,11 @@
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN         2       /* 16 bit */
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS      5       /* 32 bytes/write */
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS  12      /* 10ms +/- 20% */
-#define CONFIG_SYS_I2C_MULTI_EEPROMS           /* more than one eeprom */
 
 /* I2C RTC */
 #define CONFIG_RTC_DS1337                      /* use ds1337 rtc via i2c */
 #define CONFIG_SYS_I2C_RTC_ADDR                0x68    /* at address 0x68 */
 
-/* I2C SYSMON (LM75) */
-#define CONFIG_DTT_LM75                        1       /* ON Semi's LM75 */
-#define CONFIG_DTT_SENSORS             {0}     /* Sensor addresses */
-#define CONFIG_SYS_DTT_MAX_TEMP                70
-#define CONFIG_SYS_DTT_LOW_TEMP                -30
-#define CONFIG_SYS_DTT_HYSTERESIS      3
-
 /*
  * TSEC
  */
@@ -227,11 +217,9 @@
  * General PCI
  * Addresses are mapped 1-1.
  */
-#define CONFIG_PCI
 
 #if defined(CONFIG_PCI)
 
-#define CONFIG_PCI_PNP                 /* do pci plug-and-play */
 #define CONFIG_PCI_SCAN_SHOW           /* show pci devices on startup */
 
 /* PCI1 host bridge */
@@ -282,34 +270,13 @@
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 
-
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DTT
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_SNTP
-
 #if defined(CONFIG_PCI)
     #define CONFIG_CMD_PCI
 #endif
 
-#if defined(CONFIG_SYS_RAMBOOT)
-    #undef CONFIG_CMD_SAVEENV
-    #undef CONFIG_CMD_LOADS
-#endif
-
 /*
  * Miscellaneous configurable options
  */
@@ -319,8 +286,6 @@
 #define CONFIG_CMDLINE_EDITING 1       /* add command line history */
 #define CONFIG_AUTO_COMPLETE           /* add autocompletion support */
 
-#define CONFIG_SYS_HUSH_PARSER         1       /* Use the HUSH parser */
-
 #if defined(CONFIG_CMD_KGDB)
        #define CONFIG_SYS_CBSIZE       1024    /* Console I/O Buffer Size */
 #else
@@ -335,11 +300,6 @@
 
 #undef CONFIG_WATCHDOG         /* watchdog disabled */
 
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT       1
-#define CONFIG_OF_BOARD_SETUP  1
-#define CONFIG_OF_STDOUT_VIA_ALIAS     1
-
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 256 MB of memory, since this is
@@ -503,11 +463,8 @@
                                /* default location for tftp and bootm */
 #define CONFIG_LOADADDR                400000
 
-#define CONFIG_BOOTDELAY       6       /* -1 disables auto-boot */
 #undef  CONFIG_BOOTARGS                /* the boot command will set bootargs */
 
-#define CONFIG_BAUDRATE                115200
-
 #define CONFIG_PREBOOT "echo;" \
        "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
        "echo"
@@ -561,7 +518,6 @@
  * JFFS2 partitions
  */
 /* mtdparts command line support */
-#define CONFIG_CMD_MTDPARTS
 #define CONFIG_MTD_DEVICE              /* needed for mtdparts commands */
 #define CONFIG_FLASH_CFI_MTD
 #define MTDIDS_DEFAULT         "nor0=TQM834x-0"