configs: Re-sync HUSH options

[people/ms/u-boot.git] / include / configs / TQM866M.h

diff --git a/include/configs/TQM866M.h b/include/configs/TQM866M.h
index f28aa16c02b39d210f8ac50143a567e5b57ed6ac..6b585f9c4ef8d7b7a72aecd563eefb1e1216f1e9 100644 (file)
--- a/include/configs/TQM866M.h
+++ b/include/configs/TQM866M.h
@@ -1,8 +1,8 @@
 /*
- * (C) Copyright 2000-2008
+ * (C) Copyright 2000-2014
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
- * SPDX-License-Identifier:    GPL-2.0+ 
+ * SPDX-License-Identifier:    GPL-2.0+
  */
 
 /*
@@ -19,6 +19,7 @@
 
 #define CONFIG_MPC866          1       /* This is a MPC866 CPU         */
 #define CONFIG_TQM866M         1       /* ...on a TQM8xxM module       */
+#define CONFIG_DISPLAY_BOARDINFO
 
 #define        CONFIG_SYS_TEXT_BASE    0x40000000
 
@@ -91,13 +92,11 @@
 #undef CONFIG_CAN_DRIVER               /* CAN Driver support disabled  */
 
 /* enable I2C and select the hardware/software driver */
-#undef CONFIG_HARD_I2C                 /* I2C with hardware support    */
-#define CONFIG_SOFT_I2C                1       /* I2C bit-banged               */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT                    /* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED      93000   /* 93 kHz is supposed to work */
+#define CONFIG_SYS_I2C_SOFT_SLAVE      0xFE
 
-#define CONFIG_SYS_I2C_SPEED           93000   /* 93 kHz is supposed to work   */
-#define CONFIG_SYS_I2C_SLAVE           0xFE
-
-#ifdef CONFIG_SOFT_I2C
 /*
  * Software (bit-bang) I2C driver configuration
  */
@@ -113,7 +112,6 @@
 #define I2C_SCL(bit)   if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
                        else    immr->im_cpm.cp_pbdat &= ~PB_SCL
 #define I2C_DELAY      udelay(2)       /* 1/4 I2C clock duration */
-#endif /* CONFIG_SOFT_I2C */
 
 #define CONFIG_SYS_I2C_EEPROM_ADDR     0x50            /* EEPROM AT24C256      */
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2               /* two byte address     */
@@ -141,16 +139,12 @@
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
 #define CONFIG_CMD_EXT2
 #define CONFIG_CMD_IDE
 #define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_NFS
 #define CONFIG_CMD_SNTP
 
 
@@ -161,10 +155,8 @@
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP                    /* undef to save memory         */
-#define CONFIG_SYS_PROMPT              "=> "   /* Monitor Command Prompt       */
 
 #define CONFIG_CMDLINE_EDITING 1       /* add command line history     */
-#define CONFIG_SYS_HUSH_PARSER         1       /* Use the HUSH parser          */
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE              1024    /* Console I/O Buffer Size      */
@@ -180,8 +172,6 @@
 
 #define CONFIG_SYS_LOAD_ADDR           0x100000        /* default load address */
 
-#define CONFIG_SYS_HZ                  1000    /* decrementer freq: 1 ms ticks */
-
 /*
  * Low Level Configuration Settings
  * (address mappings, register initial values, etc.)
@@ -481,9 +471,6 @@
 #define CONFIG_FEC_ENET
 #define CONFIG_ETHPRIME                "SCC"
 
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT       1
-#define CONFIG_OF_BOARD_SETUP  1
 #define CONFIG_HWCONFIG                1
 
 #endif /* __CONFIG_H */