mx6sxsabreauto: Remove legacy CONFIG_PCA953X

[people/ms/u-boot.git] / include / configs / bf533-stamp.h

diff --git a/include/configs/bf533-stamp.h b/include/configs/bf533-stamp.h
index 7144c6319fe9909a6b929d22d91b39dfcb30461d..516fe2d021532ba68f6c03447525ba67da1875fc 100644 (file)
--- a/include/configs/bf533-stamp.h
+++ b/include/configs/bf533-stamp.h
@@ -1,5 +1,5 @@
 /*
- * U-boot - Configuration file for BF533 STAMP board
+ * U-Boot - Configuration file for BF533 STAMP board
  */
 
 #ifndef __CONFIG_BF533_STAMP_H__
@@ -7,7 +7,6 @@
 
 #include <asm/config-pre.h>
 
-
 /*
  * Processor Settings
  */
@@ -53,7 +52,6 @@
 #define CONFIG_SYS_MONITOR_LEN (256 * 1024)
 #define CONFIG_SYS_MALLOC_LEN  (384 * 1024)
 
-
 /*
  * Network Settings
  */
@@ -68,9 +66,6 @@
                SSYNC(); \
        } while (0)
 #define CONFIG_HOSTNAME                bf533-stamp
-/* Uncomment next line to use fixed MAC address */
-/* #define CONFIG_ETHADDR      02:80:ad:20:31:b8 */
-
 
 /* I2C */
 #define CONFIG_SYS_I2C
@@ -80,33 +75,8 @@
 /*
  * Software (bit-bang) I2C driver configuration
  */
-#define PF_SCL                 PF3
-#define PF_SDA                 PF2
-#define I2C_INIT               (*pFIO_DIR |=  PF_SCL); asm("ssync;")
-#define I2C_ACTIVE             (*pFIO_DIR |=  PF_SDA); \
-                               *pFIO_INEN &= ~PF_SDA; asm("ssync;")
-#define I2C_TRISTATE           (*pFIO_DIR &= ~PF_SDA); \
-                               *pFIO_INEN |= PF_SDA; asm("ssync;")
-#define I2C_READ               ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); \
-                               asm("ssync;")
-#define I2C_SDA(bit)   if (bit) { \
-                               *pFIO_FLAG_S = PF_SDA; \
-                               asm("ssync;"); \
-                               } \
-                       else    { \
-                               *pFIO_FLAG_C = PF_SDA; \
-                               asm("ssync;"); \
-                               }
-#define I2C_SCL(bit)   if (bit) { \
-                               *pFIO_FLAG_S = PF_SCL; \
-                               asm("ssync;"); \
-                               } \
-                       else    { \
-                               *pFIO_FLAG_C = PF_SCL; \
-                               asm("ssync;"); \
-                               }
-#define I2C_DELAY              udelay(5)       /* 1/4 I2C clock duration */
-
+#define CONFIG_SOFT_I2C_GPIO_SCL       GPIO_PF3
+#define CONFIG_SOFT_I2C_GPIO_SDA       GPIO_PF2
 
 /*
  * Flash Settings
@@ -123,10 +93,10 @@
  */
 #define CONFIG_BFIN_SPI
 #define CONFIG_ENV_SPI_MAX_HZ  30000000
+/*
 #define CONFIG_SF_DEFAULT_SPEED        30000000
-#define CONFIG_SPI_FLASH
 #define CONFIG_SPI_FLASH_ALL
-
+*/
 
 /*
  * Env Storage Settings
@@ -155,13 +125,12 @@
  * it linked after the configuration sector.
  */
 # define LDS_BOARD_TEXT \
-       arch/blackfin/lib/libblackfin.o (.text*); \
-       arch/blackfin/cpu/libblackfin.o (.text*); \
+       arch/blackfin/lib/built-in.o (.text*); \
+       arch/blackfin/cpu/built-in.o (.text*); \
        . = DEFINED(env_offset) ? env_offset : .; \
        common/env_embedded.o (.text*);
 #endif
 
-
 /*
  * I2C Settings
  */
@@ -183,7 +152,6 @@
 /* #define CONFIG_STAMP_CF */
 #if defined(CONFIG_STAMP_CF)
 #define CONFIG_MISC_INIT_R
-#define CONFIG_DOS_PARTITION   1
 #undef  CONFIG_IDE_8xx_DIRECT          /* no pcmcia interface required */
 #undef  CONFIG_IDE_LED                 /* no led for ide supported */
 #undef  CONFIG_IDE_RESET               /* no reset for ide supported */
@@ -204,7 +172,6 @@
 #define CONFIG_EBIU_AMBCTL1_VAL        0x99B3ffc2
 #endif
 
-
 /*
  * Misc Settings
  */
@@ -218,26 +185,8 @@
 /* #define CONFIG_SHOW_BOOT_PROGRESS */
 
 /* define to enable run status via led */
-/* #define CONFIG_STATUS_LED */
-#ifdef CONFIG_STATUS_LED
-#define CONFIG_GPIO_LED
-#define CONFIG_BOARD_SPECIFIC_LED
-/* use LED0 to indicate booting/alive */
-#define STATUS_LED_BOOT 0
-#define STATUS_LED_BIT GPIO_PF2
-#define STATUS_LED_STATE STATUS_LED_ON
-#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 4)
-/* use LED1 to indicate crash */
-#define STATUS_LED_CRASH 1
-#define STATUS_LED_BIT1 GPIO_PF3
-#define STATUS_LED_STATE1 STATUS_LED_ON
-#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
-/* #define STATUS_LED_BIT2 GPIO_PF4 */
-#endif
 
 /* define to enable splash screen support */
-/* #define CONFIG_VIDEO */
-
 
 /*
  * Pull in common ADI header for remaining command/environment setup