#define CONFIG_AM43XX
#define CONFIG_CMD_FAT
-#define CONFIG_CMD_SAVEENV
#define CONFIG_BOARD_LATE_INIT
#define CONFIG_ARCH_CPU_INIT
#define CONFIG_SYS_CACHELINE_SIZE 32
-#define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */
+#define CONFIG_MAX_RAM_BANK_SIZE (1024 << 21) /* 2GB */
#define CONFIG_SYS_TIMERBASE 0x48040000 /* Use Timer2 */
#include <asm/arch/omap.h>
/* NS16550 Configuration */
-#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_CLK 48000000
+#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_DM_SERIAL)
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE (-4)
-#define CONFIG_SYS_NS16550_CLK 48000000
+#endif
/* I2C Configuration */
#define CONFIG_CMD_EEPROM
#define CONFIG_POWER_TPS62362
/* SPL defines. */
+#ifdef CONFIG_SPL_USB_HOST_SUPPORT
+/*
+ * For USB host boot, ROM uses DMA for copying MLO from USB storage
+ * and ARM internal ram is not accessible for DMA, so SPL text base
+ * should be in OCMC ram
+ */
#define CONFIG_SPL_TEXT_BASE 0x40300350
+#else
+#define CONFIG_SPL_TEXT_BASE 0x402F4000
+#endif
#define CONFIG_SPL_MAX_SIZE (220 << 10) /* 220KB */
#define CONFIG_SYS_SPL_ARGS_ADDR (CONFIG_SYS_SDRAM_BASE + \
(128 << 20))
#endif
/* Now bring in the rest of the common code. */
-#include <configs/ti_armv7_common.h>
+#include <configs/ti_armv7_omap.h>
/* Always 64 KiB env size */
#define CONFIG_ENV_SIZE (64 << 10)
#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
/* SPL USB Support */
+#ifdef CONFIG_SPL_USB_HOST_SUPPORT
#define CONFIG_SPL_USB_SUPPORT
-#define CONFIG_SPL_USB_HOST_SUPPORT
#define CONFIG_SYS_USB_FAT_BOOT_PARTITION 1
#define CONFIG_CMD_USB
#define CONFIG_USB_HOST
#define CONFIG_USB_XHCI
+#define CONFIG_USB_XHCI_DWC3
#define CONFIG_USB_XHCI_OMAP
#define CONFIG_USB_STORAGE
#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2
#define CONFIG_OMAP_USB_PHY
#define CONFIG_AM437X_USB2PHY2_HOST
+#endif
+
+/* USB GADGET */
+#if !defined(CONFIG_SPL_BUILD) || \
+ (defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_USBETH_SUPPORT))
+#define CONFIG_USB_DWC3_PHY_OMAP
+#define CONFIG_USB_DWC3_OMAP
+#define CONFIG_USB_DWC3
+#define CONFIG_USB_DWC3_GADGET
+
+#define CONFIG_USB_GADGET
+#define CONFIG_USB_GADGET_DOWNLOAD
+#define CONFIG_USB_GADGET_VBUS_DRAW 2
+#define CONFIG_G_DNL_MANUFACTURER "Texas Instruments"
+#define CONFIG_G_DNL_VENDOR_NUM 0x0403
+#define CONFIG_G_DNL_PRODUCT_NUM 0xBD00
+#define CONFIG_USB_GADGET_DUALSPEED
+#endif
+
+/*
+ * Disable MMC DM for SPL build and can be re-enabled after adding
+ * DM support in SPL
+ */
+#ifdef CONFIG_SPL_BUILD
+#undef CONFIG_DM_MMC
+#endif
+
+#ifndef CONFIG_SPL_BUILD
