configs: Finish migration of PHY_GIGE

[people/ms/u-boot.git] / include / configs / UCP1020.h

diff --git a/include/configs/UCP1020.h b/include/configs/UCP1020.h
index cd46db4f6f319c48f40235c9a6fa2e5b08246a6c..56c1f2878d165969ae87a25d67d7492c4144efd8 100644 (file)
--- a/include/configs/UCP1020.h
+++ b/include/configs/UCP1020.h
@@ -118,7 +118,6 @@
 
 #define CONFIG_ENV_OVERWRITE
 
-#define CONFIG_CMD_SATA
 #define CONFIG_SATA_SIL
 #define CONFIG_SYS_SATA_MAX_DEVICE     2
 #define CONFIG_LIBATA
@@ -129,27 +128,6 @@
 
 #define CONFIG_HWCONFIG
 
-#define CONFIG_DTT_ADM1021     1       /* ADM1021 temp sensor support  */
-#define CONFIG_SYS_DTT_BUS_NUM 1       /* The I2C bus for DTT          */
-#define CONFIG_DTT_SENSORS     { 0, 1 }        /* Sensor index */
-/*
- * ADM1021/NCT72 temp sensor configuration (see dtt/adm1021.c for details).
- * there will be one entry in this array for each two (dummy) sensors in
- * CONFIG_DTT_SENSORS.
- *
- * For uCP1020 module:
- * - only one ADM1021/NCT72
- * - i2c addr 0x41
- * - conversion rate 0x02 = 0.25 conversions/second
- * - ALERT output disabled
- * - local temp sensor enabled, min set to 0 deg, max set to 85 deg
- * - remote temp sensor enabled, min set to 0 deg, max set to 85 deg
- */
-#define CONFIG_SYS_DTT_ADM1021 { { CONFIG_SYS_I2C_NCT72_ADDR, \
-                                        0x02, 0, 1, 0, 85, 1, 0, 85} }
-
-#define CONFIG_CMD_DTT
-
 /*
  * These can be toggled for performance analysis, otherwise use default.
  */
@@ -332,7 +310,7 @@
 #define CONFIG_SYS_SPD_BUS_NUM         1 /* For rom_loc and flash bank */
 
 #define CONFIG_RTC_DS1337
-#define CONFIG_SYS_RTC_DS1337_NOOSC
+#define CONFIG_RTC_DS1337_NOOSC
 #define CONFIG_SYS_I2C_RTC_ADDR                0x68
 #define CONFIG_SYS_I2C_PCA9557_ADDR    0x18
 #define CONFIG_SYS_I2C_NCT72_ADDR      0x4C
@@ -384,7 +362,6 @@
  */
 #ifdef CONFIG_ENV_FIT_UCBOOT
 
-#define CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_ENV_ADDR                (CONFIG_SYS_FLASH_BASE + 0x20000)
 #define CONFIG_ENV_SIZE                0x20000
 #define CONFIG_ENV_SECT_SIZE   0x20000 /* 128K (one sector) */
@@ -398,7 +375,6 @@
 
 #ifdef CONFIG_RAMBOOT_SPIFLASH
 
-#define CONFIG_ENV_IS_IN_SPI_FLASH
 #define CONFIG_ENV_SIZE                0x3000          /* 12KB */
 #define CONFIG_ENV_OFFSET      0x2000          /* 8KB */
 #define CONFIG_ENV_SECT_SIZE   0x1000
@@ -410,18 +386,15 @@
 #endif
 
 #elif defined(CONFIG_RAMBOOT_SDCARD)
-#define CONFIG_ENV_IS_IN_MMC
 #define CONFIG_FSL_FIXED_MMC_LOCATION
 #define CONFIG_ENV_SIZE                0x2000
 #define CONFIG_SYS_MMC_ENV_DEV 0
 
 #elif defined(CONFIG_SYS_RAMBOOT)
-#define CONFIG_ENV_IS_NOWHERE  /* Store ENV in memory only */
 #define CONFIG_ENV_ADDR                (CONFIG_SYS_MONITOR_BASE - 0x1000)
 #define CONFIG_ENV_SIZE                0x2000
 
 #else
-#define CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_ENV_BASE                (CONFIG_SYS_FLASH_BASE)
 #define CONFIG_ENV_SECT_SIZE   0x20000 /* 128K (one sector) */
 #define CONFIG_ENV_SIZE                CONFIG_ENV_SECT_SIZE
@@ -442,10 +415,7 @@
 /*
  * Command line configuration.
  */
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_IRQ
 #define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_ERRATA
 
 /*
  * USB
@@ -509,10 +479,7 @@
 
 #if defined(CONFIG_TSEC_ENET)
 
-#if defined(CONFIG_UCP1020_REV_1_2)
-#define CONFIG_PHY_MICREL_KSZ9021
-#elif defined(CONFIG_UCP1020_REV_1_3)
-#define CONFIG_PHY_MICREL_KSZ9031
+#if defined(CONFIG_UCP1020_REV_1_2) || defined(CONFIG_UCP1020_REV_1_3)
 #else
 #error "UCP1020 module revision is not defined !!!"
 #endif
@@ -537,8 +504,6 @@
 #define TSEC2_PHYIDX   0
 #define TSEC3_PHYIDX   0
 
-#define CONFIG_PHY_GIGE        1       /* Include GbE speed/duplex detection */
-
 #endif
 
 #define CONFIG_HOSTNAME                UCP1020