+/* USB Device Firmware Update support */
+#define CONFIG_USB_FUNCTION_DFU
+#define CONFIG_DFU_RAM
+#define CONFIG_CMD_DFU
+
+#define CONFIG_DFU_MMC
+#define DFU_ALT_INFO_MMC \
+ "dfu_alt_info_mmc=" \
+ "boot part 0 1;" \
+ "rootfs part 0 2;" \
+ "MLO fat 0 1;" \
+ "spl-os-args fat 0 1;" \
+ "spl-os-image fat 0 1;" \
+ "u-boot.img fat 0 1;" \
+ "uEnv.txt fat 0 1\0"
+
+#define DFU_ALT_INFO_EMMC \
+ "dfu_alt_info_emmc=" \
+ "MLO raw 0x100 0x100 mmcpart 0;" \
+ "u-boot.img raw 0x300 0x1000 mmcpart 0\0"
+
+#define CONFIG_DFU_RAM
+#define DFU_ALT_INFO_RAM \
+ "dfu_alt_info_ram=" \
+ "kernel ram 0x80200000 0x4000000;" \
+ "fdt ram 0x80f80000 0x80000;" \
+ "ramdisk ram 0x81000000 0x4000000\0"
+
+#define CONFIG_DFU_SF
+#define DFU_ALT_INFO_QSPI \
+ "dfu_alt_info_qspi=" \
+ "u-boot.bin raw 0x0 0x080000;" \
+ "u-boot.backup raw 0x080000 0x080000;" \
+ "u-boot-spl-os raw 0x100000 0x010000;" \
+ "u-boot-env raw 0x110000 0x010000;" \
+ "u-boot-env.backup raw 0x120000 0x010000;" \
+ "kernel raw 0x130000 0x800000\0"
+
+#define DFUARGS \
+ "dfu_bufsiz=0x10000\0" \
+ DFU_ALT_INFO_MMC \
+ DFU_ALT_INFO_EMMC \
+ DFU_ALT_INFO_RAM \
+ DFU_ALT_INFO_QSPI
+#else
+#define DFUARGS
+#endif
#ifdef CONFIG_QSPI_BOOT
#define CONFIG_SYS_TEXT_BASE 0x30000000
/* SPI */
#undef CONFIG_OMAP3_SPI
#define CONFIG_TI_QSPI
-#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_MACRONIX
#define CONFIG_CMD_SF
#define CONFIG_CMD_SPI
#define CONFIG_TI_SPI_MMAP
-#define CONFIG_SPI_FLASH_BAR
#define CONFIG_QSPI_SEL_GPIO 48
#define CONFIG_SF_DEFAULT_SPEED 48000000
#define CONFIG_DEFAULT_SPI_MODE SPI_MODE_3
+#define CONFIG_QSPI_QUAD_SUPPORT
+#define CONFIG_TI_EDMA3
/* Enhance our eMMC support / experience. */
#define CONFIG_CMD_GPT
#ifndef CONFIG_SPL_BUILD
#define CONFIG_EXTRA_ENV_SETTINGS \
DEFAULT_LINUX_BOOT_ENV \
+ DEFAULT_MMC_TI_ARGS \
"fdtfile=undefined\0" \
"bootpart=0:2\0" \
"bootdir=/boot\0" \
"uuid_disk=${uuid_gpt_disk};" \
"name=rootfs,start=2MiB,size=-,uuid=${uuid_gpt_rootfs}\0" \
"optargs=\0" \
- "mmcdev=0\0" \
- "mmcroot=/dev/mmcblk0p2 rw\0" \
- "mmcrootfstype=ext4 rootwait\0" \
"usbroot=/dev/sda2 rw\0" \
"usbrootfstype=ext4 rootwait\0" \
"usbdev=0\0" \
"ramroot=/dev/ram0 rw\0" \
"ramrootfstype=ext2\0" \
- "mmcargs=setenv bootargs console=${console} " \
- "${optargs} " \
- "root=${mmcroot} " \
- "rootfstype=${mmcrootfstype}\0" \
"usbargs=setenv bootargs console=${console} " \
"${optargs} " \
"root=${usbroot} " \
"if run loadimage; then " \
"run loadfdt; " \
"echo Booting from mmc${mmcdev} ...; " \
- "run mmcargs; " \
+ "run args_mmc; " \
"bootz ${loadaddr} - ${fdtaddr}; " \
"fi;" \
"fi;\0" \
"bootz ${loadaddr} - ${fdtaddr}; " \
"fi;" \
"fi\0" \
+ "fi;" \
+ "usb stop ${usbdev};\0" \
"findfdt="\
"if test $board_name = AM43EPOS; then " \
"setenv fdtfile am43x-epos-evm.dtb; fi; " \
"if test $board_name = AM43_IDK; then " \
"setenv fdtfile am437x-idk-evm.dtb; fi; " \
"if test $fdtfile = undefined; then " \
- "echo WARNING: Could not determine device tree; fi; \0"
+ "echo WARNING: Could not determine device tree; fi; \0" \
+ NANDARGS \
+ NETARGS \
+ DFUARGS \
#define CONFIG_BOOTCOMMAND \
"run findfdt; " \
"run mmcboot;" \
- "run usbboot;"
+ "run usbboot;" \
+ NANDBOOT \
#endif
+#ifndef CONFIG_SPL_BUILD
/* CPSW Ethernet */
-#define CONFIG_CMD_NET
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_PING
#define CONFIG_CMD_MII
-#define CONFIG_DRIVER_TI_CPSW
#define CONFIG_MII
#define CONFIG_BOOTP_DEFAULT
#define CONFIG_BOOTP_DNS
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_NET_RETRY_COUNT 10
-#define CONFIG_NET_MULTI
#define CONFIG_PHY_GIGE
+#endif
+
+#define CONFIG_DRIVER_TI_CPSW
#define CONFIG_PHYLIB
+#define PHY_ANEG_TIMEOUT 8000 /* PHY needs longer aneg time at 1G */
#define CONFIG_SPL_ENV_SUPPORT
#define CONFIG_SPL_NET_VCI_STRING "AM43xx U-Boot SPL"
-#define CONFIG_SPL_ETH_SUPPORT
+#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_ETH_SUPPORT)
+#undef CONFIG_ENV_IS_IN_FAT
+#define CONFIG_ENV_IS_NOWHERE
#define CONFIG_SPL_NET_SUPPORT
+#endif
+
#define CONFIG_SYS_RX_ETH_BUFFER 64
/* NAND support */
"256k(NAND.u-boot-env)," \
"256k(NAND.u-boot-env.backup1)," \
"7m(NAND.kernel)," \
- "-(NAND.rootfs)"
+ "-(NAND.file-system)"
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x00180000
/* NAND: SPL related configs */
#ifdef CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x00300000 /* kernel offset */
#define CONFIG_CMD_SPL_WRITE_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
#endif
-#endif /* !CONFIG_NAND */
+#define NANDARGS \
+ "mtdids=" MTDIDS_DEFAULT "\0" \
+ "mtdparts=" MTDPARTS_DEFAULT "\0" \
+ "nandargs=setenv bootargs console=${console} " \
+ "${optargs} " \
+ "root=${nandroot} " \
+ "rootfstype=${nandrootfstype}\0" \
+ "nandroot=ubi0:rootfs rw ubi.mtd=NAND.file-system,4096\0" \
+ "nandrootfstype=ubifs rootwait=1\0" \
+ "nandboot=echo Booting from nand ...; " \
+ "run nandargs; " \
+ "nand read ${fdtaddr} NAND.u-boot-spl-os; " \
+ "nand read ${loadaddr} NAND.kernel; " \
+ "bootz ${loadaddr} - ${fdtaddr}\0"
+#define NANDBOOT "run nandboot; "
+#else /* !CONFIG_NAND */
+#define NANDARGS
+#define NANDBOOT
+#endif /* CONFIG_NAND */
#endif /* __CONFIG_AM43XX_EVM_H */
projects / people / ms / u-boot.git / blobdiff